turn signal NISSAN ALTIMA COUPE 2009 D32 / 4.G Quick Reference Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2009, Model line: ALTIMA COUPE, Model: NISSAN ALTIMA COUPE 2009 D32 / 4.GPages: 36, PDF Size: 5.3 MB
Page 6 of 36
HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM (if so
equipped):
Turn the headlight control switchto theAUTO position
to activate the autolight system. The autolight system can:
Turn the headlights on automatically when it is dark.
Turn the headlights off automatically when it is light.
Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and all
doors are closed.
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
Turn the headlight control switchto the OFF,orposition.
HEADLIGHT CONTROL SWITCH
Turn the headlight control switchto theposition to turn on the front parking,
tail, license plate and instrument panel lights.
Turn the headlight control switch
to theposition to turn on the headlights. All
other lights remain on.
FOG LIGHT OPERATION (if so equipped)
NOTE: Theheadlights mustbeonand thelow beamsselected forthe fog lights to
operate.
Turn the switch (inside collar)
to theposition to turn on the fog lights.
Turn the switch (inside collar)
to the OFFposition to turn off the fog lights.
HIGH BEAM
Push theheadlight controlswitchforwardto
select the high beam function. The blue
indica-
tor light illuminates. Pull the headlight switch back to
the original position toselect thelow beam. The
blue
indicator light goes off.
Pull and release the headlight control switch
to flash the headlight high beams on
and off.
4
Page 19 of 36
3.Using both hands, simultaneously press and hold both the HomeLink button you want
to program and the hand-held transmitter button. DO NOT release the buttons until
step 4 has been completed.
4. Hold down bothbuttons untiltheindicator lightonthe HomeLink flashes, changing
from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When
the indicator lightflashes rapidly, bothbuttons maybereleased. Therapidly flashing
light indicates successful programming. Toactivate thegarage doororother pro-
grammed device, press and hold the programmed HomeLink button - releasing when
the device begins to activate.
5. Ifthe indicator lightonthe HomeLink blinksrapidly fortwo seconds andthen turns
solid, HomeLink haspicked upa“rolling code” garage dooropener signal.Youwill
need to proceed with the next steps to train the HomeLink to complete the program-
ming, which may require a ladder and another person for convenience.
6. Press andrelease the“smart” or “learn” program buttonlocated onthe garage door
opener’s motor to activate the “training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire originates from under a light
lens, you will need to remove the lens to access the program button.
NOTE: Onceyouhave pressed andreleased theprogram buttononthe garage
door opener’s motor and the “training light” is lit, you have 30 seconds in which
to perform step 7. Use the help of a second person for convenience to assist when
performing this step.
7. Quickly within 30 seconds of pressing and releasing the garage door opener program
button, firmly press and release the HomeLink button you’ve just programmed. Press
and release the HomeLink button up to three times to complete the training.
8. Your HomeLink buttonshould now
beprogrammed. (T
oprogram theremaining
HomeLink buttons for additional door or gate openers, follow steps 2-8 only.)
BLUETOOTH HANDS-FREE PHONE SYSTEM (Without Navigation
System – if so equipped)
With anoverhead microphone andsound
transmitted throughtheaudio system
speaker, theBluetooth Hands-Free Phone
System utilizesBluetooth wirelesstechnol-
ogy and voice recognition toprovide hands-
free cellular phone communication.
SYSTEM OPERATING TIPS
Close allwindows. Surrounding noises
may interfere with system operation and
performance.
Press the
button on the steering wheel to activate voice recognition.
Wait for the tone before speaking.
Begin speaking a command within 5 seconds of the tone.
To go back to the previous command, say “Go back” or “Correction”.
To cancel a voice recognition session, simply wait 5 seconds, say “Cancel” or “Quit”, or
press the
button.17