lock NISSAN ALTIMA COUPE 2011 D32 / 4.G Warranty Booklet

Nissan makes available to you, and you are specifi-
cally required by Federal Law to use BBB AUTO
LINE [(800) 955-5100] before exercising rights or
seeking remedies under the Federal Magnuson-
Moss Warranty Act, 15 U.S.C. §2301, et. seq. You
are not required to first use BBB AUTO LINE if you
seek remedies not created by Title I of that Federal
law, except that you are required to first use BBB
AUTO LINE in good faith if you seek remedies cre-
ated by state law, including your state’s lemon law,
if applicable state law provides for using a 703
compliant or similar process before filing suit.
Please refer to pp. 2-3 of this booklet and the
Supplement to 2011 Nissan Warranty Information
Booklet & 2011 Nissan Owner’s Manualfor addi-
tional information.
THE WARRANTY BEGINS
The warranty period begins on the date the vehicle is
delivered to the first retail buyer or put into use, which-
ever is earlier.
FOR HOW LONG AND WHAT IS
COVERED
BASIC COVERAGE
The basic coverage period is 36 months or
36,000 miles, whichever comes first.
This warranty covers any repairs needed to
correct defects in materials or workmanship of
all parts and components of each new Nissan
vehicle supplied by Nissan except for the exclu-
sions or items listed under the caption “WHAT
IS NOT COVERED” or, if the part is covered by
one of the separate coverages described in the
following sections of this warranty, that specific
coverage applies instead of the basic cover-
age.
Bedliners will be repaired to commercially ac-
ceptable standards subject to the conditions
and limitations listed in WHAT IS NOT COV-
ERED.
POWERTRAIN COVERAGE
The Powertrain coverage period is 60 months
or 60,000 miles, whichever comes first.
This warranty covers any repairs needed to
correct defects in materials or workmanship.
Powertrain coverage applies to components
listed below, supplied by Nissan except for
those items listed under the caption “WHAT IS
NOT COVERED”.
ENGINE
Cylinder heads and block and all internal parts,
rocker covers and oil pan, valve train and front
cover, timing chain and tensioner, oil pump, water
pump and fuel pump, fuel injectors, intake and
exhaust manifolds and supercharger, flywheel,
seals, and gaskets. TRANSMISSION AND TRANSAXLE
Case and all internal parts, torque converter and
converter housing, automatic transmission control
module, transfer case and all internal parts, seals
and gaskets, clutch cover and housing, and elec-
tronic transmission controls.
DRIVETRAIN
Drive shafts, final drive housing and all internal
parts, propeller shafts, universal joints, bearings,
seals and gaskets.
RESTRAINT SYSTEM
Air bags and related electronic control systems.
CORROSION COVERAGE (PERFORATION
FROM CORROSION)
Any body sheet metal panel supplied by Nissan
found to have developed perforation (rust-
through) due to corrosion in normal use is covered
for 60 months, regardless of mileage, except for
those items listed under “WHAT IS NOT COV-
ERED”. No additional rust proofing applications
are required. Perforation is a condition in which
any body sheet metal panel has corroded from one
surface through to another.
TOWING COVERAGEIf your vehicle is inoperative due to the failure of a
warranted part, towing service to the nearest au-
thorized Nissan dealer is covered for 36 months or
36,000 miles, whichever comes first.
(Continued on next page)
6 2011 NEW VEHICLE LIMITED WARRANTY

WHO IS COVERED
The owner of a BFGoodrich Passenger or Light Truck
tire which bears the BFGoodrich name and complete
DOT identification number.
WHAT IS COVERED AND FOR HOW LONG
BFGoodrich Passenger and Light Truck tires, used in
normal service on the vehicle on which they were origi-
nally fitted and in accordance with the maintenance
recommendations and safety warnings contained in the
owner’s manual and in the Important Tire Safety Infor-
mation Section of this booklet, are covered by this
limited warranty against defects in workmanship and
material for the life of the original usable tread, or 6 years
from the date of purchase, whichever comes first. At
that time, all warranties, express or implied, are termi-
nated. The usable tread is the original tread down to the
level of the tread wear indicators - 2/32nds of an inch
(1.6mm) of tread remaining. Date of purchase is docu-
mented by new vehicle registration or tire sales invoice.
If no proof of purchase is available, the date of manu-
facture, as molded on the sidewall, will be used. Re-
placement will be made in accordance with the terms
and conditions described underWhat BFGoodrich
Will Do.
WHAT IS NOT COVERED
Tires which become unserviceable due to:Road hazard injury (e.g., a cut, snag, bruise, impact
damage, or puncture, whether repairable or not);
Incorrect mounting of the tire, tire/wheel imbalance,
or improper repair;
Misapplication, underinflation, overinflation, im-
proper maintenance, racing or other abuse;
Uneven or rapid wear which is caused by mechani-
cal irregularity in the vehicle such as wheel misalign-
ment (a measured tread difference of 2/32nds of an
inch (1.6mm) or more across the tread on the same
tire) resulting in uneven or rapid wear;
Accident, fire, chemical corrosion, tire alteration, or
vandalism;
Ozone or weather cracking;Flat spotting caused by improper storage or brake-
lock;
The adding of liquid, solid or gaseous materials other
than air, nitrogen, or carbon dioxide (e.g. waterbase
sealers or balancing substances) .
WHAT BFGOODRICH WILL DO
PASSENGER AND LIGHT TRUCK TIRES
A tire which becomes unserviceable due to a condition
covered by this limited warranty will be replaced with a
comparable new BFGoodrich tire, free of charge, when
2/32nds of an inch (1.6mm) or less of the original tread
is worn, (or 25% or less, whichever is most beneficial to
the user) and within 12 months of the date of purchase.
Mounting and balancing of tires is included. The cost of
any other service charges and applicable taxes are
payable by the user.
When more than 2/32nds of an inch of original tread
has been worn (or more than 25%, whichever is most
beneficial to the user) or after 12 months from date of
purchase, the user must pay the cost of a comparable
new BFGoodrich passenger or light truck replacement
tire on a pro rata basis. The dealer shall determine the
charge by multiplying the percentage of the original
usable tread worn by the current actual selling price at
the adjustment location or the price on the current
BFGoodrich Brand Base Price List, whichever is lower.
This List is based on a predetermined price intended to
fairly represent the actual selling price of the tire. The
cost of mounting, balancing and any other service
charges and applicable taxes are payable by the user.
(Continued on next page)
18 BFGOODRICH TIRE LIMITED WARRANTY

DON’T ATTEMPT TO MOUNT YOUR
OWN TIRES
Serious injury or Death may result from explosion of tire/
rim assembly due to improper mounting procedures.
Follow tire manufacturer’s instructions and match tire
diameter to rim diameter. Mount light truck radials on
rims approved for radial service. Do not apply bead
sealer. This can inhibit bead seating. Lubricate beads
and tire rim (including tube or flap) contact surfaces.
Lock assembly on mounting machine or place in safety
cage. STAND BACK and never exceed 40 psi to seat
beads. Never use a volatile substance or a rubber
“donut” (also known as a bead expander or “O-Ring”) to
aid bead seating. Only specially-trained persons should
mount tires.
DON’T MIX TIRES OF DIFFERENT
SIZES AND TYPES ON THE SAME
AXLE
For optimum handling and control, Goodyear and Dun-
lop recommend fitment of four (4) tires of the same type
and size unless otherwise specified by the vehicle
manufacturer.
WARNING: Before you replace your tires, always con-
sult the vehicle owner’s manual and follow the vehicle
manufacturer’s replacement tire recommendations. Ve-
hicle handling may be significantly affected by a change
in tire size or type. When selecting tires that are different
than the Original Equipment size, see a professional
installer in order to make certain that proper clearance,
load carrying capacity and inflation pressure is selected.
Never exceed the maximum load capacity and inflationpressure listed on the sidewall of the tire. Always drive
safely and obey all traffic laws. Avoid sudden, sharp
turns or lane changes. Failure to follow this warning may
result in loss of control of the vehicle, leading to an
accident and serious injury or death.
When replacing tires, you must maintain the outside
diameter and load carrying capacity of the Original
Equipment tire. Inflation pressure may need to be ad-
justed to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or
JATMA standards for correct load and inflation informa-
tion.
NEVER FIT TIRES TO A VEHICLE THAT
HAVE LESS LOAD CARRYING
CAPACITY THAN AS REQUIRED BY
THE ORIGINAL EQUIPMENT
MANUFACTURER
Examples: Many vehicles, such as large passenger
vans, require Load Range E tires as designated by the
vehicle manufacturer. Fitment of a tire, such as a Load
Range D, with less carrying capacity is not allowed.
In other cases, tires of the same size may carry different
load indexes in the service description. You must make
certain the replacement tires fitted to the vehicle have a
load carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.
FOLLOW THESE ADDITIONAL
GUIDELINES
Fit newest tires on rear axle. If radials and non-radials
must be fitted to the same vehicle, fit radials on rear axle.Never mix radials and non-radials on the same axle.
When fitting snow tires or all-season tires to perfor-
mance vehicles, always fit in sets of four. It is not
recommended to fit tires with different speed ratings. If
tires with different speed ratings are installed on a
vehicle, they should be installed with like pairs on the
same axle. The speed capability of the vehicle will
become limited to that of the lowest speed rated tires. It
is also recommended that the lower speed rated tires
be placed on the front axle regardless of which axle is
driven to help prevent potential oversteer.
Use of lift kits with some vehicle/tire combinations can
cause instability. When changing tire sizes, always con-
sult Dealer for optimum rim width and carefully checkvehicle/tire clearances.
RETREADED TIRES
Retreaded passenger and light truck tires are not war-
ranted by Goodyear and Dunlop for any reason. Good-
year and Dunlop speed ratings and U.S. Department of
Transportation test compliance certifications are voided
for retreaded tires.
DO MAINTAIN VEHICLE SUSPENSION,
WHEEL ALIGNMENT AND BALANCE
AND ROTATE YOUR TIRES
Lack of rotation, worn suspension parts, underinflation/
overinflation, wheel imbalance and misalignment can
cause vibration or irregular tire wear. Rotate your tires
according to your vehicle manufacturer’s recommenda-
tions or at maximum intervals of 6,000 miles/10,000 km.
(Continued on next page)
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
27

WHO IS COVERED
The owner of a Michelin Passenger or Light Truck tire
which bears the Michelin name and complete DOT
identification number.
WHAT IS COVERED AND FOR HOW LONG
Michelin Passenger and Light Truck tires, used in nor-
mal service on the vehicle on which they were originally
fitted and in accordance with the maintenance recom-
mendations and safety warnings contained in the own-
er’s manual and in the Important Tire Safety Information
Section of this booklet, are covered by this limited
warranty against defects in workmanship and material
for the life of the original usable tread, or 6 years from
the date of purchase, whichever comes first. At that
time, all warranties, express or implied, are terminated.
The usable tread is the original tread down to the level of
the tread wear indicators - 2/32nds of an inch (1.6mm)
of tread remaining. Date of purchase is documented by
new vehicle registration or tire sales invoice. If no proof
of purchase, coverage will be based on date of manu-
facture. Replacement will be made in accordance with
the terms and conditions described underWhat Mich-
elin Will Do.
WHAT IS NOT COVERED
Tires which become unserviceable due to:Road hazard injury (e.g., a cut, snag, bruise, impact
damage, or puncture, whether repairable or not);
Incorrect mounting of the tire, tire/wheel imbalance,
or improper repair;
Misapplication, underinflation, overinflation, im-
proper maintenance, racing, or other abuse;
Uneven or rapid wear which is caused by mechani-
cal irregularity in the vehicle such as wheel misalign-
ment (a measured tread difference of 2/32nds of an
inch (1.6mm) or more across the tread on the same
tire) resulting in uneven or rapid wear;
Accident, fire, chemical corrosion, tire alteration, or
vandalism;
Ozone or weather cracking;Flat spotting caused by improper storage or brake-
lock;
The adding of liquid, solid or gaseous materials other
than air, nitrogen, or carbon dioxide (e.g. waterbase
sealers or balancing substances) .
WHAT MICHELIN WILL DO
PASSENGER AND LIGHT TRUCK TIRES
A tire which becomes unserviceable due to a condition
covered by this limited warranty will be replaced with a
comparable new Michelin tire, free of charge, when
2/32nds of an inch (1.6mm) or less of the original tread
is worn, (or 25% or less, whichever is most beneficial to
the user) and within 12 months of the date of purchase.
Mounting and balancing of tires is included. The cost of
any other service charges or applicable taxes are pay-
able by the user. When more than 2/32nds of an inch of original tread
has been worn (or more than 25%, whichever is most
beneficial to the user) or after 12 months from date of
purchase, the user must pay the cost of a comparable
new Michelin passenger or light truck replacement tire
on a pro-rata basis. The dealer shall determine the
charge by multiplying the percentage of the original
usable tread worn by the current actual selling price at
the adjustment location or the price on the current
Michelin Base Price List, whichever is lower. This List is
based on a predetermined price intended to fairly rep-
resent the actual selling price of the tire. The cost of
mounting, balancing and any other service charges or
applicable taxes are payable by the user.
WHAT THE CONSUMER MUST DO
When making a claim under the terms of this limited
warranty, the consumer must present the tire to an
authorized Michelin Dealer. To locate an Authorized Tire
Dealer, check the yellow pages under “Tire Dealers -
Retail.”
The vehicle on which the tire was used should be
available for inspection.
It is essential that you read and understand the safety
and maintenance recommendations (see Safety Main-
tenance Information) for your tires.
(Continued on next page)
32
MICHELIN TIRE LIMITED WARRANTY

TREAD WEAR INDICATORS (WEAR BARS):Tires
contain Tread Wear Indicators (Wear Bars) in the
grooves of the tire tread which show up when only
2/32nds of an inch (1.6mm) of tread is remaining.
At this stage, your tires must be replaced. Tires
worn beyond this stage are dangerous.
* Provided by and published at the request of the tire
manufacturers/warrantors.
HAZARDS
Objects in the road that threaten a tire should be safely
avoided. These objects are potholes, glass, metal,
rocks, wood debris and the like. Unavoidable contact
should prompt a thorough tire inspection.
You may not always recall hitting an object that can
damage or injure your tires. If while driving your vehicle
experiences any unusual vibrations, ride disturbance or
noise and/or you suspect that possible damage to the
tires or vehicle has occurred, DO NOT JAM OR LOCK
YOUR BRAKES! Rather reduce your speed and drive
with caution until you can safely pull off the road. Stop
and inspect the tires. If the tire is underinflated or
damaged, deflate, remove the tire and rim assembly and
replace it with your spare. If you cannot detect a cause,
have the vehicle towed to the nearest vehicle or tire
dealer to have the vehicle inspected.
REPAIRING, MOUNTING AND
DEMOUNTING OF TIRES
Do not attempt to repair, mount or demount a tire
yourself. Tire changing can be dangerous and must be
done by professionally trained persons using proper
tools and procedures as specified by the Rubber Manu-
facturers Association (RMA) . Follow these mounting
recommendations. Your tires should be mounted on
wheels of correct size and type and which are in good,
clean condition. Bent, chipped or rusted wheels may
cause tire damage. The inside of the tire must be free
from foreign materials. Have your dealer check the
wheels before mounting new tires. Mismatched tires
and rims can explode during mounting. Also, mis-
matched tires and rims can result in dangerous tire
failure on the road. If a tire is mounted by error on the
wrong-sized rim, do not remount it on the proper rim -
scrap it. It may be damaged internally (which is not
externally visible) by being dangerously stretched and
could fail on the highway.
Old valves may leak. When new tubeless tires are
mounted, have new valves of the correct type installed.
Tubeless tires must be mounted only on wheels de-
signed for tubeless tires, i.e., wheels which have safety
humps or ledges.
Never perform a temporary repair, use an innertube or
inject sealant as a permanent substitute for a proper
repair. Only qualified persons should repair tires.
Be sure that all your valves have suitable valve caps.
This will keep valve cores clean and clear and guard
against leakage. REPAIRS - WHENEVER POSSIBLE, SEE A TIRE
DEALER AT ONCE.
Some tire manufacturers do not
warrant any inspection or repair process. The repair is
entirely the responsibility of the repairer. Punctures in
the tread of a passenger tire which do not exceed 1/4 of
an inch (6mm) in diameter can usually be repaired by
following the Rubber Manufacturer’s Association
(RMA) Passenger and Light Truck Repair procedures.
Contact the manufacturer of your tires for its position
and assistance as to the acceptable location for a
proper repair and the repair of speed rated tires. Do not
use plug repairs. They may cause further damage
to the tire. They are not always air tight and the
plug may fail. Do not exceed posted speed limits on
any repaired tire. Certain tire manufacturers speed rat-
ings are voided if the tire is repaired.
Although a tire was properly repaired, internal structural
damage resulting from the puncture may have occurred.
Sometime later the damage may cause the tire to be
removed from service.
If the tire has a puncture in the tread which exceeds 1/4
inch (6mm) , the tire must be replaced. If any tire has
sustained a puncture, have the tire inspected internally
by a tire dealer for possible damage that may have
occurred.
Improper mounting and inflation procedures can cause
an explosion of the tire/rim assembly. Only specially
trained persons should perform these tasks. Contact
your tire store or dealer for assistance.
CAUTION - Never, under any circumstance, in-
troduce a flammable substance into a tire.
(Continued on next page)
42 IMPORTANT TIRE SAFETY INFORMATION*