NISSAN FRONTIER 2006 D22 / 1.G Quick Reference Guide

MANUAL CLIMATE CONTROL11
FAN SPEED CONTROL DIAL Turn the fan speed control dial to the left (slow) or right (fast) to control fan speed.
TEMPERATURE CONTROL DIAL Turn the temperature control dial for the desired temperature. Turn the control dial
to the left for cold air or right for hot air.
AIR FLOW CONTROL DIAL Turn the dial to select the following air flow outlets:
Air flows from center and side vents with maximum cooling (air conditioning).
Air flows from center and side vents.
Air flows from center and side vents and the front and rear floor outlets.
Air flows mainly from the front and rear floor outlets.
Air flows from defroster outlets and the front and rear floor outlets.
Air flows mainly from defroster outlets.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
 Turn the air flow control dial to the front window defroster mode . The A/C automatically turns on when the defroster mode is selected.
 Turn the temperature control dial left or right to set the desired temperature.
 To set the defroster on high, turn the fan speed dial all the way to the right.
DEFROSTING/DEFOGGING REAR WINDOW AND OUTSIDE HEATED MIRROR (if so equipped)
Push the rear window defroster switch on. Push the switch again to manually turn the defroster off. Note: The rear window defroster automatically turns off in approximately 15 minutes.
A/C ON/OFF BUTTON (if so equipped) Press the A/C button to turn the A/C on or off.
AIR R ECIRCULATION BUTTON (if so equipped)
 Press the air recirculation button to recirculate air inside the vehicle.
 Press the air recirculation button again to turn air recirculation off.
 The air recirculation mode cannot be selected if the air flow control dial is in the defrost position .
PRESET A.B.C BUTTON Press the PRESET A · B · C button until you reach the desired setting. The radio is equipped with three separate banks, each with six station presets. You may store any combination of AM, FM or SAT* radio presets on each bank.
CD BUTTON When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play.
BAND SELECT BUTTON Press the BAND button to change from AM to FM reception.
CD EJECT BUTTON When the CD eject button is pressed with a compact disc loaded, the compact disc ejects. When the button is pressed while the compact disc is playing, the compact disc ejects and the system turns off.
SEEK/TRACK BUTTON To scan quickly through each broadcasting station, press and hold the SEEK/TRACK button for more than 1.5 seconds to enter scan mode. The tuner will pause for 5 seconds on each broadcasting station. To skip from one track to another on a CD, press the SEEK/TRACK button. Each time the button is pressed, the CD will advance or skip back one track.
STATION AND CD SELECT BUTTONSTo store a radio station in a preset you must first select A, B, or C memory bank by pressing the PRESET A.B.C button and tune to the desired AM, FM or SAT* station. Then, press and hold the desired station select button for at least 2 seconds. When the preset indicator illuminates, a beep will sound, indicating memorization is complete. To retrieve a previously set station, select the memory bank where the preset was set, then press the corresponding station select button.
MENU BUTTON When the MENU button is pressed while the compact disc is playing, the play pattern changes as follows:
 RPT – The current selection is repeated.
 MIX – Tracks are played at random, not following the sequence on the compact
disc. The same track may be repeated twice. If the button is pressed in the MIX
mode, tracks will be chosen at random.
AUDIO BUTTON To adjust the audio levels for bass, treble, fader, and balance, press the AUDIO button and adjust the level with the SEEK/TRACK button.
AM/FM/SAT* RADIO WITH CD PLAYER (if so equipped)12
* SAT presets are only available on SAT equipped vehicles.
05
04
06
03
02
01
05
04
08
07
06
03
02
01
UTILITY BED WITH SPRAY-ON BED LINER
AND UTILI-TRACK ™ SYSTEM
(if so equipped)
The Utili-track™ channel system allows you to move tie-down clamps in the bed to the best location to
secure a load.
 The tie-down cleats must be installed so the clamp is properly seated in the notches in the rail. If the tie-down cleat is not seated in the notches, it will not be flush with the rail and cannot be properly tightened. The bolt in the center of the cleat must be tightened hand-tight (20 – 40 inch pounds).
 Check the tightness of the tie-down cleat periodically during a trip to make sure the center bolt has not become loose.
 The channel end stoppers can be used to help prevent cargo from sliding or shifting off the end of the truck bed. They must be installed so they are properly seated in the detents in the channel.
Refer to your Owner’s Manual for loading limits and tie-down recommendations.
030201
070506
0201
0403
04
07
07
0608
05
MAXA/C
FRONT SEAT ADJUSTMENTS
W ITH MANUAL SEATS (if so equipped):
 Pull up on the lever under the front of the seat and slide backward or forward. Release the lever to lock the seat in position.
 Lift the lever on the side of the seat 01 to adjust your seatback backward or forward; release when you have found a comfortable angle and the seat belt fits properly.
 Turn either dial 02 to adjust the angle and height of the seat cushion to the desired position.
W ITH POWER SEATS (if so equipped):
 Move the control forward or backward to adjust the seat cushion forward or backward. 01
 Pull up to raise the seat cushion; press down to lower the cushion. 02
 Push the switch forward to move the seatback forward; push it back to move the seatback backward. 03
Your driver’s seat has a lumbar support; adjust it by moving the lever up or down.
FOLDING THE REAR BENCH SEAT
(Crew Cab only)
FOLDING THE SEATBACK DOWN :
To fold the rear bench seatback down to access the
jacking tools, pull up on the straps located on the
outer edge of the seatbacks 01 and fold the
seatback forward.
FOLDING THE SEAT BASE UP:
To fold the rear bench seat base up to access the
under-seat storage bins:
 Lift up on the lever 01 located on the side of the
seat, while lifting the front of the seat cushion up.
 Fold the bottom of the seat cushion toward the
back of the vehicle until it locks into place.
 Repeat this process to raise and secure the seat
cushion on the other side of the vehicle.
REMOTE KEYLESS ENTRY SYSTEM
(if so equipped)
LOCK DOORS
Press the LOCK button to lock all doors.
UNLOCK DOORS
Press the UNLOCK button once to unlock the driver’s door only. Press the button again within 5 seconds to unlock all doors.
USING THE PANIC ALARM
Press and hold the PANIC button for longer than 0.5 seconds. The panic alarm will sound and the headlights will stay on for 25 seconds. The panic alarm stops when it has run for 25 seconds, or any button is pressed on the keyfob.
SILENCING THE HORN BEEP FEATURE
 To deactivate – Press and hold the LOCK and UNLOCK buttons for at least 2 seconds.
 To activate – Press and hold the LOCK and UNLOCK buttons for at least 2 seconds
once more.
Sh ift_capability
CHILD SAFETY REAR DOOR LOCK
(Crew Cab Model only)
Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the LOCK position, the door can be opened only from the outside.
AD D ITIONAL FEATU R E S (continued)
FOLD FLAT FRONT PASSENGER SEAT
(if so equipped)
To fold the front passenger’s seatback flat for extra storage length when transporting long items:
 Slide the seat to the rear-most position. Lift up on the recline lever, located on the outside edge of the seat, and fold the seatback forward as far as it will go. 01 Then lift up on the latch located on the upper corner of the seatback to release the back of the seat. 02
This easy-to-use Quick Reference Guide is intended to help you more fully appreciate
some of the unique features and functions of your new vehicle. However, it is not
intended to replace your Owner’s Manual. The Owner’s Manual contains more
detailed information to help you better understand the important safety warnings,
features, operation, and maintenance of your vehicle.
QR6E-0D40U2 Printing: April 2006 (06)
Nissan, the Nissan Brand Symbol, “SHIFT_ ” tagline, Z and Nissan model names are Nissan trademarks. ©2006 Nissan North America, Inc.
Sh ift_
02
01
01
02
2006
FRONTI E R

Q U I C K R E F E R E N C E G U I D E

0102
01
01
02
UTILITY BED WITH SPRAY-ON BED LINER
AND UTILI-TRACK ™ SYSTEM
(if so equipped)
The Utili-track™ channel system allows you to move tie-down clamps in the bed to the best location to
secure a load.
 The tie-down cleats must be installed so the clamp is properly seated in the notches in the rail. If the tie-down cleat is not seated in the notches, it will not be flush with the rail and cannot be properly tightened. The bolt in the center of the cleat must be tightened hand-tight (20 – 40 inch pounds).
 Check the tightness of the tie-down cleat periodically during a trip to make sure the center bolt has not become loose.
 The channel end stoppers can be used to help prevent cargo from sliding or shifting off the end of the truck bed. They must be installed so they are properly seated in the detents in the channel.
Refer to your Owner’s Manual for loading limits and tie-down recommendations.
03
AD D ITIONAL FEATU R E S
SEAT BELT WARNING LIGHT AND CHIME
 The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for about 6 seconds unless the driver’s seat belt is securely fastened.
 The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied (if so equipped). For 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger.
Refer to the Owner’s Manual for detailed information regarding seat belt usage.