Engine NISSAN ALMERA 2001 Service Manual

SCL466-C
CLUTCH COVERNJCL0032S02+Check clutch cover installed on vehicle for unevenness of dia-
phragm spring toe height.
Uneven limit:
MODEL 200, 215 0.8 mm (0.031 in)
MODEL 240 0.7 mm (0.028 in)
+If out of limit, adjust the height with Tool.
AEM100
FLYWHEELNJCL0032S03+Check contact surface of flywheel for slight burns or discolora-
tion. Repair flywheel with emery paper.
+Check flywheel runout.
Maximum allowable runout:
Refer to EM-62, ªFlywheel/Drive Plate Runoutº (QG
engine models), and EM-154, ªFlywheel Runout (YD
engine models)º.
SCL616-B
SCL600-F
InstallationNJCL0033+Insert Tool into clutch disc hub when installing clutch cover and
disc.
+Be careful not to allow grease to contaminate clutch fac-
ing.
+Tighten bolts in numerical order.
First step:
: 10 - 20 N´m (1 - 2 kg-m,7-14ft-lb)
Final step:
QG engine models (200, 215)
: 22 - 29 N´m (2.2 - 3.0 kg-m, 15 - 21 ft-lb)
YD22DDT engine model (240)
: 35 - 44 N´m (3.5 - 4.5 kg-m, 26 - 32 ft-lb)
CLUTCH DISC, CLUTCH COVER AND FLYWHEEL
Inspection and Adjustment (Cont'd)
CL-23

Clutch Control SystemNJCL0034
Type of clutch controlHydraulic
Clutch Master CylinderNJCL0035Unit: mm (in)
Inner diameter15.87 (5/8)
Clutch Operating CylinderNJCL0036Unit: mm (in)
Inner diameter19.05 (3/4)
Clutch DiscNJCL0038Unit: mm (in)
Engine QG15DE QG18DE YD22DDT
Model 200215
240
Part number 30100-2F205 Part number 30100-2F215
Facing size (Outer dia.´
inner dia.´thickness)200´134´3.5 (7.87´
5.28´0.138)215´140´3.5 (8.46´
5.51´0.138)216´153´3.45 (8.50´
6.02´0.1358)240´160´3.5 (9.45´
6.30´0.138)
Thickness of disc assembly
with load7.4 - 8.0 (0.291 - 0.315)
with 3,780 N (385.6 kg,
849.7 lb)7.6 - 8.0 (0.299 - 0.315)
with 4,904 N (500 kg, 1,103
lb)7.3 - 7.9 (0.2874 - 0.310)
with 4,900 N (499.8 kg,
1,102 lb)7.85 - 8.35 (0.3091 -
0.3287) with 5,690 N (580.2
kg, 1,279 lb)
Wear limit of facing surface
to rivet head0.3 (0.012) 0.3 (0.012) Ð 0.3 (0.012)
Wearing thickness of facing Ð Ð 1.3 (0.051) Ð
Runout limit of facing 1.0 (0.039)
Distance of runout check
point (from the hub center)95 (3.74) 102.5 (4.04) 115 (4.53)
Maximum backlash of
spline (at outer edge disc)0.8 (0.031) 0.9 (0.035) 1.0 (0.039)
Clutch CoverNJCL0039Unit: mm (in)
Engine QG15DE QG18DE YD22DDT
Model 200 215 240
Full-load 3,481 N (355 kg, 783 lb) 4,413 N (450 kg, 992 lb) 5,690 N (580.2 kg, 1,279 lb)
Uneven limit of diaphragm spring
toe height0.8 (0.031) 0.7 (0.028)
Clutch PedalNJCL0040Unit: mm (in)
Applied modelSedan
Hatchback
QG15DE YD22DDT QG18DE
Pedal height ªSº138 - 148
(5.43 - 5.83)138 - 148
(5.43 - 5.83)134 - 144
(5.28 - 5.67)140 - 150
(5.51 - 5.91)
Pedal free play ªAº1 - 3 (0.039 - 0.118)
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch Control System
CL-24

ENGINE CONTROL SYSTEM
SECTION
EC
CONTENTS
QG
TROUBLE DIAGNOSIS - INDEX..................................10
Alphabetical & P No. Index for DTC .........................10
PRECAUTIONS.............................................................16
Supplemental Restraint System (SRS)²AIR
BAG²and²SEAT BELT PRE-TENSIONER².............16
Precautions for On Board Diagnostic (OBD)
System of Engine and A/T.........................................16
Engine Fuel & Emission Control System ..................17
Wiring Diagrams and Trouble Diagnosis ...................19
PREPARATION.............................................................20
Special Service Tools ................................................20
Commercial Service Tools .........................................20
ENGINE AND EMISSION CONTROL OVERALL
SYSTEM.........................................................................21
Engine Control Component Parts Location ...............21
Circuit Diagram ..........................................................25
System Diagram ........................................................29
Vacuum Hose Drawing ..............................................30
System Chart .............................................................31
ENGINE AND EMISSION BASIC CONTROL
SYSTEM DESCRIPTION...............................................32
Multiport Fuel Injection (MFI) System .......................32
Electronic Ignition (EI) System ..................................34
Air Conditioning Cut Control ......................................35
Fuel Cut Control (at no load & high engine
speed) ........................................................................36
Evaporative Emission System ...................................36
Positive Crankcase Ventilation ..................................39
BASIC SERVICE PROCEDURE...................................40
Fuel Pressure Release ..............................................40
Fuel Pressure Check .................................................40
Fuel Pressure Regulator Check ................................41
Injector .......................................................................41
How to Check Idle Speed and Ignition Timing ..........43
Preparation ................................................................44
Inspection Procedure .................................................47
Idle Air Volume Learning ...........................................57ON BOARD DIAGNOSTIC SYSTEM
DESCRIPTION...............................................................59
Introduction ................................................................59
Two Trip Detection Logic ...........................................59
Emission-related Diagnostic Information ...................60
NATS (Nissan Anti-theft System) ..............................74
Malfunction Indicator (MI) ..........................................74
OBD System Operation Chart (With Euro-OBD
Models Only)..............................................................78
CONSULT-II ...............................................................83
Generic Scan Tool (GST) ..........................................94
TROUBLE DIAGNOSIS - INTRODUCTION..................96
Introduction ................................................................96
Work Flow ..................................................................98
TROUBLE DIAGNOSIS - BASIC INSPECTION.........100
Basic Inspection/Sedan ...........................................100
Basic Inspection/Hatchback.....................................128
TROUBLE DIAGNOSIS - GENERAL
DESCRIPTION.............................................................153
DTC Inspection Priority Chart..................................153
Fail-safe Chart .........................................................154
Symptom Matrix Chart .............................................155
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................159
Major Sensor Reference Graph in Data Monitor
Mode ........................................................................161
ECM Terminals and Reference Value .....................164
TROUBLE DIAGNOSIS - SPECIFICATION VALUE..173
Description ...............................................................173
Testing Condition .....................................................173
Inspection Procedure ...............................................173
Diagnostic Procedure ..............................................174
TROUBLE DIAGNOSIS FOR INTERMITTENT
INCIDENT.....................................................................177
Description ...............................................................177
Diagnostic Procedure ..............................................177
TROUBLE DIAGNOSIS FOR POWER SUPPLY........178
Main Power Supply and Ground Circuit ..................178

DTC P0100 MASS AIR FLOW SENSOR (MAFS)......187
Component Description ...........................................187
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................187
ECM Terminals and Reference Value .....................187
On Board Diagnosis Logic.......................................187
Fail-safe Mode .........................................................188
DTC Confirmation Procedure ..................................188
Wiring Diagram ........................................................189
Diagnostic Procedure ..............................................191
Component Inspection .............................................193
DTC P0110 INTAKE AIR TEMPERATURE
SENSOR......................................................................194
Component Description ...........................................194
On Board Diagnosis Logic.......................................195
DTC Confirmation Procedure ..................................195
Wiring Diagram ........................................................196
Diagnostic Procedure ..............................................198
Component Inspection .............................................200
DTC P0115 ENGINE COOLANT TEMPERATURE
SENSOR......................................................................201
Component Description ...........................................201
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................201
On Board Diagnosis Logic.......................................201
Fail-safe Mode .........................................................202
DTC Confirmation Procedure ..................................202
Wiring Diagram ........................................................203
Diagnostic Procedure ..............................................205
Component Inspection .............................................206
DTC P0120 THROTTLE POSITION SENSOR...........207
Component Description ...........................................207
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................207
ECM Terminals and Reference Value .....................208
On Board Diagnosis Logic.......................................208
Fail-safe Mode .........................................................208
DTC Confirmation Procedure ..................................208
Wiring Diagram ........................................................210
Diagnostic Procedure ..............................................212
Component Inspection .............................................214
DTC P0130 HEATED OXYGEN SENSOR 1
(FRONT) (CIRCUIT).....................................................216
Component Description ...........................................216
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................216
ECM Terminals and Reference Value .....................216
On Board Diagnosis Logic.......................................217
DTC Confirmation Procedure ..................................217
Overall Function Check ...........................................218
Wiring Diagram ........................................................219
Diagnostic Procedure ..............................................221Component Inspection .............................................222
DTC P0131 HEATED OXYGEN SENSOR 1
(FRONT) (LEAN SHIFT MONITORING).....................224
Component Description ...........................................224
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................224
ECM Terminals and Reference Value .....................224
On Board Diagnosis Logic.......................................225
DTC Confirmation Procedure ..................................225
Overall Function Check ...........................................226
Diagnostic Procedure ..............................................226
Component Inspection .............................................228
DTC P0132 HEATED OXYGEN SENSOR 1
(FRONT) (RICH SHIFT MONITORING)......................230
Component Description ...........................................230
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................230
ECM Terminals and Reference Value .....................230
On Board Diagnosis Logic.......................................231
DTC Confirmation Procedure ..................................231
Overall Function Check ...........................................232
Diagnostic Procedure ..............................................232
Component Inspection .............................................234
DTC P0133 HEATED OXYGEN SENSOR 1
(FRONT).......................................................................236
Component Description ...........................................236
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................236
ECM Terminals and Reference Value .....................236
On Board Diagnosis Logic.......................................237
DTC Confirmation Procedure ..................................237
Overall Function Check ...........................................238
Wiring Diagram ........................................................239
Diagnostic Procedure ..............................................241
Component Inspection .............................................243
DTC P0134 HEATED OXYGEN SENSOR 1
(FRONT) (HIGH VOLTAGE)........................................245
Component Description ...........................................245
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................245
ECM Terminals and Reference Value .....................245
On Board Diagnosis Logic.......................................246
DTC Confirmation Procedure ..................................246
Wiring Diagram ........................................................247
Diagnostic Procedure ..............................................249
Component Inspection .............................................250
DTC P0135 HEATED OXYGEN SENSOR 1
(FRONT) HEATER.......................................................252
Description ...............................................................252
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................252
ECM Terminals and Reference Value .....................252
CONTENTS(Cont'd)
EC-2

ECM Terminals and Reference Value .....................578
Wiring Diagram ........................................................579
Diagnostic Procedure - Load Signal - .....................583
Diagnostic Procedure - Heater Control Panel
(Fan Switch) - ..........................................................589
Component Inspection .............................................590
MI & DATA LINK CONNECTORS..............................591
Wiring Diagram ........................................................591
SERVICE DATA AND SPECIFICATIONS (SDS).......593
Fuel Pressure Regulator..........................................593
Idle Speed and Ignition Timing ................................593
Mass Air Flow Sensor..............................................593
Intake Air Temperature Sensor ................................593
Engine Coolant Temperature Sensor ......................593
Throttle Position Sensor ..........................................593
Heated Oxygen Sensor 1 Heater (Front) ................593
Heated Oxygen Sensor 2 Heater (Rear).................593
Fuel Tank Temperature Sensor (Where Fitted) .......594
EGR Volume Control Valve (Where Fitted) .............594
EGR Temperature Sensor (Where Fitted) ...............594
EVAP Canister Purge Volume Control Valve ..........594
IACV-AAC Valve ......................................................594
Injector .....................................................................594
Ignition Coil with Power Transistor ..........................594
Condenser ...............................................................594
Fuel Pump ...............................................................594
Crankshaft Position Sensor (POS) ..........................595
Camshaft Position Sensor (PHASE) .......................595
YD
TROUBLE DIAGNOSIS - INDEX................................596
Alphabetical & P No. Index for DTC .......................596
PRECAUTIONS...........................................................598
Supplemental Restraint System (SRS)²AIR
BAG²and²SEAT BELT PRE-TENSIONER²...........598
Engine Fuel & Emission Control System ................599
Precautions ..............................................................600
Wiring Diagrams and Trouble Diagnosis .................601
PREPARATION...........................................................602
Special Service Tools ..............................................602
ENGINE AND EMISSION CONTROL OVERALL
SYSTEM.......................................................................603
Engine Control Component Parts Location .............603
Circuit Diagram ........................................................606
System Diagram ......................................................608
System Chart ...........................................................609
ENGINE AND EMISSION BASIC CONTROL
SYSTEM DESCRIPTION.............................................610
Fuel Injection Control System .................................610
Fuel Injection Timing Control System...................... 611
Air Conditioning Cut Control ....................................612Fuel Cut Control (at no load & high engine
speed) ......................................................................612
Crankcase Ventilation System .................................613
BASIC SERVICE PROCEDURE.................................614
Injection Tube and Injection Nozzle ........................614
Electronic Control Fuel Injection Pump ...................618
Fuel Filter .................................................................625
ON BOARD DIAGNOSTIC SYSTEM
DESCRIPTION.............................................................627
DTC and MI Detection Logic ...................................627
Diagnostic Trouble Code (DTC) ..............................627
Malfunction Indicator (MI) ........................................628
CONSULT-II .............................................................632
TROUBLE DIAGNOSIS - INTRODUCTION................637
Introduction ..............................................................637
Work Flow ................................................................639
TROUBLE DIAGNOSIS - BASIC INSPECTION.........641
Basic Inspection.......................................................641
TROUBLE DIAGNOSIS - GENERAL
DESCRIPTION.............................................................646
Symptom Matrix Chart .............................................646
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................656
Major Sensor Reference Graph in Data Monitor
Mode ........................................................................658
ECM Terminals and Reference Value .....................659
TROUBLE DIAGNOSIS FOR INTERMITTENT
INCIDENT.....................................................................665
Description ...............................................................665
Diagnostic Procedure ..............................................665
TROUBLE DIAGNOSIS FOR POWER SUPPLY........666
Main Power Supply and Ground Circuit ..................666
DTC P0100 MASS AIR FLOW SEN...........................673
Component Description ...........................................673
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................673
ECM Terminals and Reference Value .....................673
On Board Diagnosis Logic.......................................673
DTC Confirmation Procedure ..................................673
Wiring Diagram ........................................................675
Diagnostic Procedure ..............................................677
DTC P0115 COOLANT TEMP SEN............................680
Description ...............................................................680
On Board Diagnosis Logic.......................................680
DTC Confirmation Procedure ..................................680
Wiring Diagram ........................................................682
Diagnostic Procedure ..............................................683
DTC P0120 ACCEL POS SENSOR............................685
Description ...............................................................685
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................685
ECM Terminals and Reference Value .....................685
CONTENTS(Cont'd)
EC-7

Diagnostic Procedure ..............................................790
DTC P1603 ECM 12, DTC P1607 ECM 2...................792
Description ...............................................................792
On Board Diagnosis Logic.......................................792
DTC Confirmation Procedure ..................................792
Diagnostic Procedure ..............................................793
DTC P1620 ECM RLY.................................................794
ECM Terminals and Reference Value .....................794
On Board Diagnosis Logic.......................................794
DTC Confirmation Procedure ..................................794
Wiring Diagram ........................................................795
Diagnostic Procedure ..............................................797
DTC P1621 ECM 15....................................................799
Description ...............................................................799
On Board Diagnosis Logic.......................................799
DTC Confirmation Procedure ..................................799
Diagnostic Procedure ..............................................800
DTC P1660 BATTERY VOLTAGE..............................801
On Board Diagnosis Logic.......................................801
DTC Confirmation Procedure ..................................801
Diagnostic Procedure ..............................................801
DTC P1690 P5.PUMP C/MODULE.............................803
Description ...............................................................803
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................803
ECM Terminals and Reference Value .....................804
On Board Diagnosis Logic.......................................804
DTC Confirmation Procedure ..................................804
Diagnostic Procedure ..............................................805
GLOW CONTROL SYSTEM.......................................806
Description ...............................................................806
ECM Terminals and Reference Value .....................807Wiring Diagram ........................................................808
Diagnostic Procedure ..............................................809
EGR VOLUME CONTROL SYSTEM..........................815
Description ...............................................................815
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................816
ECM Terminals and Reference Value .....................816
Wiring Diagram ........................................................817
Diagnostic Procedure ..............................................819
START SIGNAL...........................................................823
Wiring Diagram ........................................................823
Diagnostic Procedure ..............................................824
PARK/NEUTRAL POSITION (PNP) SWITCH
(WHERE FITTED)........................................................826
Description ...............................................................826
CONSULT-II Reference Value in Data Monitor
Mode ........................................................................826
ECM Terminals and Reference Value .....................826
Wiring Diagram ........................................................827
Diagnostic Procedure ..............................................828
AIR CONDITIONER CONTROL..................................830
Wiring Diagram ........................................................830
MI & DATA LINK CONNECTORS..............................831
Wiring Diagram ........................................................831
SERVICE DATA AND SPECIFICATIONS (SDS).......834
General Specifications .............................................834
Injection Nozzle .......................................................834
Engine Coolant Temperature Sensor ......................834
Crankshaft Position Sensor (TDC) ..........................834
Glow Plug ................................................................834
Accelerator Position Sensor ....................................834
EGR Volume Control Valve .....................................834
CONTENTS(Cont'd)
EC-9

Alphabetical & P No. Index for DTCNJEC0001Check if the vehicle is a model with the Euro-OBD (E-OBD) system or not by referring to the ªType approval
numberº on the identification plate.
Refer to GI-40, ªIDENTIFICATION PLATEº.
Type approval number Model
Available With Euro-OBD system
Not available Without Euro-OBD system
MODELS WITH EURO-OBD SYSTEMNJEC0001S03Alphabetical Index for DTCNJEC0001S0301
Items
(CONSULT-II screen terms)DTC*6
Reference page
CONSULT-II
GST*2ECM*1*7
Unable to access ECM Ð Ð EC-154
AIR TEMP SEN/CIRC P0110 0110 EC-194
A/T 1ST GR FNCTN P0731 0731 AT-204
A/T 2ND GR FNCTN P0732 0732 AT-211
A/T 3RD GR FNCTN P0733 0733 AT-217
A/T 4TH GR FNCTN P0734 0734 AT-223
A/T DIAG COMM LINE P1605 1605 EC-434
ATF TEMP SEN/CIRC P0710 0710 AT-189
CMP SEN/CIRCUIT P0340 0340 EC-335
CLOSED TP SW/CIRC*7 P0510 0510 EC-385
COOLANT T SEN/CIRC*3 P0115 0115 EC-201
CKP SEN/CIRCUIT P0335 0335 EC-328
CYL 1 MISFIRE P0301 0301 EC-318
CYL 2 MISFIRE P0302 0302 EC-318
CYL 3 MISFIRE P0303 0303 EC-318
CYL 4 MISFIRE P0304 0304 EC-318
ECM P0605 0605 EC-391
EGR SYSTEM*7 P0400 0400 EC-343
EGR SYSTEM*7 P1402 1402 EC-425
EGR TEMP SEN/CIRC*7 P1401 1401 EC-418
EGR VOL CON/V CIR*7 P0403 0403 EC-352
ENGINE SPEED SIG P0725 0725 AT-200
ENG OVER TEMP P1217 1217 EC-406
FUEL SYS-LEAN/BK1 P0171 0171 EC-297
FUEL SYS-RICH/BK1 P0172 0172 EC-305
FUEL TEMP SEN/CIRC*7 P0180 0180 EC-313
HO2S1 HTR (B1) P0135 0135 EC-252
HO2S1 (B1) P0130 0130 EC-216
TROUBLE DIAGNOSIS Ð INDEXQG
Alphabetical & P No. Index for DTC
EC-10

Items
(CONSULT-II screen terms)DTC*6
Reference page
CONSULT-II
GST*2ECM*1*7
HO2S1 (B1) P0131 0131 EC-224
HO2S1 (B1) P0132 0132 EC-230
HO2S1 (B1) P0133 0133 EC-236
HO2S1 (B1) P0134 0134 EC-245
HO2S2 (B1) P0137 0137 EC-258
HO2S2 (B1) P0138 0138 EC-267
HO2S2 (B1) P0139 0139 EC-275
HO2S2 (B1) P0140 0140 EC-284
HO2S2 HTR (B1) P0141 0141 EC-291
IACV/AAC VLV/CIRC P0505 0505 EC-376
INT/V TIM V/CIR-B1 P1111 1111EC-393
KNOCK SEN/CIRC-B1 P0325 0325 EC-324
L/PRESS SOL/CIRC P0745 0745 AT-239
MAF SEN/CIRCUIT*3 P0100 0100 EC-187
MULTI CYL MISFIRE P0300 0300 EC-318
NATS MALFUNCTION P1610 - P1615 1610 - 1615 EL-430
NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIREDÐ 0000 Ð
NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIREDÐ Flashing*5 EC-75
O/R CLTCH SOL/CIRC P1760 1760 AT-268
PNP SW/CIRC P0705 0705 AT-183
P-N POS SW/CIRCUIT P1706 1706 EC-437
PURG VOLUME CONT/V P0443 0443 EC-364
SFT SOL A/CIRC P0750 0750 AT-246
SFT SOL B/CIRC P0755 0755 AT-252
SWRL CONT SOL/V*7 P1131 1131 EC-399
TCC SOLENOID/CIRC P0740 0740 AT-233
THRTL POS SEN/CIRC*3 P0120 0120 EC-207
TP SEN/CIRC A/T P1705 1705 AT-258
TW CATALYST SYS-B1 P0420 0420 EC-359
VEH SPD SEN/CIR AT P0720 0720 AT-195
VEH SPEED SEN/CIRC*4 P0500 0500 EC-370
*1: In Diagnostic Test Mode II (Self-diagnostic results). These numbers are controlled by NISSAN.
*2: These numbers are prescribed by ISO 15031-6.
*3: When the fail-safe operation occurs, the MI illuminates.
*4: The MI illuminates when the ªRevolution sensor signalº and the ªVehicle speed sensor signalº meet the fail-safe condition at the
same time.
*5: While engine is running.
*6: 1st trip DTC No. is the same as DTC No.
TROUBLE DIAGNOSIS Ð INDEXQG
Alphabetical & P No. Index for DTC (Cont'd)
EC-11

DTC*6
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*2ECM*1*7
P0500 0500 VEH SPEED SEN/CIRC*4 EC-370
P0505 0505 IACV/AAC VLV/CIRC EC-376
P0510 0510 CLOSED TP SW/CIRC*7 EC-385
P0605 0605 ECM EC-391
P0705 0705 PNP SW/CIRC AT-183
P0710 0710 ATF TEMP SEN/CIRC AT-189
P0720 0720 VEH SPD SEN/CIR AT AT-195
P0725 0725 ENGINE SPEED SIG AT-200
P0731 0731 A/T 1ST GR FNCTN AT-204
P0732 0732 A/T 2ND GR FNCTN AT-211
P0733 0733 A/T 3RD GR FNCTN AT-217
P0734 0734 A/T 4TH GR FNCTN AT-223
P0740 0740 TCC SOLENOID/CIRC AT-233
P0745 0745 L/PRESS SOL/CIRC AT-239
P0750 0750 SFT SOL A/CIRC AT-246
P0755 0755 SFT SOL B/CIRC AT-252
P 1111 1111INT/V TIM V/CIR-B1 EC-393
P1131 1131 SWRL CONT SOL/V*7 EC-399
P1217 1217 ENG OVER TEMP EC-406
P1401 1401 EGR TEMP SEN/CIRC*7 EC-418
P1402 1402 EGR SYSTEM*7 EC-425
P1605 1605 A/T DIAG COMM LINE EC-434
P1610 - 1615 1610 - 1615 NATS MALFUNCTION EL-430
P1705 1705 TP SEN/CIRC A/T AT-258
P1706 1706 P-N POS SW/CIRCUIT EC-437
P1760 1760 O/R CLTCH SOL/CIRC AT-268
*1: In Diagnostic Test Mode II (Self-diagnostic results). These numbers are controlled by NISSAN.
*2: These numbers are prescribed by ISO 15031-6
*3: When the fail-safe operation occurs, the MI illuminates.
*4: The MI illuminates when the ªRevolution sensor signalº and the ªVehicle speed sensor signalº meet the fail-safe condition at the
same time.
*5: While engine is running.
*6: 1st trip DTC No. is the same as DTC No.
*7: If so equipped
TROUBLE DIAGNOSIS Ð INDEXQG
Alphabetical & P No. Index for DTC (Cont'd)
EC-13

MODELS WITHOUT EURO-OBD SYSTEMNJEC0001S04Alphabetical Index for DTCNJEC0001S0401
Items
(CONSULT-II screen terms)DTC*6
Reference page
CONSULT-II
GST*2ECM*1
Unable to access ECM Ð Ð EC-154
CKP SEN/CIRCUIT P0335 0335 EC-328
CMP SEN/CIRCUIT P0340 0340 EC-335
COOLANT T SEN/CIRC*3 P0115 0115 EC-201
ENG OVER TEMP P1217 1217 EC-406
HO2S1 (B1) P0130 0130 EC-216
KNOCK SEN/CIRC-B1 P0325 0325 EC-324
MAF SEN/CIRCUIT*3 P0100 0100 EC-187
NATS MALFUNCTION P1610 - P1615 1610 - 1615 EL-430
NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIREDÐ 0000 Ð
NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIREDÐ Flashing*5 EC-75
THRTL POS SEN/CIRC*3 P0120 0120 EC-207
VEH SPEED SEN/CIRC*4 P0500 0500 EC-370
*1: In Diagnostic Test Mode II (Self-diagnostic results) (If so equipped). These numbers are controlled by NISSAN.
*2: These numbers are prescribed by ISO 15031-6.
*3: When the fail-safe operation occurs, the MI illuminates.
*4: The MI illuminates when the ªRevolution sensor signalº and the ªVehicle speed sensor signalº meet the fail-safe condition at the
same time.
*5: While engine is running.
*6: 1st trip DTC No. is the same as DTC No.
P No. Index for DTCNJEC0001S0402
DTC*6
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*2ECM*1
Ð Ð Unable to access ECM EC-154
Ð Flashing*5NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIRED.EC-75
Ð 0000NO DTC IS DETECTED.
FURTHER TESTING MAYBE REQUIRED.Ð
P0100 0100 MAF SEN/CIRCUIT*3 EC-187
P0115 0115 COOLANT T SEN/CIRC*3 EC-201
P0120 0120 THRTL POS SEN/CIRC*3 EC-207
P0130 0130 HO2S1 (B1) EC-216
P0325 0325 KNOCK SEN/CIRC-B1 EC-324
P0335 0335 CKP SEN/CIRCUIT EC-328
P0340 0340 CMP SEN/CIRCUIT EC-335
P0500 0500 VEH SPEED SEN/CIRC*4 EC-370
TROUBLE DIAGNOSIS Ð INDEXQG
Alphabetical & P No. Index for DTC (Cont'd)
EC-14