ignition NISSAN 350Z 2007 Z33 Wiper, Washer And Horn Owner's Manual

WW-44
REAR WIPER AND WASHER SYSTEM
Revision: 2006 November2007 350Z
2. ACTIVE TEST
CONSULT-III ACTIVE TEST
1. Select "REAR WIPER" of BCM active test item.
2. With operating the test item, check that rear wiper operation.
GO TO 3
Does rear wiper operate normally?
YES >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NO >> GO TO 3.
3. CHECK BCM
With rear wiper switch ON, check voltage between rear wiper motor
harness connector and ground.
OK or NG
OK >> GO TO 4.
NG >> GO TO 5.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear wiper motor connector.
3. Check continuity between rear wiper motor harness connector
and ground.
OK or NG
OK >> Replace rear wiper motor. Refer to WW-47, "Removal
and Installation of Rear Wiper Motor" .
NG >> Repair harness or connector.
Te r m i n a l s
Voltag e
(Approx.) (+) (-)
Rear wiper motor
connectorTe r m i n a l
Ground
D106 4 Battery voltage
PKIB1784E
Rear wiper motor
connectorTe r m i n a l
Ground Continuity
D106 1 Yes
PKIA7055E

REAR WIPER AND WASHER SYSTEM
WW-45
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2006 November2007 350Z
5. CHECK REAR WIPER CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and rear wiper motor connector.
3. Check continuity between BCM harness connector and rear
wiper motor harness connector.
4. Check continuity between BCM harness connector and ground.
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> Repair harness or connector.
Rear Wiper Does Not Return to Stop PositionNKS00535
1. CHECK REAR WIPER MOTOR CIRCUIT
With CONSULT-III
1. Select "RR WIPER STOP" of BCM data monitor item.
2. Make sure that “RR WIPER STOP”, turn ON-OFF linked with rear wiper switch operation.
GO TO 2
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> GO TO 2.
2. CHECK REAR WIPER AUTO STOP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and rear wiper motor connector.
3. Check continuity between BCM harness connector and rear
wiper motor harness connector.
4. Check continuity between BCM harness connector and ground.
5. Check continuity between rear wiper motor harness connector
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
BCM Rear wiper motor
Continuity
Connector Terminal Connector Terminal
B83 70 D106 4 Yes
BCM connector Terminal
Ground Continuity
B83 70 No
PKIB5177E
BCM Rear wiper motor
Continuity
Connector Terminal Connector Terminal
B83 59 D106 2 Yes
BCM connector Terminal
Ground Continuity
B83 59 No
PKIB5178E
Rear wiper motor
connectorTerminal
Ground Continuity
D106 1 Yes
PKIA7057E

WW-46
REAR WIPER AND WASHER SYSTEM
Revision: 2006 November2007 350Z
3. CHECK REAR WIPER MOTOR SIGNAL
1. Connect BCM connector and rear wiper motor connector.
2. Turn ignition switch ON.
3. Check voltage between rear wiper motor harness connector ter-
minal and ground while rear wiper motor is stopped and while it
is operating.
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> Replace rear wiper motor. Refer to BCS-17, "
Removal and Installation of BCM" .
Only Rear Wiper ON Does Not OperateNKS00536
Refer to LT- 9 2 , "Combination Switch Inspection" .
Only Rear Wiper INT Does Not OperateNKS00537
Refer to LT- 9 2 , "Combination Switch Inspection" .
Wiper Does Not Wipe When Rear Washer OperatesNKS00538
Refer to LT- 9 2 , "Combination Switch Inspection" .
Rear Wiper Does Not StopNKS00539
1. CHECK CIRCUIT BETWEEN COMBINATION SWITCH AND BCM
With CONSULT-III
1. Select “BCM” on CONSULT-III, and select “WIPER” on “SELECT TEST ITEM” screen.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen. Make sure that “RR WIPER INT”, “RR
WIPER ON”, and “RR WASHER SW” turn ON-OFF according to wiper switch operation.
Without CONSULT-III
Refer to LT- 9 2 , "
Combination Switch Inspection" .
OK or NG
OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM" .
NG >> Check combination switch (wiper switch). Refer to LT- 9 2 , "
Combination Switch Inspection" .
Removal and Installation of Rear Wiper Arm, Adjustment of Wiper Arms Stop
Location
NKS0053A
REMOVAL
1. Turn rear wiper switch ON to operate wiper motor, and then turn rear wiper switch OFF (auto stop).
2. Remove rear wiper arm cap, and remove rear wiper arm nut.
3. Raise rear wiper arm, and remove rear wiper arm from the vehicle.
Terminals
ConditionVoltag e
(Approx.) (+)
(-)
Rear wiper motor
connectorTerminal
D106 2 GroundWiper stopped Battery voltage
Wiper operating 0 V
PKIA7058E