turn signal NISSAN 350Z 2007 Z33 Roof Workshop Manual

SOFT TOP
RF-13
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
CONDITIONS FOR OPERATION
Operation is avairable when all of the conditions below are satisfied.

Ignition switch is ON.

The brake pedal is ON.

Vehicle speed is 4 km/h (2 MPH) or less.

Battery voltage is approximately 10 V or more.
CAUTION:
Run the engine when operating or inspecting the soft top to prevent battery dies.
CONDITIONS FOR STOPPING OPERATION
Operation of the soft top stops when the conditions below are satisfied while the soft top is operating.

Any of the above operation conditions is no longer satisfied.

The passenger side power seat is operated. (It does not move when seat cancel switch is ON.)
OUTLINE OF OPERATION
Refer to the illustrations for the positions of the soft top, and the conditions of switch and actuator operation.
OPERATION: FULL CLOSE → FULL OPEN
Refer to RF-19, "State Chart" .

CONDITION: FULL CLOSE

CONDITION: OP 1
When the soft top switch is pushed to OPEN, the indicator lamp illuminates, windows activate to the fully-
open position and the passenger seat tilts forward by approximately 6 degrees by power window down
request signal. When passenger seat tilts forward by approximately 6 degrees, seat back position signal is
turned ON.

CONDITION: OP 2
The 5th bow unlock actuator operates, releasing the 5th bow lock.
Item Condition
5th bow half-latch switch : OFF
5th bow full-latch switch : OFF
5th bow ending switch : OFF
5th bow full open detection switch : OFF
5th bow full close detection switch : OFF
Storage lid full open detection switch : OFF
Storage lid full close detection switch LH : OFF
Storage lid full close detection switch RH : OFF
Roof full open detection switch : OFF
Roof full close detection switch : OFF
Body interference prevention switch : OFF
Roll bar interference prevention switch : OFF
Item Condition
Soft top switch : OPEN (Until the operation ends)
Indicator lamp : ON
Power window down request signal : ON
Seat back position signal : OFF → ON
Item Condition
5th bow unlock actuator : ON

SOFT TOP
RF-15
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z

CONDITION: OP 9
While the roof is opening, the 5th bow actuator moves the 5th bow up.

CONDITION: OP 10
While the roof is opening, the 5th bow stops in the fully-open position.

CONDITION: OP 11
The roof is stored and stops motion. The storage lid actuator operates (DOWN operation) to lower the
storage lid.
The passenger seat also returns to its original position.

CONDITION: OP 12
At the fully-closed position, the storage lid inverts and stops. The passenger seat tilts back. Opening oper-
ation is completed, and the indicator lamp turns OFF.
Item Condition
Roof actuator (LH and RH) : OPEN
5th bow actuator : UP
5th bow full close detection switch : OFF → ON
Roll bar interference prevention switch : OFF → ON
Item Condition
Roof actuator (LH and RH) : OPEN
5th bow full open detection switch : OFF → ON
5th bow actuator : UP → STOP
Body interference prevention switch : OFF → ON
Item Condition
Roof full open detection switch : OFF → ON
Roof actuator (LH and RH) : OPEN → STOP
Storage lid actuator (LH and RH) : CLOSE
Storage lid full open detection switch : ON → OFF
Storage lid full close detection switch (LH) : ON → OFF
Power window request signal : OFF
Item Condition
Storage lid full close detection switch (RH) : ON → OFF
Storage lid actuator (LH and RH) : CLOSE → OPEN → STOP
Indicator lamp : ON → OFF

RF-16
SOFT TOP
Revision: 2006 November2007 350Z
OPERATION: FULL OPEN → FULL CLOSE
Refer to RF-21, "State Chart" .

CONDITION: FULL OPEN

CONDITION: CL 1
When the soft top switch is pressed to the CLOSE side, the indicator lamp illuminates, storage lid unlock
actuator also operates, releasing the storage lid lock.

CONDITION: CL 2
Windows activate to the fully-open position and the passenger seat tilts forward by approximately 6
degrees by power window down request signal. Storage lid actuator operates to raise the storage lid.
When passenger seat tilts forward by approximately 6 degrees, seat back position signal is turned ON.

CONDITION: CL 3
The storage lid stops at the fully-open position. The roof actuator operates (CLOSE operation) to close the
roof.
Item Condition
5th bow half-latch switch : ON
5th bow full-latch switch : ON
5th bow ending switch : ON
5th bow full open detection switch : ON
5th bow full close detection switch : ON
Storage lid full open detection switch : OFF
Storage lid full close detection switch LH : OFF
Storage lid full close detection switch RH : OFF
Roof full open detection switch : ON
Roof full close detection switch : ON
Body interference prevention switch : ON
Roll bar interference prevention switch : ON
Item Condition
Soft top switch : OLOSE (Until the operation ends)
Indicator lamp : ON
Storage lid unlock actuator : ON
Storage lid full close detection switch (RH) : OFF → ON
Item Condition
Storage lid full close detection switch (LH) : OFF → ON
Storage lid actuator (LH and RH) : UP
Power window down request signal : ON
Storage lid unlock actuator : ON → OFF
Seat back position signal : OFF → ON
Item Condition
Storage lid full open detection switch : OFF → ON
Storage lid actuator (LH and RH) : OPEN → STOP
Roof actuator (LH and RH) : CLOSE
Roof full open detection switch : ON → OFF
Body interference prevention switch : ON → OFF

RF-18
SOFT TOP
Revision: 2006 November2007 350Z

CONDITION: CL 10
5th bow auto closure operates. The passenger seat tilts back. Closing operation is completed, soft top
front lock is locked, and the indicator lamp turns OFF. The passenger seat also returns to its original posi-
tion.
Item Condition
5th bow actuator : DOWN → STOP
5th bow half-latch switch : ON → OFF
5th bow full-latch switch : ON → OFF
5th bow ending switch : ON → OFF
5th bow closure motor : CLOSE → STOP
Power window request signal : OFF
Indicator lamp : ON → OFF

SOFT TOP
RF-23
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Indicator LampNIS0006E
The indicator lights, turns off or blinks according to the operating state.
*: The soft top operates for approximately 30 seconds after turn ignition switch OFF.
Turns OFF : The open / close operation stops or completes or any switch is malfunctioning
Lights : The soft top is operating or the operation stops on the way
Blinks : The soft top cannot be operated, do not response or front lock is unlocked at
the fully closed position
State of roofThe operation stops when the soft top is,
Operation
full open or
full closein position on
the way
Operational condition Turning off Lighting Lighting
Out of operational
conditionWhen battery voltage decreases remarkably Turning off Lighting Lighting
Brake pedal is not depressed Turning off Lighting Lighting
Vehicle speed is 5 km/h (3 MPH) or more Turning off Lighting Lighting
Ignition switch: OFF Turning off Turning off* Turning off*
Malfunction ofany switch of the system Turning off Lighting Blinking
soft top control unit Blinking Blinking Blinking
vehicle speed signal Blinking Blinking Blinking

SOFT TOP
RF-37
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Work FlowNIS0006I
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to RF-12, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to RF-37,
"Trouble Diagnosis Chart by Symptom" .
4. Does soft top system operate normally? If Yes, GO TO 5. If No, GO TO 3.
5. INSPECTION END.
Trouble Diagnosis Chart by SymptomNIS0006J
(CLOSE → OPEN)
The operation chart for roof position. Refer to RF-19, "State Chart" .
48 Y/BStorage lid actuator LH
(CLOSE) signalOutputCL7 → CL8 0 → Battery voltage → 0
Other than above 0 Te r m i -
nal No.Wire
colorDescription
Condition
(Roof position: CL)Va l u e ( V )
(Approx.)
Signal name Input/
Output
Symptom Diagnostic procedure and repair order Roof position Refer to page
Roof does not operate1. Check soft top control unit power supply OP1RF-40
2. Check soft top switch (Open) OP1RF-40
3. Check operation permission condition OP1RF-78
4. Check each switch condition (Open operate) Full closeRF-80
5. Check seat back position signal OP1RF-83
6. Check 5th bow unlock actuator (Open operate) OP2RF-44
7. Check 5th bow half-latch switch (Open operate) OP2RF-44
8. Check 5th bow actuator (Open operate) OP3RF-46
5th bow operation stops at full
open position1. Check 5th bow full close detection switch
(Open operate)OP4RF-46
2. Check 5th bow full open detection switch
(Open operate)OP5RF-48
3. Check storage lid unlock actuator
(Open operate)OP5RF-49
4. Check storage lid full close detection switch (LH
and RH) (Open operate)OP5.6RF-50
5. Check storage lid actuator (Open operate) OP6RF-52
Storage lid operation stops at
full open positionCheck storage lid full open detection switch (Open
operate)OP7RF-53
Roof does not operate Check roof actuator (Open operate) OP8RF-55
Roof stops on the wayCheck roll bar interference prevention switch
(Open operate)OP8RF-56
Storage lid operation stops at
full open position after the roof
is stored.1. Check body interference prevention switch
(Open operate)OP10RF-57
2. Check roof full open detection switch OP10RF-58
Passenger side seat back does
not operate.1. Check passenger side seat cancel switch OP1SE-52
2. Check passenger side seat operate signal 1 OP1RF-82
Passenger side seat bock does
not return to former stateCheck passenger side seat operate signal 2 OP10RF-83
Power window down does
not operate.Check power window harness OP1RF-82

RF-38
SOFT TOP
Revision: 2006 November2007 350Z
(OPEN → CLOSE)
The operation chart for roof position. Refer to RF-21, "State Chart" .
Both power window down and
passenger seat are not oper-
ated.Check power window down request signal OP1RF-81
Indicator lamp does not light.
(soft top operates properly)Check indicator lamp circuit —RF-85
Indicator lamp blinks when IGN
SW: OFF → ON is done.Replace soft top control unit —RF-86
Indicator lamp blinks when
beginning to run.Check speed signal —RF-84
Symptom Diagnostic procedure and repair order Roof position Refer to page
Symptom Diagnostic procedure and repair order Roof position Refer to page
Roof does not operate1. Check soft top control unit power supply CL1RF-40
2. Check soft top switch (Close) CL1RF-42
3. Check operation permission condition CL1RF-78
4. Check each switch condition (Close operate) Full openRF-81
5. Check seat back position signal CL1RF-83
6. Check storage lid unlock actuator
(Close operate)CL1RF-59
7. Check storage lid full close detection switch
(LH and RH) (Close operate)CL1.2RF-60
8. Check storage lid actuator (Close operate) CL2RF-62
Storage lid operation stops at
full open position1. Check roof actuator (Close operate) CL2RF-662. Check body interference prevention switch
(Close operate)CL3RF-65
Roof stops on the way1. Check storage lid full open detection switch
(Close operate)CL3RF-632. Check roof full close detection switch
(Close operate)CL5RF-67
3. Check 5th bow actuator (Close operate) CL5RF-69
Operation stops after 5th
bow operates downCheck 5th bow full close detection switch
(Close operate)CL5RF-69
Operation stops after 5th
bow operates upCheck 5th bow full open detection switch
(Close operate)CL6RF-71
Auto closure of 5th bow does
not operate.1. Check 5th bow half-latch switch CL10RF-722. Check 5th bow full-latch switch CL10RF-73
3. Check 5th bow ending switch CL10RF-75
4. Check 5th bow closure motor CL10RF-76
Passenger side seat back does
not operate.1. Check passenger side seat cancel switch CL1SE-52
2. Check passenger side seat operate signal 1 CL1RF-82
Passenger side seat back does
not return to former stateCheck passenger side seat operate signal 3 CL10RF-83
Power window down does
not operate.Check power window harness CL1RF-82
Both power window down and
passenger seat are not oper-
ated.Check power window down request signal CL1RF-81
Indicator lamp does not light.
(soft top operates properly)Check indicator lamp circuit —RF-85

RF-40
SOFT TOP
Revision: 2006 November2007 350Z
Check Soft Top Control Unit Power Supply (OP, CL)NIS0006K
1. CHECK FUSE

Check 10A fuse [No.12, located in the fuse block (J/B)]

Check 40A fusible link (letter G located in the fuse and fusible link box.)
NOTE:
Refer to RF-11, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-4, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Start engine.
2. Check voltage between soft top control unit connector B66, 67
terminal 1, 8, 17 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check soft top control unit power supply circuit for open
or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit connector.
3. Check continuity between soft top control unit connector B66
terminal 7, 16 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check soft top control unit ground circuit for open or
short.
Check Soft Top Switch (OPEN)NIS0006L
1. CHECK SOFT TOP OPEN SWITCH SIGNAL
1. Start engine.
2. Check soft top control unit connector and ground.
OK or NG
OK >> Soft top switch (OPEN) is OK.
NG >> GO TO 2.1 (W/R) - Ground : Battery voltage
8 (W/R) - Ground : Battery voltage
17 (R) - Ground : Battery voltage
PIIA7886E
7 (B) - Ground : Continuity should exist.
16 (B) - Ground : Continuity should exist.
PIIA7887E
ConnectorTerminal (Wire color)
Soft top switch
ConditionVoltage (V)
(Approx.)
(+) (-)
B67 18 (SB) GroundOPEN 0
Other than above 5
PIIA7888E

RF-42
SOFT TOP
Revision: 2006 November2007 350Z
5. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 18 and ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace soft top control unit.
Check Soft Top Switch (CLOSE)NIS0006M
1. CHECK SOFT TOP CLOSE SWITCH SIGNAL
1. Start engine.
2. Check soft top control unit connector and ground.
OK or NG
OK >> Soft top switch (CLOSE) is OK.
NG >> GO TO 2.
2. CHECK SOFT TOP SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top switch connector.
3. Check continuity between soft top switch connector M14 termi-
nal 1 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.18 (SB) - Ground : Approx. 5V
PIIA7888E
ConnectorTerminal (Wire color)
Soft top
switch ConditionVoltage (V)
(Approx.)
(+) (-)
B67 19 (R/W) GroundCLOSE 0
Other than above 5
PIIA7892E
1 (B) - Ground : Continuity should exist.
PIIA7889E

RF-44
SOFT TOP
Revision: 2006 November2007 350Z
Check 5th Bow Unlock Actuator (Open Operate)NIS0006N
1. CHECK 5TH BOW UNLOCK ACTUATOR SIGNAL
1. Start engine.
2. Operate soft top switch OPEN, check voltage between soft top
control unit connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace soft top control unit.
2. CHECK 5TH BOW UNLOCK ACTUATOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect 5th bow unlock actuator connector.
3. Check continuity between 5th bow unlock actuator connector
T203 terminal 1 and ground.
OK or NG
OK >> Replace 5th bow unlock actuator.
NG >> Repair or replace harness.
Check 5th Bow Half-Latch Switch (Open Operate)NIS0006O
1. CHECK 5TH BOW HALF-LATCH SWITCH SIGNAL CHECK
1. Start engine.
2. Operate soft top switch OPEN, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top lock switch (5th bow half-latch switch) is OK.
NG >> GO TO 2.
Con-
nectorTerminal (Wire color)
Roof ConditionVoltage (V)
(Approx.)
(+) (-)
B66 6 (R) Ground OP1 → OP2 0 → Battery voltage
PIIA7895E
1 (B) - Ground : Continuity should exist.
PIIA7896E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 31 (L) Ground OP2 → OP3 5 → 0
PIIA7897E