belt NISSAN 350Z 2007 Z33 Exterior And Interior Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 50, PDF Size: 2.09 MB
Page 1 of 50
EI-1
EXTERIOR & INTERIOR
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION EI
A
B
EI
Revision: 2006 November2007 350Z
EXTERIOR & INTERIOR
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Precautions for Procedures without Cowl Top Cover ..... 3
Precautions for Work ................................................ 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
CLIP AND FASTENER ..............................................11
Clip and Fastener .................................................... 11
FRONT BUMPER ..................................................... 14
Removal and Installation ........................................ 14
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Removal and Installation of Bumper Side Reflector
(Left Side) ............................................................... 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Removal and Installation of Bumper Side Reflector
(Right Side) ............................................................ 15REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Removal and Installation of Bumper Molding (Upper
side, Lower) ............................................................ 16
REMOVAL ........................................................... 16
INSTALLATION ................................................... 16
REAR BUMPER ........................................................ 17
Removal and Installation ........................................ 17
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
REMOVAL AND INSTALLATION OF BUMPER
SIDE BRACKETS AND FILLET MOLDING ......... 19
COWL TOP ............................................................... 20
Removal and Installation ........................................ 20
REMOVAL ........................................................... 20
INSTALLATION ................................................... 20
FENDER PROTECTOR ............................................ 21
Removal and Installation ........................................ 21
REMOVAL ........................................................... 21
INSTALLATION ................................................... 21
DOOR OUTSIDE MOLDING ..................................... 22
Removal and Installation ........................................ 22
REMOVAL ........................................................... 22
INSTALLATION ................................................... 22
SIDE SILL FINISHER ................................................ 23
Removal and Installation ........................................ 23
REMOVAL ........................................................... 23
INSTALLATION ................................................... 23
FRONT DEFLECTOR ......................................... 24
FLOOR FAIRING ................................................. 24
FLOOR SIDE FAIRING ....................................... 24
REAR DEFLECTOR ............................................ 24
REAR DIFFUSER ............................................... 25
WINDSHIELD MOLDING .......................................... 26
Removal and Installation ........................................ 26
REMOVAL ........................................................... 26
INSTALLATION ................................................... 26
REAR WINDOW MOLDING ...................................... 28
Removal and Installation ........................................ 28
REMOVAL OF BACK DOOR WINDOW MOLD-
Page 3 of 50
PRECAUTIONS
EI-3
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 November2007 350Z
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS00086
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery ServiceNIS001H4
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions for Procedures without Cowl Top CoverNIS001H5
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precautions for WorkNIS00088
After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check
their operation.
Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
Page 35 of 50
BODY SIDE TRIM
EI-35
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: 2006 November2007 350Z
BODY SIDE TRIMPFP:76913
Removal and Installation (for Coupe Models)NIS0008R
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
REAR SIDE FINISHER
Removal
1. Remove kicking plate inner.
2. Remove body side welt.
3. Remove rear side finisher.
Installation
Install in the reverse order of removal.
REAR PILLAR FINISHER
Removal
1. Remove back door weatherstrip. Refer to BL-103, "Removal and Installation of Back Door Weatherstrip" .
2. Remove luggage finisher lower center. Refer to EI-39, "
Removal and Installation (for Coupe Models)" .
3. Disconnect harness connector at luggage room lamp.
4. Remove luggage side finisher upper. Refer to EI-39, "
Removal and Installation (for Coupe Models)" .
5. Remove seat belt shoulder anchor. Refer to SB-4, "
Removal and Installation of Seat Belt (Coupe)" .
6. Remove kicking plate inner.
7. Remove body side welt.
8. Remove rear side finisher.
9. Remove rear pillar finisher.
1. Rear pillar finisher 2. Rear side finisher 3. Body side welt
4. Front pillar garnish 5. Kicking plate outer 6. Kicking plate inner
PIIA2143E
Page 42 of 50
EI-42
LUGGAGE FLOOR TRIM
Revision: 2006 November2007 350Z
5. Remove rear floor box lid and luggage floor finisher mask from luggage floor finisher lower.
6. Remove rear floor box mat and tray.
7. Remove screws, and remove rear floor box striker.
8. Loosen mounting screws and remove rear floor box.
Installation
Install in the reverse order of removal.
LUGGAGE FLOOR FINISHER UPPER
Removal
1. Remove kicking plate inner and partially remove rear of body side welt (RH/LH). Refer to EI-37, "Removal
and Installation (for Roadster Models)" .
2. Remove rear side finisher. Refer to EI-37, "
Removal and Installation (for Roadster Models)" .
3. Remove luggage floor finisher lower.
4. Remove rear parcel box (RH/LH).
5. Remove luggage floor finisher upper.
Installation
Install in the reverse order of removal.
BACK PANEL FINISHER
Removal
1. Remove kicking plate inner and partially remove rear of body side welt (RH/LH). Refer to EI-37, "Removal
and Installation (for Roadster Models)" .
2. Remove rear side finisher. Refer to EI-37, "
Removal and Installation (for Roadster Models)" .
3. Remove cover and shoulder anchor bolt of seat belt (RH/LH). Refer to SB-6, "
Removal and Installation of
Seat Belt (Roadster)" .
4. Remove front guard frame protector (RH/LH).
5. Loosen mounting bolts and remove storage lid deflector.
6. Loosen screws and remove rear guard frame protector (RH/LH).
7. Remove clips, remove back panel finisher assembly.
Installation
Install in the reverse order of removal.
CAUTION:
To install, check if all clips are matched over holes panel on vehicle, then push on.
Page 44 of 50
EI-44
HEADLINING
Revision: 2006 November2007 350Z
HEADLININGPFP:73910
Removal and Installation (for Coupe Models)NIS0008W
REMOVAL
1. Remove back door welt. Refer to EI-47, "BACK DOOR" .
2. Remove luggage floor carpet. Refer to EI-39, "
Removal and Installation (for Coupe Models)" .
3. Remove luggage finisher lower center. Refer to EI-39, "
Removal and Installation (for Coupe Models)" .
4. Disconnect harness connector at luggage room lamp.
5. Remove luggage side finisher upper. Refer to EI-39, "
Removal and Installation (for Coupe Models)" .
6. Remove kicking plate inner. Refer to EI-36, "
KICKING PLATE" .
7. Remove body side welt. Refer to EI-35, "
Removal and Installation (for Coupe Models)" .
8. Remove rear side finisher. Refer to EI-35, "
REAR SIDE FINISHER" .
9. Remove seat belt anchor. Refer to SB-4, "
Removal and Installation of Seat Belt (Coupe)" .
10. Remove rear pillar finisher. Refer to EI-35, "
REAR PILLAR FINISHER" .
11. Remove front pillar garnish. Refer to EI-35, "
Removal and Installation (for Coupe Models)" .
12. Disconnect harness connector at map lamp.
13. Remove sun-visor (RH/LH).
14. Remove sun-visors holder (RH/LH).
NOTE:
Insert flat-bladed screw driver to edge, and turn it 90 degrees
and remove sun-visor holder.
15. Remove dual lock fastener.
16. Remove clips of headlining rear potion.
1. Headlining 2. Dual lock fastener 3. Sun-visor (RH)
4. Sun-visor holder 5. Sun-visor (LH) 6. cap
7. Screw 8. Map lamp assembly
Pawl Metal clip
PIIB7204E
SIIA0224J