door lock NISSAN 350Z 2007 Z33 Lighting System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 172, PDF Size: 5.8 MB
Page 28 of 172
LT-28
HEADLAMP (FOR USA)
Revision: 2006 November2007 350Z
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
1. Turn headlamp low beam ON.
2. Use adjusting screws to perform aiming adjustment.
ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Bulb ReplacementNKS004X8
HEADLAMP HIGH/LOW BEAM
1. Turn lighting switch OFF.
2. Open the driver and front passenger window, and then discon-
nect the battery cable from the negative terminal or remove
power fuse.
CAUTION:
After the battery cables are disconnected, never open/close
the driver and/or front passenger door with the window in
the full up position. The automatic window adjusting func-
tion will not work and the side roof panel may be damaged.
3. Remove headlamp. Refer to LT- 2 9 , "
Removal and Installation" .
4. Turn plastic cap counterclockwise and unlock it.
5. Turn bulb socket counterclockwise and unlock it.
6. Unlock retaining spring and remove bulb from headlamp.
7. Installation is reverse order of removal.
PKIB5186E
PKIC4918E
Page 29 of 172
HEADLAMP (FOR USA)
LT-29
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
NOTE:
After installation, perform aiming adjustment. Refer to LT- 2 7 , "
Aiming Adjustment" .
PARKING LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-21, "
FENDER PROTECTOR" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
5. Installation is reverse order of removal.
FRONT TURN SIGNAL LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-21, "
FENDER PROTECTOR" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
5. Installation is reverse order of removal.
FRONT SIDE MARKER LAMP
1. Remove headlamp. Refer to LT- 2 9 , "Removal and Installation" .
2. Replacement integral with headlamp housing assembly.
3. Installation is reverse order of removal.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertightness.
Removal and InstallationNKS004X9
REMOVAL
1. Open the driver and front passenger window, and then disconnect the battery cable from the negative ter-
minal or remove power fuse.
CAUTION:
After battery cables are disconnected, never open/close the driver and/or front passenger door
with the window in the full up position. The automatic window adjusting function will not work and
the side roof panel may be damaged.
2. Remove front bumper fascia. Refer to EI-14, "
FRONT
BUMPER" .
3. Remove headlamp mounting bolts.
4. Pull head lamp toward vehicle front, disconnect connector, and
remove headlamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to LT- 2 7 , "
Aiming Adjustment" . Headlamp high/low beam (Xenon) : 12V - 35W (D2R)
Parking lamp : 12V - 5W
Front turn signal lamp/— : 12V - 28/8W (amber)
Front side marker lamp : LED
PKIA1865E
Headlamp mounting bolt : 6.1 N·m (0.62 kg-m, 54 in-lb)
Page 61 of 172
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LT-61
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
1. Turn headlamp low beam ON.
2. Use adjusting screws to perform aiming adjustment.
ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Bulb ReplacementNKS004XZ
HEADLAMP HIGH/LOW BEAM
1. Turn lighting switch OFF.
2. Open the driver and front passenger window, and then discon-
nect the battery cable from the negative terminal or remove
power fuse.
CAUTION:
After the battery cables are disconnected, never open/close
the driver and/or front passenger door with the window in
the full up position. The automatic window adjusting func-
tion will not work and the side roof panel may be damaged.
3. Remove headlamp. Refer to LT- 6 2 , "
Removal and Installation" .
4. Turn plastic cap counterclockwise and unlock it.
5. Turn bulb socket counterclockwise and unlock it.
6. Unlock retaining spring and remove bulb from headlamp.
7. Installation is the reverse order of removal.
PKIB5186E
PKIC4918E
Page 62 of 172
LT-62
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
Revision: 2006 November2007 350Z
NOTE:
After installation, perform aiming adjustment. Refer to LT- 6 0 , "
Aiming Adjustment" .
PARKING LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-21, "
FENDER PROTECTOR" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
5. Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-21, "
FENDER PROTECTOR" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
5. Installation is the reverse order of removal.
FRONT SIDE MARKER LAMP
1. Remove headlamp. Refer to LT- 6 2 , "Removal and Installation" .
2. Replacement integral with headlamp housing assembly.
3. Installation is reverse order of removal.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertightness.
Removal and InstallationNKS004Y0
REMOVAL
1. Open the driver and front passenger window, and then disconnect the battery cable from the negative ter-
minal or remove power fuse.
CAUTION:
After the battery cables are disconnected, never open/close the driver and/or front passenger door
with the window in the full up position. The automatic window adjusting function will not work and
the side roof panel may be damaged.
2. Remove front bumper fascia. Refer to EI-14, "
FRONT
BUMPER" .
3. Remove headlamp mounting bolts.
4. Pull head lamp toward vehicle front, disconnect connector, and
remove headlamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to LT- 6 0 , "
Aiming Adjustment" . Headlamp high/low beam (Xenon) : 12V - 35W (D2R)
Parking lamp : 12V - 5W
Front turn signal lamp/— : 12V - 28/8W (amber)
Front side marker lamp : LED
PKIA1865E
Headlamp mounting bolt : 6.1N·m (0.62 kg-m, 54 in lb)
Page 128 of 172
LT-128
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationNKS004ZJ
System DescriptionNKS004ZK
When the map lamp switch is in the DOOR position, map lamp ON/OFF is controlled by timer according to sig-
nals from switches including key switch, door switch driver side and assist side, unlock and lock signal from
key fob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
When the map lamp turns ON, there is a gradual brightening over 1 second. When map lamp turns OFF, there
is a gradual dimming over 1 second.
Map lamp timer is controlled by BCM (body control module).
Map lamp timer control settings can be changed with CONSULT-III.
Ignition key hole illumination turns ON at time when driver door is opened (door switch ON) or removed key
fob from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
PKID0829E
Page 129 of 172
INTERIOR ROOM LAMP
LT-129
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
POWER SUPPLY AND GROUND
Power is supplied at all times
through 10A fuse [No.21, located in fuse block (J/B)]
to key switch terminal 2,
through 10A fuse [No.18, located in fuse block (J/B)]
to BCM terminal 42,
through 40A fusible link (letter F, located in fuse, fusible link and relay box)
to BCM terminal 55.
When key is removed from ignition key cylinder, power is interrupted
through key switch terminal 1
to BCM terminal 37.
With ignition switch in ON or START position, power is supplied
through 10A fuse [No.1, located in fuse block (J/B)]
to BCM terminal 38.
When map lamp and vanity mirror lamp power is supplied at times
through BCM terminal 41
to ignition key hole illumination terminal1
to map lamp terminal 3 (Coupe models)
to map lamp terminal 2 (Roadster models)
to luggage room lamp terminal 1 (Coupe models)
to trunk room lamp terminal 1 (Roadster models) and
to vanity mirror lamp LH and RH terminals 1.
Ground is supplied
to BCM terminal 52
through grounds M30 and M66.
When driver side door is opened, ground is supplied
through case ground of driver side door switch
to BCM terminal 62.
When passenger side door is opened, ground is supplied
through case ground of passenger side door switch
to BCM terminal 12.
When back door is opened, ground is supplied (Coupe models)
through grounds B5, B6, D105 and T14
to back door switch terminal 3
through back door switch terminal 1
to BCM terminal 58.
When trunk lid is opened, ground is supplied (Roadster models)
through grounds B5, B6 and T14
to trunk lid lock assembly (trunk room lamp switch) terminal 1
through trunk lid lock assembly (trunk room lamp switch) terminal 3
to BCM terminal 57.
When the driver side door or passenger side door is unlocked by door lock and unlock switch, The BCM
receives unlock signal with power window serial link
through grounds M30 and M66
to power window main switch (door lock and unlock switch) terminal 15 or power window sub switch (door
lock and unlock switch) terminal 11
through power window main switch (door lock and unlock switch) terminal 12 and power window sub
switch (door lock and unlock switch) terminal 16
to BCM terminal 22.
Page 130 of 172
LT-130
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
When the driver side door is unlocked by door key cylinder switch, The BCM receives information by commu-
nicating with power window main switch
through grounds M30 and M66
to door key cylinder switch terminal 2
through door key cylinder switch terminal 1
to power window main (door lock and unlock switch) switch terminal 7
through power window main switch (door lock and unlock switch) terminal 12
to BCM terminal 22.
When a signal, or combination of signals is received by BCM, ground is supplied
through BCM terminal 48
to map lamp terminal 2 (Coupe models)
to map lamp terminal 3 (Roadster models).
With power and ground are supplied, map lamp illuminates.
SWITCH OPERATION
When map lamp switch is ON, ground is supplied
to map lamp terminal 1 (Coupe models)
to map lamp terminal 1 (Roadster models)
through grounds M30 and M66.
And power is supplied
through BCM terminal 41
to ignition key hole illumination terminal 1
to map lamp terminal 3 (Coupe models)
to map lamp terminal 2 (Roadster models).
When vanity mirror lamp LH and RH is ON, ground is supplied
to vanity mirror lamp LH and RH terminals 2
through grounds M30 and M66.
And power is supplied
through BCM terminal 41
to vanity mirror lamp terminal 1.
MAP LAMP TIMER OPERATION
When the map lamp switch is in the DOOR position, and when all conditions below are met, BCM performs
timer control (maximum 30 seconds) for map lamp ON/OFF.
In addition, when map lamp turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied at all times
to 10A fuse [No. 21 located in fuse block (J/B)]
through key switch terminal 2.
When all doors are closed (all door switches OFF) and key is removed from key cylinder (key switch OFF),
power will not be supplied to BCM terminal 37.
Ground is supplied
through BCM terminal 22
to power window main switch (door lock and unlock switch) terminal 12.
At this time, BCM detects that driver door is unlocked. It determines that map lamp timer operation conditions
are met, and turns map lamp ON for 30 seconds.
When all doors are closed (all door switches OFF) and key is in key cylinder (key switch ON),
Power is supplied
through key switch terminal 1
to BCM terminal 37.
When the key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated.
BCM detects that key has been removed. It determines that map lamp timer conditions are met, and turns
map lamp ON for 30 seconds.
Page 131 of 172
INTERIOR ROOM LAMP
LT-131
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
When driver door opens → closes, and key is not inserted in key switch (key switch OFF), BCM terminal 62
changes between 0V (door open) → 5V (door closed). BCM determines that conditions for spot lamp opera-
tion are met and turns interior lamp ON for 30 seconds.
Timer control is canceled under the following conditions.
Driver door is locked (When locked key fob or power window main switch (door lock and unlock switch,
door key cylinder switch).
Driver door is opened (driver door switch turns ON).
Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL
If the room lamp remains illuminated by door switch open signal, or if room lamp switch is in the ON position
for more than 30 minutes after the ignition switch is turned to the OFF position, BCM will automatically turn off
map lamp, luggage room lamp (Coupe models), trunk room lamp (Roadster models) and vanity mirror lamp.
After lamps turn OFF by battery saver system, the lamps illuminate again when
signal from key fob, door lock and unlock switch, or key cylinder is locked or unlocked,
door is opened or closed,
key is removed from ignition key cylinder or inserted in ignition key cylinder.
Interior lamp battery saver control period can be changed by the function setting of CONSULT-III.
Page 141 of 172
INTERIOR ROOM LAMP
LT-141
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
Terminals and Reference Values for BCMNKS004ZN
*1: Roadster models, *2: Coupe models
How to Proceed with Trouble DiagnosisNKS004ZO
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 1 2 8 , "
System Description" .
3. Perform preliminary check. Refer to LT- 1 4 2 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
1PUIgnition keyhole illumination
signalOFFDoor is locked. (SW OFF) Battery voltage
Door is unlocked. (SW ON) Approx. 0 V
12 P Front door switch AS signal OFF Front door switch ASON (open) Approx. 0 V
OFF (closed) Battery voltage
22 YPower window switch serial
linkON —
37 B/RKey-in detection switch sig-
nalOFFVehicle key is removed. Approx. 0 V
Vehicle key is inserted. Battery voltage
38 W/L Ignition power supply ON — Battery voltage
39 L CAN − H—— —
40 P CAN − L—— —
41 R/B Battery saver output signalOFF30 minutes after ignition switch is turned
to OFF.Approx. 0 V
ON — Battery voltage
42 GY Battery power supply OFF — Battery voltage
48 P Map lamp output signal OFFMap lamp door
switch: DOOR posi-
tionAny
door
switchON
(open)Approx. 0 V
OFF
(closed)Battery voltage
52 B Ground ON — Approx. 0 V
55 R Battery power supply OFF — Battery voltage
57*
1R/WTrunk room lamp switch sig-
nalOFFTrunk room lamp
switchON (open) Approx. 0 V
OFF (closed) Battery voltage
58*
2R/W Back door switch signal OFFLuggage room lamp
switch ON (open) Approx. 0 V
OFF (closed) Battery voltage
62 L Front door switch DR signal OFF Front door switch DRON (open) Approx. 0 V
OFF (closed) Battery voltage
64GY/R
*1
BR*2Trunk room lamp*1 or lug-
gage lamp*2 switch signalOFFTrunk room lamp*
1
or back door*2
switchON (open) Approx. 0 V
OFF (closed) Battery voltage
PKIA7023E
Page 143 of 172
INTERIOR ROOM LAMP
LT-143
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NKS004ZQ
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
WORK SUPPORT
Display Item List
Reference between “MODE” and “TIME” for “TURN ON/OFF”
DATA MONITOR
Display Item List
NOTE:
This item is displayed, but cannot be monitored.BCM diagnosis part Diagnosis mode Description
INT LAMPWORK SUPPORT Changes the setting for each function.
DATA MONITOR Displays BCM input data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending driving signal to them.
Item Description CONSULT-III
SET I/L D−UNLCK INTCONThe 30 seconds glowing function interior room lamps and ignition keyhole illumi-
nation can be selected when driver door is released (unlocked). ON/OFF
ROOM LAMP ON TIME SETThe time in order to escalate illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned on.MODE 1 – 7
ROOM LAMP OFF TIME SETThe time in order to diminish illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned off.MODE 1 – 7
MODE 1 2 3 4 5 6 7
Time (sec.) 0.5 1 2 3 4 5 0
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from ignition switch signal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from key switch signal.
DOOR SW - DR “ON/OFF”Displays status of driver door as judged from driver door switch signal. (Door is open: ON/Door
is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door switch
signal.
DOOR SW - RR
NOTE“OFF” —
DOOR SW - RL
NOTE“OFF” —
BACK DOOR SW “ON/OFF”
Displays status of back door as judged from back door switch signal. (Coupe models)
Displays status of rear trunk hood as judged from trunk lamp switch signal. (Roadster mod-
els)
KEY CYL LK - SW “ON/OFF” Displays “Door locked (ON) status, determined from key cylinder lock switch in driver door.
KEY CYL UN - SW “ON/OFF” Displays “Door unlocked (OFF) status, determined from key cylinder lock switch in driver door.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from locking detection
switch in driver door.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from locking detection switch in passenger
door.
KEYLESS LOCK “ON/OFF” Displays “Locked (ON)/Other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK “ON/OFF” Displays “Unlocked (ON)/Other (OFF)” status, determined from unlock signal.