display NISSAN 350Z 2007 Z33 Glasses, Windows System And Mirrors Workshop Manual

POWER WINDOW SYSTEM
GW-29
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NIS0004S
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT
DATE MONITOR
ACTIVE TEST
BCM diagnostic test itemCheck item diagnostic
test modeContent
RETAINED PWRWork support Changes setting of each function.
Data monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
Work item Description
RETAINED PWRRap signal’s power supply period can be changed by mode setting. Selects rap signal’s power
supply period between three steps

MODE 1 (45 sec.) / MODE 2 (OFF) / MODE 3 (2 min.).
Monitor item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
DOOR SW–DR Indicates [ON/OFF] condition of driver side door switch.
DOOR SW–AS Indicates [ON/OFF] condition of passenger side door switch.
Test item Description
RETAINED PWRThis test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in “OFF” position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if
“RETAINED PWR” is turned to “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF
position.

GW-68
REAR WINDOW DEFOGGER
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NIS0005N
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
DATA MONITOR
Display Item List
ACTIVE TEST
Display Item List
CONSULT-III Function (IPDM E/R)NIS0005O
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
DATA MONITOR
ACTIVE TEST
84 —A/C control push switch
power supplyInputIgnition switch
(ON or START position)5
87 —Rear window defogger
switch ON signalInput Rear window defogger switch: ON 0
: OFF 5 Te r -
minalWire
ColorItemSignal
input/out-
putConditionVoltag e (V)
(Approx.)
BCM diagnostic test itemCheck item diagnostic
test modeContent
REAR DEFOGGERData monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
Monitor item “Operation” Content
REAR DEF SW “ON/OFF”Displays “Press (ON)/others (OFF)” status determined with the rear window defogger
switch.
IGN ON SW “ON/OFF” Displays “IGN (ON)/OFF” status determined with the ignition switch signal.
Test item Content
REAR DEFOGGER Gives a drive signal to the rear window defogger to activate it.
IPDM E/R diagnostic test
itemCheck item diagnostic
test modeContent
REAR DEFOGGERData monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
Monitored Item Description
RR DEF REQ Indicates [ON/OFF] condition of rear window defogger function by IPDM E/R.
Test Item Description
REAR DEFOGGERThis test is able to check rear window defogger operation. Rear window defogger operates when
“ON” on CONSULT-III screen is touched.