bcm terminal NISSAN 350Z 2007 Z33 Lighting System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 172, PDF Size: 5.8 MB
Page 1 of 172
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT
Revision: 2006 November2007 350Z
LIGHTING SYSTEM
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for Battery Service ................................ 4
General Precautions for Service Operations ............ 4
HEADLAMP (FOR USA) ............................................ 5
Component Parts and Harness Connector Location ..... 5
System Description .................................................. 5
OUTLINE ............................................................... 5
HEADLAMP OPERATION .................................... 6
COMBINATION SWITCH READING FUNCTION ..... 7
EXTERIOR LAMP BATTERY SAVER CONTROL ..... 7
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION ...................................................................... 7
VEHICLE SECURITY SYSTEM ............................ 7
XENON HEADLAMP ............................................. 7
CAN Communication System Description ................ 7
CAN Communication Unit ........................................ 7
Schematic ................................................................ 8
Wiring Diagram — H/LAMP — ................................. 9
Terminals and Reference Values for BCM ............. 13
Terminals and Reference Values for IPDM E/R ..... 15
How to Proceed With Trouble Diagnosis ................ 15
Preliminary Check .................................................. 15
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 15
CONSULT-III Function (BCM) ................................ 17
WORK SUPPORT ............................................... 17
DATA MONITOR ................................................. 17
ACTIVE TEST ..................................................... 18
CONSULT-III Function (IPDM E/R) ........................ 18
DATA MONITOR ................................................. 18
ACTIVE TEST ..................................................... 18
Headlamp Does Not Change To High Beam (Both
Sides) ..................................................................... 19
Headlamp Does Not Change To High Beam (One
Side) ....................................................................... 21
High Beam Indicator Lamp Does Not Illuminate .... 22
Headlamp Low Beam Does Not Illuminate (Both Sides) ..................................................................... 22
Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 24
Headlamps Does Not Turn OFF ............................. 26
General Information for Xenon Headlamp Trouble
Diagnosis ................................................................ 26
Caution: .................................................................. 26
Xenon Headlamp Trouble Diagnosis ...................... 27
Aiming Adjustment .................................................. 27
PREPARATION BEFORE ADJUSTING .............. 27
LOW BEAM AND HIGH BEAM ........................... 28
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 28
Bulb Replacement .................................................. 28
HEADLAMP HIGH/LOW BEAM .......................... 28
PARKING LAMP .................................................. 29
FRONT TURN SIGNAL LAMP ............................ 29
FRONT SIDE MARKER LAMP ........................... 29
Removal and Installation ........................................ 29
REMOVAL ........................................................... 29
INSTALLATION ................................................... 29
Disassembly and Assembly .................................... 30
DISASSEMBLY ................................................... 30
ASSEMBLY ......................................................... 31
Servicing to Replace Headlamps When Damaged ... 31
INSTALLATION OF HEADLAMP BRACKET ....... 31
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 32
Component Parts and Harness Connector Location ... 32
System Description ................................................. 32
OUTLINE ............................................................. 32
HEADLAMP OPERATION ................................... 33
DAYTIME LIGHT OPERATION ........................... 34
OPERATION ........................................................ 35
COMBINATION SWITCH READING FUNCTION ... 35
EXTERIOR LAMP BATTERY SAVER CONTROL ... 35
INTERLOCKED OPERATION WITH REMOTE
KEYLESS ENTRY SYSTEM ............................... 35
INTERLOCKED OPERATION WITH VEHICLE
SECURITY SYSTEM .......................................... 35
Page 2 of 172
LT-2Revision: 2006 November2007 350Z XENON HEADLAMP ........................................... 35
CAN Communication System Description .............. 36
CAN Communication Unit ....................................... 36
Schematic ............................................................... 37
Wiring Diagram — DTRL — ................................... 38
Terminals and Reference Values for BCM .............. 45
Terminals and Reference Values for IPDM E/R ...... 47
How to Proceed With Trouble Diagnosis ................ 47
Preliminary Check .................................................. 47
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 47
CONSULT-III Function (BCM) ................................. 49
WORK SUPPORT ............................................... 49
DATA MONITOR .................................................. 49
ACTIVE TEST ..................................................... 50
CONSULT-III Function (IPDM E/R) ......................... 50
DATA MONITOR .................................................. 50
ACTIVE TEST ..................................................... 50
Daytime Light Control Does Not Operate ............... 51
Headlamp Does Not Change To High Beam (Both
Sides) ..................................................................... 51
Headlamp Does Not Change To High Beam (One
Side) ....................................................................... 54
High Beam Indicator Lamp Does Not Illuminate ..... 55
Headlamp Low Beam Does Not Illuminate (Both
Sides) ..................................................................... 55
Headlamp Low Beam Does Not Illuminate (One
Side) ....................................................................... 57
Headlamps Does Not Turn OFF ............................. 59
General Information for Xenon Headlamp Trouble
Diagnosis ................................................................ 59
Caution: .................................................................. 59
Xenon Headlamp Trouble Diagnosis ...................... 60
Aiming Adjustment .................................................. 60
PREPARATION BEFORE ADJUSTING .............. 60
LOW BEAM AND HIGH BEAM ........................... 61
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 61
Bulb Replacement .................................................. 61
HEADLAMP HIGH/LOW BEAM .......................... 61
PARKING LAMP .................................................. 62
FRONT TURN SIGNAL LAMP ............................ 62
FRONT SIDE MARKER LAMP ............................ 62
Removal and Installation ........................................ 62
REMOVAL ........................................................... 62
INSTALLATION .................................................... 62
Disassembly and Assembly .................................... 63
DISASSEMBLY ................................................... 63
ASSEMBLY ......................................................... 64
Serving to Replace Headlamps When Damaged ... 64
INSTALLATION OF HEADLAMP BRACKET ....... 64
TURN SIGNAL AND HAZARD WARNING LAMPS ... 65
Component Parts and Harness Connector Location ... 65
System Description ................................................. 65
TURN SIGNAL OPERATION ............................... 65
HAZARD WARNING LAMP OPERATION ........... 66
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION .................................................................... 67
COMBINATION SWITCH READING FUNCTION ... 67CAN Communication System Description .............. 67
CAN Communication Unit ....................................... 67
Schematic ............................................................... 68
Wiring Diagram — TURN — ................................... 69
COUPE MODELS ................................................ 69
ROADSTER MODELS ......................................... 73
Terminals and Reference Values for BCM .............. 77
How to Proceed With Trouble Diagnosis ................ 78
Preliminary Check ................................................... 79
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................... 79
CONSULT-III Function (BCM) ................................. 80
DATA MONITOR .................................................. 80
ACTIVE TEST ...................................................... 80
Turn Signal Lamp Does Not Operate ...................... 81
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operate .............................................. 82
Turn Signal Indicator Lamp Does Not Operate ....... 83
Bulb Replacement (Front Turn Signal Lamp) .......... 83
Bulb Replacement (Rear Turn Signal Lamp) .......... 83
Removal and Installation of Front Turn Signal Lamp ... 83
Removal and Installation of Rear Turn Signal Lamp ... 83
LIGHTING AND TURN SIGNAL SWITCH ................ 84
Removal and Installation ......................................... 84
REMOVAL ............................................................ 84
INSTALLATION .................................................... 84
HAZARD SWITCH ..................................................... 85
Removal and Installation ......................................... 85
HAZARD SWITCH (A/T MODELS) ...................... 85
HAZARD SWITCH (M/T MODELS) ..................... 85
COMBINATION SWITCH .......................................... 86
Wiring Diagram —COMBSW— .............................. 86
Combination Switch Reading Function ................... 87
Terminals and Reference Values for BCM .............. 87
CONSULT-III Function (BCM) ................................. 91
DATA MONITOR .................................................. 91
Combination Switch Inspection ............................... 92
Removal and Installation ......................................... 94
STOP LAMP .............................................................. 95
Wiring Diagram — STOP/L — ................................ 95
High-Mounted Stop Lamp (Coupe Models) ............. 97
BULB REPLACEMENT, REMOVAL AND
INSTALLATION .................................................... 97
High-Mounted Stop Lamp (Roadster Models) ......... 97
BULB REPLACEMENT, REMOVAL AND
INSTALLATION .................................................... 97
Stop Lamp ............................................................... 97
BULB REPLACEMENT ........................................ 97
REMOVAL AND INSTALLATION ......................... 97
BACK-UP LAMP ....................................................... 98
Wiring Diagram — BACK/L — ................................ 98
COUPE MODELS (A/T) ....................................... 98
COUPE MODELS (M/T) ...................................... 99
ROADSTER MODELS (A/T) ..............................100
ROADSTER MODELS (M/T) .............................101
Bulb Replacement .................................................102
Removal and Installation .......................................102
PARKING, LICENSE PLATE AND TAIL LAMPS ....103
Component Parts and Harness Connector Location .103
Page 3 of 172
LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z System Description .............................................. 103
OUTLINE ........................................................... 103
OPERATION BY LIGHTING SWITCH .............. 104
COMBINATION SWITCH READING FUNCTION . 104
EXTERIOR LAMP BATTERY SAVER CONTROL . 104
CAN Communication System Description ............ 105
CAN Communication Unit .................................... 105
Schematic ............................................................ 106
Wiring Diagram — TAIL/L — ................................ 107
Terminals and Reference Values for BCM ............ 112
Terminals and Reference Values for IPDM E/R .... 114
How to Proceed With Trouble Diagnosis ............... 114
Preliminary Check ................................................. 114
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................... 114
CONSULT-III Function (BCM) ............................... 115
CONSULT-III Function (IPDM E/R) ....................... 115
Parking, License Plate, Side Marker and Tail Lamps
Do Not Illuminate (for USA) ................................... 116
Parking, License Plate, Side Marker, and Tail Lamps
Do Not Illuminate (for Canada) ............................. 119
Parking, Side Marker, License Plate and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ....... 124
License Plate Lamp .............................................. 125
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................. 125
Front Parking Lamp .............................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
Tail Lamp .............................................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
REAR COMBINATION LAMP ................................ 126
Bulb Replacement ................................................ 126
REAR FENDER SIDE (STOP & TAIL LAMP,
REAR SIDE MARKER LAMP) .......................... 126
REAR BUMPER SIDE (BACK-UP LAMP BULB,
REAR TURN SIGNAL LAMP BULB) ................. 126
Removal and Installation ...................................... 127
REMOVAL ......................................................... 127
INSTALLATION ................................................. 127
INTERIOR ROOM LAMP ........................................ 128
Component Parts and Harness Connector Location . 128
System Description .............................................. 128
POWER SUPPLY AND GROUND .................... 129
SWITCH OPERATION ...................................... 130
MAP LAMP TIMER OPERATION ..................... 130
INTERIOR LAMP BATTERY SAVER CONTROL . 131
Schematic ............................................................ 132Wiring Diagram — ROOM/L — ............................133
COUPE MODELS .............................................133
ROADSTER MODELS ......................................137
Terminals and Reference Values for BCM ............141
How to Proceed with Trouble Diagnosis ...............141
Preliminary Check ................................................142
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................142
CONSULT-III Function (BCM) ..............................143
WORK SUPPORT .............................................143
DATA MONITOR ...............................................143
ACTIVE TEST ...................................................144
Map Lamp Control Does Not Operate (Coupe mod-
els) ........................................................................144
Map Lamp Control Does Not Operate (Roadster
models) .................................................................146
Ignition Key Hole Illumination Does Not Illuminate .148
Luggage Room Lamp Does Not Illuminate (Coupe
Models) .................................................................149
Trunk Room Lamp Does Not Illuminate (Roadster
Models) .................................................................151
Bulb Replacement ................................................153
MAP LAMP ........................................................153
VANITY MIRROR LAMP ...................................154
LUGGAGE ROOM LAMP & TRUNK ROOM
LAMP .................................................................154
IGNITION KEY HOLE ILLUMINATION ..............154
Removal and Installation ......................................155
MAP LAMP ........................................................155
LUGGAGE ROOM LAMP ..................................155
ILLUMINATION .......................................................156
System Description ...............................................156
OUT LINE ..........................................................156
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................157
EXTERIOR LAMP BATTERY SAVER CONTROL .158
CAN Communication System Description ............158
CAN Communication Unit .....................................158
Schematic .............................................................159
Wiring Diagram — ILL — ......................................161
Bulb Replacement ................................................171
LUGGAGE FLOOR BOX LAMP ........................171
CUP HOLDER ILLUMINATION .........................171
Removal and Installation ......................................171
LUGGAGE FLOOR BOX LAMP ........................171
BULB SPECIFICATIONS ........................................172
Headlamp .............................................................172
Exterior Lamp .......................................................172
Interior Lamp/Illumination .....................................172
Page 5 of 172
HEADLAMP (FOR USA)
LT-5
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
HEADLAMP (FOR USA)PFP:26010
Component Parts and Harness Connector LocationNKS004WM
System DescriptionNKS004WN
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
signal requesting the headlamps (and tail lamps) illuminate. This input signal is communicated to the IPDM E/
R (intelligent power distribution module engine room) through the CAN communication lines. The CPU (central
processing unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. These relays,
when energized, direct power to the respective headlamps, which then illuminate.
OUTLINE
Power is supplied at all times
to headlamp high relay, located in IPDM E/R and
to headlamp low relay, located in IPDM E/R, from battery directly,
through 40A fusible link [letter F, located in fuse, fusible link and relay box]
to BCM terminal 55,
through 10A fuse [No.18, located in fuse block (J/B)]
to BCM terminal 42,
through 15A fuse [No.78 located in IPDM E/R]
to CPU located in IPDM E/R,
through 10A fuse [No.71,located in IPDM E/R]
to CPU located in IPDM E/R,
through 10A fuse [No.19, located in fuse block (J/B)]
SKIB7542E
Page 6 of 172
LT-6
HEADLAMP (FOR USA)
Revision: 2006 November2007 350Z
to combination meter terminal 24.
With ignition switch in ON or START position, power is supplied
to CPU located in IPDM E/R,
through 10A fuse [No. 1, located in fuse block (J/B)]
to BCM terminal 38,
through 10A fuse [No.14, located in fuse block (J/B)]
to combination meter terminal 23.
With ignition switch in ACC or ON position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminal 52
through grounds M30 and M66,
to IPDM E/R terminals 38 and 60
through grounds E17, E43 and B102 (with VDC system, navigation system or telephone)
through grounds E17, E43 and F152 (without VDC system, navigation system and telephone),
to combination meter terminals 10, 11 and 12
through grounds M30 and M66.
HEADLAMP OPERATION
Low Beam Operation
With the lighting switch in 2ND position, the BCM receives input signal from combination switch reading func-
tion (Refer to BCS-3, "
COMBINATION SWITCH READING FUNCTION" ) the headlamp to illuminate. This
input signal is communicated to the IPDM E/R through the CAN communication lines. The CPU located in the
IPDM E/R controls the headlamp low relay coil, which when energized, supplies power,
through 15A fuse [No. 76, located in IPDM E/R]
through IPDM E/R terminal 20
to front combination lamp RH terminal 7,
through 15A fuse [No. 86, located in IPDM E/R]
through IPDM E/R terminal 30
to front combination lamp LH terminal 7.
Ground is supplied
to front combination lamp RH terminal 4, and
to front combination lamp LH terminal 4
through grounds E17, E43 and B102 (with VDC system, navigation system or telephone)
through grounds E17, E43 and F152 (without VDC system, navigation system and telephone).
With power and ground supplied, low beam headlamps illuminate.
High Beam Operation/Flash-to-Pass Operation
With the lighting switch in 2ND position and placed in HIGH or PASS position, the BCM receives input signal
requesting headlamp high beams to illuminate. High beam request signal and low beam request signal is com-
municated to the IPDM E/R through CAN communication. The CPU located in the IPDM E/R controls head-
lamp high relay and headlamp low relay turned ON, which when energized, supplies power,
through 15A fuse [No. 76, located in IPDM E/R]
through IPDM E/R terminal 20
to front combination lamp RH terminal 7,
through 15A fuse [No. 86, located in IPDM E/R]
through IPDM E/R terminal 30
to front combination lamp LH terminal 7,
through 10A fuse [No. 72, located in IPDM E/R]
through IPDM E/R terminal 27
Page 7 of 172
![NISSAN 350Z 2007 Z33 Lighting System Workshop Manual HEADLAMP (FOR USA)
LT-7
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
to front combination lamp RH terminal 3,
through 10A fuse [No. 74, located in IPDM E/R]
through IPDM E/R terminal](/img/5/775/w960_775-6.png "NISSAN 350Z 2007 Z33 Lighting System Workshop Manual HEADLAMP (FOR USA)
LT-7
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
to front combination lamp RH terminal 3,
through 10A fuse [No. 74, located in IPDM E/R]
through IPDM E/R terminal")
HEADLAMP (FOR USA)
LT-7
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
to front combination lamp RH terminal 3,
through 10A fuse [No. 74, located in IPDM E/R]
through IPDM E/R terminal 28
to front combination lamp LH terminal 3.
Ground is supplied
to front combination lamp RH terminals 4, and
to front combination lamp LH terminals 4,
through grounds E17, E43 and B102 (with VDC system, navigation system or telephone)
through grounds E17, E43 and F152 (without VDC system, navigation system and telephone).
With the power and ground supplied, headlamp bulbs illuminate. High beam solenoids move the bulb shades
in the front combination lamps, and the bulb shades change to high beam position.
Unified meter and A/C amp. receives signal from BCM through CAN communication lines, and then combina-
tion meter indicator illuminates high beam.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control function is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, then the headlamps are turned off.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-III.
REMOTE KEYLESS ENTRY SYSTEM OPERATION
Refer to BL-59, "REMOTE KEYLESS ENTRY SYSTEM" .
VEHICLE SECURITY SYSTEM
The vehicle security system will flash the high beams if the system is triggered. Refer to BL-125, "VEHICLE
SECURITY (THEFT WARNING) SYSTEM" .
XENON HEADLAMP
Xenon type lamps are used for headlamps. Xenon bulbs do not use a filament. Instead, they produce light
when a high voltage current is passed between two tungsten electrodes through a mixture of xenon (an inert
gas) and certain other metal halides. In addition to strong lighting power, electronic control of the power supply
gives the headlamps stable quality and tone color.
Followings are some advantages of the xenon type headlamp.
The light produced by the headlamps is white color similar to sunlight that is easy to the eyes.
Light output is nearly double that of halogen headlamps, affording increased area of illumination.
Counter-reflected luminance increases and the contrast enhances on the wet road in the rain. That makes
visibility go up more than the increase of the light volume.
Power consumption is approximately 25 percent less than halogen headlamps, reducing battery load.
CAN Communication System DescriptionNKS004WO
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS004WP
Refer to LAN-48, "CAN System Specification Chart" .
Page 13 of 172
HEADLAMP (FOR USA)
LT-13
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
Terminals and Reference Values for BCMNKS004WS
CAUTION:
Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF not to be fluctuated by overloaded.
Turn wiper dial position to 4 except when checking waveform or voltage of wiper dial position.
Wiper dial position can be confirmed on CONSULT-III. Refer to LT- 9 1 , "
DATA MONITOR" .
Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
2GYCombination
switch input 5ONLighting, turn,
wiper switch
(Wiper inter-
mittent dial
position 4)OFF Approx. 0 V
Any of the conditions below
Lighting switch 1ST
Lighting switch HIGH beam
(Operates only HIGH beam
switch)
Approx. 1.0 V
Lighting switch 2ND
Approx. 2.0 V
3L/WCombination
switch input 4ONLighting, turn,
wiper switch
(Wiper inter-
mittent dial
position 4)OFF Approx. 0 V
Any of the conditions below
Lighting switch 2ND
Lighting switch PASSING
(Operates only PASSING switch)
Approx. 1.0 V
11 L GIgnition switch
(ACC)ACC — Battery voltage
PKIB4959J
PKIB4953J
PKIB4959J
Page 15 of 172
HEADLAMP (FOR USA)
LT-15
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
Terminals and Reference Values for IPDM E/RNKS004WT
How to Proceed With Trouble DiagnosisNKS004WU
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 5 , "
System Description" .
3. Perform the preliminary check. Refer to LT- 1 5 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does headlamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Preliminary CheckNKS004WV
CHECK POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
39 L CAN − H— — —
40 P CAN − L— — —
42 GYBattery power
supplyOFF — Battery voltage
52 B Ground ON — Approx. 0 V
55 RBattery power
supplyOFF — Battery voltage Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
Terminal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
20 R/L Headlamp low (RH) ONLighting switch 2ND
positionOFF Approx. 0 V
ON Battery voltage
27 BR Headlamp high (RH) ONLighting switch HIGH or
PASS positionOFF Approx. 0 V
ON Battery voltage
28 R/Y Headlamp high (LH) ONLighting switch HIGH or
PASS positionOFF Approx. 0 V
ON Battery voltage
30 R/W Headlamp low (LH) ONLighting switch 2ND
positionOFF Approx. 0 V
ON Battery voltage
38 B Ground ON — Approx. 0 V
48 L CAN − H— — —
49 P CAN − L— — —
60 B Ground ON — Approx. 0 V
Unit Power source Fuse and fusible link No.
BCMBatteryF
18
Ignition switch ON or START position 1
Ignition switch ACC or ON position 6
Page 16 of 172
LT-16
HEADLAMP (FOR USA)
Revision: 2006 November2007 350Z
Refer to LT- 9 , "Wiring Diagram — H/LAMP —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
IPDM E/R Battery72
74
76
86 Unit Power source Fuse and fusible link No.
Terminals Ignition switch position
(+)
(-) OFF ACC ON
BCM
connectorTerminal
M9011
GroundApprox. 0 VBattery
voltageBattery
voltage
38 Approx. 0 V Approx. 0 VBattery
voltage
M9142Battery
voltageBattery
voltageBattery
voltage
55Battery
voltageBattery
voltageBattery
voltage
PKIB5197E
BCM connector Terminal
GroundContinuity
M91 52 Yes
PKIB5198E
Page 22 of 172
LT-22
HEADLAMP (FOR USA)
Revision: 2006 November2007 350Z
3. CHECK HEADLAMP GROUND
Check continuity between front combination lamp RH or LH harness
connector and ground.
OK or NG
OK >> Check headlamp harness and connector.
NG >> Repair harness or connector.
High Beam Indicator Lamp Does Not IlluminateNKS004X0
1. CHECK BULB
Check bulb of high beam indicator lamp.
OK or NG
OK >> Replace combination meter. Refer to DI-24, "Removal and Installation for Combination Meter" .
NG >> Replace indicator bulb.
Headlamp Low Beam Does Not Illuminate (Both Sides)NKS004X1
1. CHECK COMBINATION SWITCH INPUT SIGNAL
CONSULT-III DATA MONITOR
1. Select "HEAD LAMP SW1" and "HEAD LAMP SW2" of BCM data monitor item.
2. With operating the lighting switch, check the monitor status.
CHECK THE COMBINATION SWITCH
Refer to LT- 9 2 , "
Combination Switch Inspection" .
OK or NG
OK >> GO TO 2.
NG >> Check combination switch (lighting switch). Refer to LT- 9 2 , "
Combination Switch Inspection" .
2. HEADLAMP ACTIVE TEST
CONSULT-III ACTIVE TEST
1. Select "LAMPS" of IPDM E/R active test item.
2. With operating the test item, check the headlamp low beam operation.
IPDM E/R AUTO ACTIVE TEST
1. Start auto active test. Refer to PG-20, "
Auto Active Test" .
2. Check that the headlamp low beam operation.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
Front combination lamp
connectorTerminal
Ground Continuity
RH E24 4
Ye s
LH E40 4
PKIA4907E
When lighting switch is 2ND
position: HEAD LAMP SW1 ON
: HEAD LAMP SW2 ON
Headlamp low beam should operate.
Headlamp low beam should operate.