keyless entry NISSAN 350Z 2007 Z33 Road Wheels And Tires Workshop Manual

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION WT
A
B
WT
Revision: 2006 November2007 350Z
ROAD WHEELS & TIRES
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Battery Service ................................ 3
Service Notice or Precautions .................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 5
NVH Troubleshooting Chart ..................................... 5
ROAD WHEEL ............................................................ 6
Inspection ................................................................. 6
ALUMINUM WHEEL ............................................. 6
STEEL WHEEL ..................................................... 6
ROAD WHEEL TIRE ASSEMBLY .............................. 7
Balancing Wheels (Bonding Weight Type) ............... 7
REMOVAL ............................................................. 7
WHEEL BALANCE ADJUSTMENT ...................... 7
Tire Rotation ............................................................. 8
DESCRIPTION ...................................................... 8
TIRE PRESSURE MONITORING SYSTEM ............. 10
System Components .............................................. 10
System Description ................................................ 10
TRANSMITTER ................................................... 10
REMOTE KEYLESS ENTRY RECEIVER ........... 10
BCM (BODY CONTROL MODULE) ..................... 11
LOW TIRE PRESSURE WARNING LAMP .......... 11
Can Communication ............................................... 12
SYSTEM DESCRIPTION .................................... 12
TROUBLE DIAGNOSIS ............................................ 13
How to Perform Trouble Diagnosis ........................ 13
BASIC CONCEPT ............................................... 13
INTRODUCTION ................................................. 13
WORK FLOW ...................................................... 14
Schematic .............................................................. 15
Wiring Diagram — T/WARN — .............................. 16
Trouble Diagnosis Chart for Symptoms ................. 19
Control Unit Input/Output Signal Standard ............. 20ID Registration Procedure ...................................... 21
ID REGISTRATION WITH ACTIVATION TOOL ... 21
ID REGISTRATION WITHOUT ACTIVATION
TOOL ................................................................... 21
Transmitter Wake Up Operation ............................. 22
WITH ACTIVATION TOOL .................................. 22
CONSULT-III Function (BCM) ................................ 22
CONSULT-III MAIN FUNCTION .......................... 22
WORK SUPPORT MODE ................................... 22
SELF-DIAG RESULTS MODE ............................ 23
DATA MONITOR MODE ...................................... 24
ACTIVE TEST MODE ......................................... 25
Diagnosis Procedure with Warning Lamp Function
(Without CONSULT-III) ........................................... 26
DESCRIPTION .................................................... 26
FUNCTION .......................................................... 26
MALFUNCTION CODE CHART .......................... 26
LOW TIRE PRESSURE WARNING LAMP
SYMPTOM CHART ............................................. 27
Preliminary Check .................................................. 29
BASIC INSPECTION ........................................... 29
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 30
Transmitter or Control Unit (BCM) .......................... 30
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 30
Transmitter - 1 ........................................................ 30
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................... 30
Transmitter - 2 ........................................................ 31
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 31
Vehicle Speed Signal .............................................. 32
MALFUNCTION CODE NO. 52 ........................... 32
TROUBLE DIAGNOSIS FOR SYMPTOMS .............. 33
Warning Lamp Does Not Come On When Ignition
Switch Is Turned On ............................................... 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Stays On When Ignition Switch Is
Turned On .............................................................. 33
DIAGNOSTIC PROCEDURE .............................. 33
Warning Lamp Blinks When Ignition Switch Is

WT-2Revision: 2006 November2007 350Z Turned On ............................................................... 35
DIAGNOSTIC PROCEDURE .............................. 35
Turn Signal Lamp Blinks When Ignition Switch Is
Turned On ............................................................... 36
DIAGNOSTIC PROCEDURE .............................. 36
ID Registration Can Not Be Completed .................. 36
DIAGNOSTIC PROCEDURE .............................. 36REMOVAL AND INSTALLATION .............................. 37
Transmitter .............................................................. 37
REMOVAL ............................................................ 37
INSTALLATION .................................................... 37
REMOTE KEYLESS ENTRY RECEIVER ............ 38
BCM (BODY CONTROL MODULE) .................... 38
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 39
Road Wheel ............................................................ 39
Tire .......................................................................... 39
Tightening Torque ................................................... 39

WT-10
TIRE PRESSURE MONITORING SYSTEM
Revision: 2006 November2007 350Z
TIRE PRESSURE MONITORING SYSTEMPFP:40300
System ComponentsNES0001A
System DescriptionNES0001B
TRANSMITTER
A sensor-transmitter (1) integrated with a valve is installed on a
wheel (2), and transmits a detected air pressure signal in the form of
a radio wave.
REMOTE KEYLESS ENTRY RECEIVER
The remote keyless entry receiver receives the air pressure signal
transmitted by the transmitter in each wheel.
SEIA0582E
: Outside
SEIA0768E
SEIA0431E

TROUBLE DIAGNOSIS
WT-19
C
D
F
G
H
I
J
K
L
MA
B
WT
Revision: 2006 November2007 350Z
Trouble Diagnosis Chart for Symptoms NES000A1
If low tire pressure warning lamp turns ON, perform self-diagnosis. Refer to WT-23, "SELF-DIAG RESULTS MODE" .
Symptom Check item Reference page
Warning lamp does not come on when ignition switch is
turned on.CAN communication line
WT-33
Combination meter
BCM
Warning lamp stays on when ignition switch is turned
on.ID registration
WT-33
BCM connector or circuit
BCM
Warning lamp blinks when ignition switch is turned on.BCM connector or circuit
WT-35
BCM
Turn signal lamp blinks when ignition switch is turned
on.BCM connector or circuit
WT-36
BCM
ID registration can not be operated.Transmitter
WT-36
Remote keyless entry receiver connector or circuit
Remote keyless entry receiver
BCM connector or circuit
BCM

WT-20
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
Control Unit Input/Output Signal StandardNES0001F
Standards using a circuit tester and oscilloscope
Te r m i n a l
(Wire color)Item ConditionVoltage (V)
Approx. value
15 (W)Tire pressure warning check con-
nectorAlways 5V
18 (B)Remote keyless entry receiver
(Ground)—0V
19 (Y)Remote keyless entry receiver
(Power supply)Stand-by
Press any of the keyfob switches
20 (L)Remote keyless entry receiver
(Signal)Stand-by
Press any of the keyfob switches
38 (W/L) Ignition switch Ignition switch ON or START Battery voltage (12V)
39 (L) Data line (CAN H) — —
40 (P) Data line (CAN L) — —
42 (GY) Battery power supply (Fuse) Always Battery voltage (12V)
45 (G/W) Turn signal (left)

Ignition switch ON

Combination switch is turn left ON
OCC3879D
OCC3882D
OCC3881D
OCC3880D
SKIA3009J

WT-30
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2006 November2007 350Z
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSPFP:00000
Transmitter or Control Unit (BCM)NES0001M
MALFUNCTION CODE NO. 21, 22, 23 OR 24
1. CHECK CONTROL UNIT

Drive for several minutes. Check all tire pressures with CONSULT-III “DATA MONITOR”.
Are all tire pressures displayed 0 kPa?
YES >> GO TO 2.
NO >> GO TO 3.
2. CHECK REMOTE KEYLESS ENTRY RECEIVER CONNECTOR
1. Disconnect remote keyless entry receiver harness connector M78.
2. Check terminals for damage or loose connection.
3. Reconnect harness connector.
OK or NG
OK >> Replace BCM refer to BCS-17, "Removal and Installation of BCM" , then GO TO 3.
NG >> Repair or replace remote keyless entry receiver harness connector.
3. ID REGISTRATION

Perform ID registration of all transmitters.
Is there any tire that ID cannot be registered to?
YES >> Replace transmitter of the tire, then GO TO 5.
NO >> GO TO 4.
4. VEHICLE DRIVING

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after vehicle speed
becomes 17 km/h (11 MPH).
Does
“DATA MONITOR” display tire pressure as normal without any warning lamp?
YES >> INSPECTION END
NO >> GO TO 5.
5. ID REGISTRATION AND VEHICLE DRIVING
1. Perform ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.
Does
“DATA MONITOR” display tire pressure as normal without any warning lamp?
YES >> INSPECTION END
NO >> GO TO the inspection applicable to DTC.
Transmitter - 1NES0001N
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48
1. ID REGISTRATION (CORRECTION OF TRANSMITTER LOCATION)
1. Perform ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
>> GO TO 2.

WT-38
REMOVAL AND INSTALLATION
Revision: 2006 November2007 350Z
3. Place wheel on turntable of tire machine. Ensure that transmitter
(1) is 270 degree from mounting head (2) when second side of
tire is fitted.
NOTE:
Do not touch transmitter at mounting head.
4. Lubricate tire well and fit second side of tire as normal. Ensure that tire does not rotate relative to rim.
5. Inflate tire and fit to appropriate wheel position.
REMOTE KEYLESS ENTRY RECEIVER
Removal
1. Remove the front kicking plate LH. Refer to EI-35, "BODY SIDE TRIM" .
2. Remove the dash side finisher LH. Refer to EI-35, "
BODY SIDE TRIM" .
3. Remove the instrument lower cover. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
4. Remove the glove box assembly. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
5. Disconnect keyless entry receiver connector.
Installation
Install in the reverse order of removal.
BCM (BODY CONTROL MODULE)
Removal
Remove the BCM. Refer to BCS-17, "Removal and Installation of BCM" .
Installation
Install in the reverse order of removal.
SEIA0797E