air condition NISSAN 350Z 2007 Z33 Roof Owner's Guide

SOFT TOP
RF-73
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
3. CHECK 5TH BOW HALF-LATCH SWITCH GROUND CIRCUIT
Check continuity between soft top lock switch connector T205 terminal 6 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 31 and ground.
OK or NG
OK >> Replace 5th bow lock assembly in storage lid.
NG >> Replace soft top control unit.
Check 5th Bow Full-Latch SwitchNIS0007B
1. CHECK 5TH BOW FULL-LATCH SWITCH SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top lock switch (5th bow full-latch switch) is OK.
NG >> GO TO 2.6 (B) - Ground : Continuity should exist.
PIIA7899E
31 (L) - Ground : Approx. 5V
PIIA7897E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 30 (Y/R) Ground CL10 0 → 5
PIIA7933E

SOFT TOP
RF-75
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check 5th Bow Ending SwitchNIS0007C
1. CHECK 5TH BOW ENDING SWITCH SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top lock switch (5th bow ending switch) is OK.
NG >> GO TO 2.
2. CHECK 5TH BOW ENDING CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and soft top lock switch (at 5th bow lock assembly in storage lid) connec-
tor.
3. Check continuity between soft top control unit connector B67
terminal 29 and soft top lock switch connector T205 terminal 1.
4. Check continuity between soft top control unit connector B67
terminal 29 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK 5TH BOW ENDING SWITCH GROUND CIRCUIT
Check continuity between soft top lock switch connector T205 terminal 2 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 29 (R/Y) Ground CL10 0 → 5
PIIA7936E
29 (R/Y) - 1 (R) : Continuity should exist.
29 (R/Y) - Ground : Continuity should not exist.
PIIA7937E
2 (B) - Ground : Continuity should exist.
PIIA7938E

RF-76
SOFT TOP
Revision: 2006 November2007 350Z
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 29 and ground.
OK or NG
OK >> Replace soft top lock switch (5th bow lock assembly in
storage lid).
NG >> Replace soft top control unit.
Check 5th Bow Closure MotorNIS0007D
1. 5TH BOW CLOSURE MOTOR INPUT SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between 5th bow closure motor connector and ground.
OK or NG
OK >> Replace 5th bow closure motor.
NG >> GO TO 2.
2. CHECK 5TH BOW CLOSURE MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and 5th bow closure motor connector.
3. Check continuity between soft top control unit connector B66
terminal 4, 12 and 5th bow closure motor connector T204 termi-
nal 1, 2.
4. Check continuity between soft top control unit connector B66
terminal 4, 12 and ground.
OK or NG
OK >> Replace soft top control unit.
NG >> Repair or replace harness.29 (R/Y) - Ground : Approx. 5V
PIIA7936E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
T204 1 (W) Ground CL9 → CL10 0 → Battery voltage → 0
PIIA7939E
4 (G/R) - 1 (W) : Continuity should exist.
12 (G/Y) - 2 (G) : Continuity should exist.
4 (G/R) - Ground : Continuity should not exist.
12 (G/Y) - Ground : Continuity should not exist.
PIIA7940E

SOFT TOP
RF-77
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check Soft Top Front Lock SwitchNIS001L7
1. SOFT TOP FRONT LOCK SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top front lock switch is OK.
NG >> GO TO 2.
2. CHECK 5TH BOW ENDING CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and soft top front lock switch connector.
3. Check continuity between soft top control unit connector B67
terminal 28 and soft top front lock switch connector R8 terminal
4.
4. Check continuity between soft top control unit connector B67
terminal 28 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK SOFT TOP FRONT LOCK SWITCH GROUND CIRCUIT
Check continuity between soft top front lock switch connector R8 terminal 3 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
ConnectorTerminal (Wire color)
ConditionVoltage (V)
(Approx.)
(+) (-)
B67 28 (LG/B) GroundFront
lockLock 5
Unlock 0
PIIB7354E
28 (LG/B) - 4 (LG/B) : Continuity should exist.
28 (LG/B) - Ground : Continuity should not exist.
PIIB7355E
3 (B/W) - Ground : Continuity should exist.
PIIB7356E

RF-80
SOFT TOP
Revision: 2006 November2007 350Z
5. CHECK BRAKE PEDAL SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and stop lamp switch connector.
3. Continuity between soft top control unit connector B68 terminal
38 and stop lamp switch connector E111 terminal 4.
4. Continuity between soft top control unit connector B68 terminal
38 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness.
6. CHECK STOP LAMP SWITCH
Continuity between stop lamp switch connector E111 terminal 3 and 4.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace stop lamp switch.
Check Each Switch Condition (Open Operate)NIS0007F
1. CHECK EACH SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Each switch condition is OK.
NG >> Check malfunction switch.38 (W) - 4 (P/L) : Continuity should exist.
38 (W) - Ground : Continuity should not exist.
PIIB7357E
Connector Terminal Brake pedal condition Continuity
E 111 3 4Depressed Yes
Released No
PIIB7358E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B6720 (W/B)
Ground Full closed 5 21 (W/L)
22 (W/R)
24 (G)
25 (L/Y)
26 (LG)
27 (GY)
32 (W)
33 (BR)
PIIA7949E

SOFT TOP
RF-83
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check Passenger Side Seat Operate Signal 2NIS0007K
1. CHECK PASSENGER SIDE SEAT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit, storage lid actuator RH and passenger seat control unit connector.
3. Check continuity between soft top control unit connector B66
terminal 13 and passenger seat control unit connector B354 ter-
minal 33.
4. Check continuity between soft top control unit connector B66
terminal 13 and ground.
OK or NG
OK >> Replace passenger seat control unit.
NG >> Repair or replace harness.
Check Passenger Side Seat Operate Signal 3NIS0007L
1. CHECK PASSENGER SIDE SEAT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit, passenger seat control unit and soft top lock switch connector.
3. Check continuity between passenger seat control unit connector
B353 terminal 11 and soft top control unit connector B67 termi-
nal 30.
4. Check continuity between soft top control unit connector B67
terminal 30 and ground.
OK or NG
OK >> Replace passenger seat control unit.
NG >> Repair or replace harness.
Check Seat Back Position SignalNIS0007M
1. CHECK SEAT BACK POSITION SIGNAL
1. Start engine.
2. The thing whose seat cancel switch is OFF is confirmed.
3. Soft top switch operate, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Replace soft top control unit.
NG >> GO TO 2.13 (L/R) - 33 (G/B) : Continuity should exist.
13 (L/R) - Ground : Continuity should not exist.
PIIA7959E
11 (L/W) - 30 (Y/R) : Continuity should exist.
11 (L/W) - Ground : Continuity should not exist.
PIIB9257E
ConnectorTerminal (Wire color)
Seat conditionVoltage (V)
(Approx.)
(+) (-)
B67 34 (L/W) GroundWhen passenger seat
inclines forward5
Other than above 0
PIIA7961E

RF-84
SOFT TOP
Revision: 2006 November2007 350Z
2. CHECK SEAT BACK POSITION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and passenger seat control unit connector.
3. Check continuity between soft top control unit connector B67
terminal 34 and passenger seat control unit connector B353 ter-
minal 32.
4. Check continuity between soft top control unit connector B67
terminal 34 and ground.
OK or NG
OK >> Check passenger side seat. Refer to SE-37, "Trouble
Diagnosis Symptom Chart" .
NG >> Repair or replace harness.
Check Speed Signal CircuitNIS0007N
First perform the “SELF-DIAG RESULT” in “BCM” with CONSULT-II, then perform the each trouble diagnosis
of malfunction system indicated “SELF-DIAG RESULT” of “BCM”. Refer to BCS-15, "
CONSULT-III Function
(BCM)" .
1. CHECK VEHICLE SPEED SIGNAL
1. Start engine.
2. Check the signal between soft top control unit connector and ground with oscilloscope.
OK or NG
OK >> Replace soft top control unit.
NG >> GO TO 2.34 (L/W) - 32 (G/W) : Continuity should exist.
34 (L/W) - Ground : Continuity should not exist.
PIIA7962E
ConnectorTerminal (Wire
color)
ConditionSignal
(Reference value.)
(+) (-)
B66 14 (W)
GroundSpeedometer
operated
[When
vehicle speed
is Approx.
40km/h
(25MPH)]
B67 23 (W/G)
PIIA7941EPKIA1935E
PIIB0078J

SOFT TOP
RF-85
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
2. CHECK VEHICLE SPEED SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and unified meter and A/C amp connector.
3. Check the following.
–Continuity between soft top control unit connector B66 terminal
14 and unified meter and A/C amp connector M49 terminal 26.
–Continuity between soft top control unit connector B66 terminal
14 and ground.
4. Check the following.
–Continuity between soft top control unit connector B67 terminal
23 and unified meter and A/C amp connector M49 terminal 34.
–Continuity between soft top control unit connector B67 terminal
23 and ground.
OK or NG
OK >> Check unified meter and A/C amp. Refer to DI-44, "Sys-
tem Description" .
NG >> Repair or replace harness.
Check Indicator Lamp CircuitNIS0007O
1. CHECK FUSE

Check 10A fuse [No.14, located in fuse block (J/B)]
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK INDICATOR LAMP SIGNAL
1. Start engine.
2. Soft top switch operate, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Check the condition of the harness and the connector.
NG - 1 >> If battery voltage: Replace soft top control unit.
NG - 2 >> If 0V: GO TO 3.14 (W) - 26 (W) : Continuity should exist.
14 (W) - Ground : Continuity should not exist.
PIIA7942E
23 (W/G) - 34 (L) : Continuity should exist.
23 (W/G) - Ground : Continuity should not exist.
PIIA7943E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 35 (Y) GroundFull open or full close Battery voltage
Other than above 0
PIIB0835E

RF-86
SOFT TOP
Revision: 2006 November2007 350Z
3. CHECK INDICATOR LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and combination meter connector.
3. Check continuity between soft top control unit connector B67
terminal 35 and combination meter connector M19 terminal 13.
4. Check continuity between soft top control unit connector B67
terminal 35 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK INDICATOR LAMP POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between combination meter connector M19 ter-
minal 23 and ground.
OK or NG
OK >> Check the Condition of the Harness and the Connector.

If OK: Replace combination meter.

If NG: Repair or replace harness.
NG >> Repair or replace harness.
Removal and Installation of Soft Top Control UnitNIS0007P
REMOVAL
1. Push the soft top switch on the close side to clear the soft top storage room, and release the buttom
before strage lid starts closing.
2. Remove trim parts and turn the front side of storage room finisher. RF-126, "
Removal and Installation of
Storage Room Finisher"
3. Disconnect soft top control unit connector, remove the screw
and soft top control unit.
INSTALLATION
Installation in the reverse order of removal.35 (Y) – 13 (G/W) : Continuity should exist.
35 (Y) – Ground : Continuity should not exist.
PIIB0836E
23 (G/Y) – Ground : Battery voltage
PIIB0837E
PIIB0838E