trunk NISSAN 350Z 2007 Z33 Lighting System User Guide

INTERIOR ROOM LAMP
LT-153
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
7. CHECK TRUNK ROOM LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and trunk
room lamp harness connector.
OK or NO
OK >> Replace BCM if trunk room lamp does not work after
setting the connector again. Refer to BCS-17, "
Removal
and Installation of BCM" .
NG >> Repair harness or connector.
Bulb ReplacementNKS004ZW
MAP LAMP
Coupe Models
1. Open driver and passenger window, and then disconnect battery
cable from the negative terminal.
CAUTION:
After battery cables are disconnected, never open/close
driver and/or passenger door with the window in the full up
position. Automatic window adjusting function will not
work and side roof panel may be damaged.
2. Remove lens using clip driver or suitable tool.
3. Remove bulb.
4. Installation is the reverse order of removal.
Roadster Models
1. Open driver and passenger window, and then disconnect battery
cable from the negative terminal.
CAUTION:
After battery cables are disconnected, never open/close
driver and/or passenger door with the window in the full up
position. Automatic window adjusting function will not
work and side roof panel may be damaged.
2. Remove lens using clip driver or suitable tool.
3. Remove bulb.
4. Installation is the reverse order of removal.
Terminals
Continuity BCM Trunk room lamp
Connector Terminal Connector Terminal
B83 64 T29 2 Yes
PKIB5170E
Map lamp : 12V - 8WPKIA1882E
Map lamp : 12V - 8WPKIA3699E

LT-154
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb.
3. Installation is the reverse order of removal.
LUGGAGE ROOM LAMP & TRUNK ROOM LAMP
Luggage Room Lamp (Coupe Models)
1. Remove luggage room lamp. Refer to LT- 1 5 5 , "Removal and Installation" .
2. Remove bulb.
3. Installation is the reverse order of removal.
Trunk Room Lamp (Roadster Models)
1. Unfold pawl A and remove lens.
2. Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3. Disconnect trunk room lamp connector.
4. Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
1. Remove instrument lower driver panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket to left to release lock and remove bulb socket
(1).
3. Remove ignition key illumination bulb (2) from its socket.
4. Installation is the reverse order of removal.Vanity mirror lamp : 12V - 1.32W
PKIA7806E
Luggage room lamp : 12V - 5W
PKIA1885E
Trunk room lamp : 12V - 3.4W
PKIA0182E
Ignition key hole illumination : 12V - 1.4W
PKIC4830J

LT-172
BULB SPECIFICATIONS
Revision: 2006 November2007 350Z
BULB SPECIFICATIONSPFP:26297
HeadlampNKS00505
Exterior LampNKS00506
Interior Lamp/IlluminationNKS00507
Item Wattage (W)
High / Low35 (D2R)
Item Wattage (W)
Front combination lampFront turn signal lamp/— 28/8 (amber)
Parking lamp 5
Front side marker lamp LED
Rear combination lampStop/Tail lamp LED
Rear turn signal lamp 21 (amber)
Back-up lamp 21
Rear side marker lamp LED
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Luggage floor box lamp1.4
Cup holder illumination lamp1.1
Bottle holder illumination lampLED
Map lamp8
Luggage room lamp5
Trunk room lamp3.4
Vanity mirror lamp1.32
Ignition key hole illumination lamp1.4