trunk NISSAN 350Z 2007 Z33 Lighting System Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: 350Z, Model: NISSAN 350Z 2007 Z33Pages: 172, PDF Size: 5.8 MB
Page 3 of 172
LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z System Description .............................................. 103
OUTLINE ........................................................... 103
OPERATION BY LIGHTING SWITCH .............. 104
COMBINATION SWITCH READING FUNCTION . 104
EXTERIOR LAMP BATTERY SAVER CONTROL . 104
CAN Communication System Description ............ 105
CAN Communication Unit .................................... 105
Schematic ............................................................ 106
Wiring Diagram — TAIL/L — ................................ 107
Terminals and Reference Values for BCM ............ 112
Terminals and Reference Values for IPDM E/R .... 114
How to Proceed With Trouble Diagnosis ............... 114
Preliminary Check ................................................. 114
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................... 114
CONSULT-III Function (BCM) ............................... 115
CONSULT-III Function (IPDM E/R) ....................... 115
Parking, License Plate, Side Marker and Tail Lamps
Do Not Illuminate (for USA) ................................... 116
Parking, License Plate, Side Marker, and Tail Lamps
Do Not Illuminate (for Canada) ............................. 119
Parking, Side Marker, License Plate and Tail Lamps
Do Not Turn OFF (After Approx. 10 Minutes) ....... 124
License Plate Lamp .............................................. 125
BULB REPLACEMENT, REMOVAL AND
INSTALLATION ................................................. 125
Front Parking Lamp .............................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
Tail Lamp .............................................................. 125
BULB REPLACEMENT ..................................... 125
REMOVAL AND INSTALLATION ...................... 125
REAR COMBINATION LAMP ................................ 126
Bulb Replacement ................................................ 126
REAR FENDER SIDE (STOP & TAIL LAMP,
REAR SIDE MARKER LAMP) .......................... 126
REAR BUMPER SIDE (BACK-UP LAMP BULB,
REAR TURN SIGNAL LAMP BULB) ................. 126
Removal and Installation ...................................... 127
REMOVAL ......................................................... 127
INSTALLATION ................................................. 127
INTERIOR ROOM LAMP ........................................ 128
Component Parts and Harness Connector Location . 128
System Description .............................................. 128
POWER SUPPLY AND GROUND .................... 129
SWITCH OPERATION ...................................... 130
MAP LAMP TIMER OPERATION ..................... 130
INTERIOR LAMP BATTERY SAVER CONTROL . 131
Schematic ............................................................ 132Wiring Diagram — ROOM/L — ............................133
COUPE MODELS .............................................133
ROADSTER MODELS ......................................137
Terminals and Reference Values for BCM ............141
How to Proceed with Trouble Diagnosis ...............141
Preliminary Check ................................................142
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ..................................................................142
CONSULT-III Function (BCM) ..............................143
WORK SUPPORT .............................................143
DATA MONITOR ...............................................143
ACTIVE TEST ...................................................144
Map Lamp Control Does Not Operate (Coupe mod-
els) ........................................................................144
Map Lamp Control Does Not Operate (Roadster
models) .................................................................146
Ignition Key Hole Illumination Does Not Illuminate .148
Luggage Room Lamp Does Not Illuminate (Coupe
Models) .................................................................149
Trunk Room Lamp Does Not Illuminate (Roadster
Models) .................................................................151
Bulb Replacement ................................................153
MAP LAMP ........................................................153
VANITY MIRROR LAMP ...................................154
LUGGAGE ROOM LAMP & TRUNK ROOM
LAMP .................................................................154
IGNITION KEY HOLE ILLUMINATION ..............154
Removal and Installation ......................................155
MAP LAMP ........................................................155
LUGGAGE ROOM LAMP ..................................155
ILLUMINATION .......................................................156
System Description ...............................................156
OUT LINE ..........................................................156
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................157
EXTERIOR LAMP BATTERY SAVER CONTROL .158
CAN Communication System Description ............158
CAN Communication Unit .....................................158
Schematic .............................................................159
Wiring Diagram — ILL — ......................................161
Bulb Replacement ................................................171
LUGGAGE FLOOR BOX LAMP ........................171
CUP HOLDER ILLUMINATION .........................171
Removal and Installation ......................................171
LUGGAGE FLOOR BOX LAMP ........................171
BULB SPECIFICATIONS ........................................172
Headlamp .............................................................172
Exterior Lamp .......................................................172
Interior Lamp/Illumination .....................................172
Page 17 of 172
HEADLAMP (FOR USA)
LT-17
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NKS004WW
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
WORK SUPPORT
Display Item List
DATA MONITOR
Display Item List
NOTE:
This item is displayed, but cannot be monitored.BCM diagnosis part Diagnosis mode Description
HEADLAMPWORK SUPPORT Changes the setting for each function.
DATA MONITOR Displays BCM input data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
BCMSELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
Item Description CONSULT-III Factory setting
BATTERY SAVER SETExterior lamp battery saver control mode can be changed in this mode.
Selects exterior lamp battery saver control mode between two ON/OFF.ON×
OFF —
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
ACC ON SW “ON/OFF” Displays “ACC (ON)/OFF, Ignition OFF (OFF)” status judged from ignition switch signal.
HI BEAM SW “ON/OFF”Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting
switch signal.
HEAD LAMP SW 1 “ON/OFF”Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 1 judged from light-
ing switch signal.
HEAD LAMP SW 2 “ON/OFF”Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from light-
ing switch signal.
LIGHT SW 1 ST “ON/OFF”Displays status (lighting switch 1ST or 2ND position: ON/Others: OFF) of lighting switch
judged from lighting switch signal.
PASSING SW “ON/OFF”Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from
lighting switch signal.
FR FOG SW
NOTE“ON/OFF” —
DOOR SW - DR “ON/OFF”Displays status of driver door as judged from driver door switch signal. (Door is open: ON/
Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays status of passenger door as judged from passenger door switch signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW - RR
NOTE“OFF” —
DOOR SW - RL
NOTE“OFF” —
BACK DOOR SW “ON/OFF”
Displays status of back door as judged from back door switch signal. (Coupe models)
Displays status of rear trunk hood as judged from trunk lamp switch signal. (Roadster mod-
els)
TURN SIGNAL R “ON/OFF” Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L “ON/OFF” Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
CARGO LAMP SW
NOTE“OFF” —
Page 49 of 172
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LT-49
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NKS004XM
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
WORK SUPPORT
Display Item List
DATA MONITOR
Display Item List
NOTE:
This item is displayed, but cannot be monitored.BCM diagnosis part Diagnosis mode Description
HEADLAMPWORK SUPPORT Changes the setting for each function.
DATA MONITOR Displays BCM input data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
BCMSELF-DIAG RESULTS BCM performs self-diagnosis of CAN communication.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
Item Description CONSULT-III Factory setting
BATTERY SAVER SETExterior lamp battery saver control mode can be changed in this mode.
Select exterior lamp battery saver control mode between two ON/OFF.ON×
OFF —
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch signal.
ACC ON SW “ON/OFF” Displays “ACC (ON)/OFF, Ignition OFF (OFF)” status judged from ignition switch signal.
HI BEAM SW “ON/OFF”Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from light-
ing switch signal.
HEAD LAMP SW 1 “ON/OFF”Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 1 judged from
lighting switch signal.
HEAD LAMP SW 2 “ON/OFF”Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
LIGHT SW 1 ST “ON/OFF”Displays status (lighting switch 1ST or 2ND position: ON/Others: OFF) of lighting switch
judged from lighting switch signal.
PASSING SW “ON/OFF”Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from
lighting switch signal.
FR FOG SW
NOTE“ON/OFF” —
DOOR SW - DR “ON/OFF”Displays status of driver door as judged from driver door switch signal. (Door is open: ON/
Door is closed: OFF)
DOOR SW - AS “ON/OFF”Displays status of passenger door as judged from passenger door switch signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW - RR
NOTE“OFF” —
DOOR SW - RL
NOTE“OFF” —
BACK DOOR SW “ON/OFF”
Displays status of back door as judged from back door switch signal. (Coupe models)
Displays status of rear trunk hood as judged from trunk lamp switch signal. (Roadster mod-
els)
TURN SIGNAL R “ON/OFF” Displays status (Turn right: ON/Others: OFF) as judged from lighting switch signal.
TURN SIGNAL L “ON/OFF” Displays status (Turn left: ON/Others: OFF) as judged from lighting switch signal.
ENGINE RUN “ON/OFF”Displays status (engine running: ON/ engine stopped: OFF) of engine judged from engine run
signal.
PKB SW “ON/OFF”Displays status (parking brake released: ON/ parking brake applied: OFF) of parking brake
switch judged from parking brake switch signal.
CARGO LAMP SW
NOTE“OFF” —
Page 129 of 172
INTERIOR ROOM LAMP
LT-129
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
POWER SUPPLY AND GROUND
Power is supplied at all times
through 10A fuse [No.21, located in fuse block (J/B)]
to key switch terminal 2,
through 10A fuse [No.18, located in fuse block (J/B)]
to BCM terminal 42,
through 40A fusible link (letter F, located in fuse, fusible link and relay box)
to BCM terminal 55.
When key is removed from ignition key cylinder, power is interrupted
through key switch terminal 1
to BCM terminal 37.
With ignition switch in ON or START position, power is supplied
through 10A fuse [No.1, located in fuse block (J/B)]
to BCM terminal 38.
When map lamp and vanity mirror lamp power is supplied at times
through BCM terminal 41
to ignition key hole illumination terminal1
to map lamp terminal 3 (Coupe models)
to map lamp terminal 2 (Roadster models)
to luggage room lamp terminal 1 (Coupe models)
to trunk room lamp terminal 1 (Roadster models) and
to vanity mirror lamp LH and RH terminals 1.
Ground is supplied
to BCM terminal 52
through grounds M30 and M66.
When driver side door is opened, ground is supplied
through case ground of driver side door switch
to BCM terminal 62.
When passenger side door is opened, ground is supplied
through case ground of passenger side door switch
to BCM terminal 12.
When back door is opened, ground is supplied (Coupe models)
through grounds B5, B6, D105 and T14
to back door switch terminal 3
through back door switch terminal 1
to BCM terminal 58.
When trunk lid is opened, ground is supplied (Roadster models)
through grounds B5, B6 and T14
to trunk lid lock assembly (trunk room lamp switch) terminal 1
through trunk lid lock assembly (trunk room lamp switch) terminal 3
to BCM terminal 57.
When the driver side door or passenger side door is unlocked by door lock and unlock switch, The BCM
receives unlock signal with power window serial link
through grounds M30 and M66
to power window main switch (door lock and unlock switch) terminal 15 or power window sub switch (door
lock and unlock switch) terminal 11
through power window main switch (door lock and unlock switch) terminal 12 and power window sub
switch (door lock and unlock switch) terminal 16
to BCM terminal 22.
Page 131 of 172
INTERIOR ROOM LAMP
LT-131
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
When driver door opens → closes, and key is not inserted in key switch (key switch OFF), BCM terminal 62
changes between 0V (door open) → 5V (door closed). BCM determines that conditions for spot lamp opera-
tion are met and turns interior lamp ON for 30 seconds.
Timer control is canceled under the following conditions.
Driver door is locked (When locked key fob or power window main switch (door lock and unlock switch,
door key cylinder switch).
Driver door is opened (driver door switch turns ON).
Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL
If the room lamp remains illuminated by door switch open signal, or if room lamp switch is in the ON position
for more than 30 minutes after the ignition switch is turned to the OFF position, BCM will automatically turn off
map lamp, luggage room lamp (Coupe models), trunk room lamp (Roadster models) and vanity mirror lamp.
After lamps turn OFF by battery saver system, the lamps illuminate again when
signal from key fob, door lock and unlock switch, or key cylinder is locked or unlocked,
door is opened or closed,
key is removed from ignition key cylinder or inserted in ignition key cylinder.
Interior lamp battery saver control period can be changed by the function setting of CONSULT-III.
Page 141 of 172
INTERIOR ROOM LAMP
LT-141
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
Terminals and Reference Values for BCMNKS004ZN
*1: Roadster models, *2: Coupe models
How to Proceed with Trouble DiagnosisNKS004ZO
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 1 2 8 , "
System Description" .
3. Perform preliminary check. Refer to LT- 1 4 2 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Does interior room lamp operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
1PUIgnition keyhole illumination
signalOFFDoor is locked. (SW OFF) Battery voltage
Door is unlocked. (SW ON) Approx. 0 V
12 P Front door switch AS signal OFF Front door switch ASON (open) Approx. 0 V
OFF (closed) Battery voltage
22 YPower window switch serial
linkON —
37 B/RKey-in detection switch sig-
nalOFFVehicle key is removed. Approx. 0 V
Vehicle key is inserted. Battery voltage
38 W/L Ignition power supply ON — Battery voltage
39 L CAN − H—— —
40 P CAN − L—— —
41 R/B Battery saver output signalOFF30 minutes after ignition switch is turned
to OFF.Approx. 0 V
ON — Battery voltage
42 GY Battery power supply OFF — Battery voltage
48 P Map lamp output signal OFFMap lamp door
switch: DOOR posi-
tionAny
door
switchON
(open)Approx. 0 V
OFF
(closed)Battery voltage
52 B Ground ON — Approx. 0 V
55 R Battery power supply OFF — Battery voltage
57*
1R/WTrunk room lamp switch sig-
nalOFFTrunk room lamp
switchON (open) Approx. 0 V
OFF (closed) Battery voltage
58*
2R/W Back door switch signal OFFLuggage room lamp
switch ON (open) Approx. 0 V
OFF (closed) Battery voltage
62 L Front door switch DR signal OFF Front door switch DRON (open) Approx. 0 V
OFF (closed) Battery voltage
64GY/R
*1
BR*2Trunk room lamp*1 or lug-
gage lamp*2 switch signalOFFTrunk room lamp*
1
or back door*2
switchON (open) Approx. 0 V
OFF (closed) Battery voltage
PKIA7023E
Page 143 of 172
INTERIOR ROOM LAMP
LT-143
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NKS004ZQ
CONSULT-III can display each diagnostic item using the diagnostic test mode shown following.
WORK SUPPORT
Display Item List
Reference between “MODE” and “TIME” for “TURN ON/OFF”
DATA MONITOR
Display Item List
NOTE:
This item is displayed, but cannot be monitored.BCM diagnosis part Diagnosis mode Description
INT LAMPWORK SUPPORT Changes the setting for each function.
DATA MONITOR Displays BCM input data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending driving signal to them.
Item Description CONSULT-III
SET I/L D−UNLCK INTCONThe 30 seconds glowing function interior room lamps and ignition keyhole illumi-
nation can be selected when driver door is released (unlocked). ON/OFF
ROOM LAMP ON TIME SETThe time in order to escalate illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned on.MODE 1 – 7
ROOM LAMP OFF TIME SETThe time in order to diminish illumination can be adjusted when interior room
lamps and ignition keyhole illumination is turned off.MODE 1 – 7
MODE 1 2 3 4 5 6 7
Time (sec.) 0.5 1 2 3 4 5 0
Monitor item Contents
IGN ON SW “ON/OFF” Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from ignition switch signal.
KEY ON SW “ON/OFF” Displays “Key inserted (ON)/key removed (OFF)” status judged from key switch signal.
DOOR SW - DR “ON/OFF”Displays status of driver door as judged from driver door switch signal. (Door is open: ON/Door
is closed: OFF)
DOOR SW - AS “ON/OFF”Displays “Door open (ON)/Door closed (OFF)” status, determined from passenger door switch
signal.
DOOR SW - RR
NOTE“OFF” —
DOOR SW - RL
NOTE“OFF” —
BACK DOOR SW “ON/OFF”
Displays status of back door as judged from back door switch signal. (Coupe models)
Displays status of rear trunk hood as judged from trunk lamp switch signal. (Roadster mod-
els)
KEY CYL LK - SW “ON/OFF” Displays “Door locked (ON) status, determined from key cylinder lock switch in driver door.
KEY CYL UN - SW “ON/OFF” Displays “Door unlocked (OFF) status, determined from key cylinder lock switch in driver door.
CDL LOCK SW “ON/OFF”Displays “Door locked (ON)/Door unlocked (OFF) status, determined from locking detection
switch in driver door.
CDL UNLOCK SW “ON/OFF”Displays “Door unlocked (OFF)” status, determined from locking detection switch in passenger
door.
KEYLESS LOCK “ON/OFF” Displays “Locked (ON)/Other (OFF)” status, determined from lock signal.
KEYLESS UNLOCK “ON/OFF” Displays “Unlocked (ON)/Other (OFF)” status, determined from unlock signal.
Page 144 of 172
LT-144
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
ACTIVE TEST
Display Item List
NOTE:
This item is displayed, but cannot be tested.
Map Lamp Control Does Not Operate (Coupe models)NKS004ZR
1. CHECK BETWEEN EACH SWITCH AND BCM
1. Select "INT LAMP" of BCM data monitor item.
2. Make sure switches listed in display item list turn ON-OFF linked with switch operation. Refer to LT- 1 4 3 ,
"Display Item List" for switches and their functions.
OK or NG
OK >> GO TO 2.
NG >> Inspect malfunctioning switch system.
2. CHECK BETWEEN BCM AND MAP LAMP
1. Select "INT LAMP" of BCM active test item.
2. With operating the test item, check the map lamp operation (When map lamp switch is in DOOR position).
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> GO TO 3.
3. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between map lamp harness connector and
ground.
OK or NG
OK >> GO TO 6.
NG >> GO TO 4.
Test item Description
INT LAMP Map lamp can be operated by any ON−OFF operations.
IGN ILLUM
NOTE—
STEM LAMP TEST
NOTE—
LUGGAGE LAMP TEST
Luggage room lamp can be operated by any ON−OFF operations. (Coupe models)
Trunk room lamp can be operated by any ON−OFF operations. (Roadster models)
Map lamp should operate.
Te r m i n a l
Voltage
(Approx.) (+)
(-)
Map lamp connector Terminal
R52 3 Ground Battery voltage
SKIB7672E
Page 151 of 172
INTERIOR ROOM LAMP
LT-151
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
7. CHECK LUGGAGE ROOM LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and luggage
room lamp harness connector.
OK or NO
OK >> Replace BCM if luggage room lamp does not work after setting the connector again. Refer to
BCS-17, "
Removal and Installation of BCM" .
NG >> Repair harness or connector.
Trunk Room Lamp Does Not Illuminate (Roadster Models)NKS004ZV
1. CHECK BULB
Inspect bulb of trunk room lamp.
OK or NG
OK >> GO TO 2.
NG >> Replace map lamp.
2. CHECK BETWEEN EACH SWITCH AND BCM
1. Select "LUGGAGE LAMP TEST" of BCM data monitor item.
2. Make sure switches listed in display item list turn ON-OFF linked with switch operation. Refer to LT- 1 4 3 ,
"Display Item List" for switches and their functions.
OK or NG
OK >> GO TO 3.
NG >> Inspect malfunctioning switch system.
3. CHECK BETWEEN BCM AND TRUNK ROOM LAMP
1. Select “BCM” on CONSULT-III. Select “LUGGAGE LAMP TEST” active test.
2. With operating the test item, check the trunk room lamp operation.
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> GO TO 4.
Terminals
Continuity BCM Luggage room lamp
Connector Terminal Connector Terminal
B83 64 T13 2 Yes
PKIB5168E
Trunk room lamp should operate.
Page 152 of 172
LT-152
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
4. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between trunk room lamp harness connector and
ground.
OK or NG
OK >> GO TO 7.
NG >> GO TO 5.
5. CHECK TRUNK ROOM LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and trunk room lamp connector.
3. Check continuity between BCM harness connector and trunk
room lamp harness connector.
OK or NO
OK >> GO TO 6.
NG >> Repair harness or connector.
6. CHECK SHORT CIRCUIT
Check continuity between trunk room lamp harness connector and
ground.
OK or NG
OK >> Replace BCM if trunk room lamp does not work after
setting the connector again. Refer to BCS-17, "
Removal
and Installation of BCM" .
NG >> Repair harness or connector.
Te r m i n a l
Voltag e
(Approx.) (+)
(-)
Trunk room lamp
connectorTe r m i n a l
T29 1 Ground Battery voltage
SKIB7680E
Te r m i n a l s
Continuity BCM Trunk room lamp
Connector Terminal Connector Terminal
M91 41 T29 1 Yes
PKIB5169E
Trunk room lamp
connectorTe r m i n a l
GroundContinuity
T29 1 No
PKIA7201E