steering wheel NISSAN ALTIMA HYBRID 2010 L32A / 4.G First Responders Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2010, Model line: ALTIMA HYBRID, Model: NISSAN ALTIMA HYBRID 2010 L32A / 4.GPages: 27, PDF Size: 4.43 MB
Page 8 of 27
Hybrid System Locations and Descriptions
Component
Location Description
1. Electric Air
Conditioning
Compressor
Engine compartment, front
passenger side
Electric motor driven compressor supplied with 245 volts
DC.
2. Electric Power
Steering Engine compartment, on
steering rack A 42 volt DC assist motor is used for the electric power
steering (EPS) system.
3. EPS DC/DC
Converter Trunk area, mounted to top
of high voltage battery Converts 245 volts DC (high voltage) to 42 volts DC (low
voltage) for the EPS.
4. High Voltage
Battery Trunk area, mounted to
cross member and behind
rear seat 245 volt DC Nickel Metal Hydride (Ni-MH) battery
consisting of 34 low voltage (7.2 volt) modules connected
in series.
5. DC/DC
Converter
Trunk area, under front left
cover of the high voltage
battery Converts 245 volts DC (high voltage) to 12 volts DC (low
voltage) for charging the 12 volt battery.
6. Service
Disconnect
Trunk area, on the
passenger side of the high
voltage battery Used to disable the high voltage system.
7. High Voltage
Harnesses
•
Trunk area, on high
voltage battery and
EPS DC/DC converter
• Under passenger side
rear seat and floor pan
• Engine compartment,
on rear, driver side and
front Orange colored power cables carry high voltage direct
current (DC) between the high voltage battery, EPS
DC/DC converter, inverter unit, and electric air
conditioning compressor. There are two cables which also
carry 3-phase alternating current (AC) between the
inverter unit and transaxle.
NOTE:
High voltage cables under the vehicle floor are encased in
a black plastic protector.
8. Transaxle
Engine compartment, on
driver side Contains a traction motor and generator used to drive the
front wheels and recharge the high voltage battery.
9. Inverter Unit
Engine compartment, front
driver side Changes the 245 volts DC from the high voltage battery to
3-phase 650 volts AC to power the transaxle. The inverter
unit also changes AC electricity from the transaxle to DC
that recharges the high voltage battery.
- 8 -
Page 21 of 27
• Repositioning the steering wheel:
The Altima Hybrid is equipped with a tilting telescopic
steering column. To adjust the tilt: pull the lever (1) all the
way toward you and adjust the steering wheel up or down
in the desired direction (2). Release the lever after the
desired position has been achieved.
To adjust the telescopic position: pull the lever (1) all the
way toward you and adjust the steering wheel forward or
backward (3) into the desired position. Release the lever
after the desired position has been achieved.
Fire
Approach and extinguish a fire using proper vehicle fire fighting practices as recommended by NFPA, IFSTA,
or the National Fire Academy (USA).
• Extinguishing agent
Water has been proven to be a suitable extinguishing agent.
• Initial fire attack
Perform a fast, aggressive fire attack.
Divert the runoff from entering watershed areas.
Attack teams may not be able to identify an Altima Hybrid until the fire has been knocked down
and overhaul operations have commenced.
• Fire in a high voltage battery
Should a fire occur in the Ni-MH high voltage battery, attack crews should utilize a water stream
or fog pattern to extinguish any fire within the trunk EXCEPT for the high voltage battery.
DANGER:
•
Never breach or remove the high voltage battery under any circumstances, including fire. Doing
so could result in serious injury or death from electrical shock.
• The Ni-MH battery electrolyte is a caustic alkaline (pH 13.5) that is damaging to human tissues. To
avoid injury by coming in contact with the electrolyte, wear proper personal protective equipment.
When allowed to burn themselves out, the Altima Hybrid Ni-MH battery modules burn rapidly and can quickly
be reduced to ashes except for the metal.
Offensive fire attack
Flooding the Altima Hybrid high voltage battery is not
recommended due to the battery case design and
location preventing the responder from properly, and safely, applying water through the available vent
openings. Therefore, it is recommended that the incident commander allow the Altima Hybrid high voltage
battery to burn itself out.
Normally
, flooding a Ni-MH high voltage battery with copious amounts of water at a safe distance will
effectively control the high voltage battery fire by cooling the adjacent Ni-MH battery modules to a point below
their ignition temperature. The remaining modules on fire, if not extinguished by the water, will burn themselves
out.
Defensive fire attack
If the decision has been made to fight the fire using a def ensive attack, the fire attack crew should pull back a
safe distance and allow the Ni-MH battery modules to burn themselves out. During this defensive operation,
fire crews may utilize a water stream or fog pattern to protect exposures or to control the path of smoke.
- 21 -