rims NISSAN FRONTIER 2013 D40 / 2.G Warranty Booklet

B. You must pay for taxes and any additional servicesyou order at the time of adjustment plus any addi-
tional service that may be unique to your application,
e.g. Tire Pressure Monitoring System.
C. You must submit your claim on an approved claim form supplied by an authorized Goodyear or Dunlop
service facility. The form must be filled out com-
pletely and signed, where you the owner or your
authorized agent presented the tire for adjustment.
SAFETY WARNINGS
Property damage, serious injury or death may result
from:
TIRE FAILURE DUE TO UNDERINFLATION/
OVERLOADING/ MISAPPLICATION.
Follow the vehicle owner’s manual or tire placard in
vehicle.
TIRE FAILURE DUE TO IMPACT DAMAGE/ IM-
PROPER MAINTENANCE.
Tires should be inspected regularly by a qualified
technician for signs of damage, such as punctures or
impacts.
TIRE FAILURE DUE TO IMPROPER REPAIRS.
See Rubber Manufacturer’s Association (RMA) es-
tablished repair procedures at www.rma.org and/or
go to www.goodyear.com for information on proper
repair procedures.
EXPLOSION OF TIRE/RIM ASSEMBLY DUE
TO IMPROPER MOUNTING.
Only specially-trained persons should mount tires.
When mounting tires, use safety cage and clip-on
extension air hose to inflate.
FAILURE TO MOUNT RADIAL TIRES ON AP-
PROVED RIMS.
FAILURE TO DEFLATE SINGLE OR DUAL
ASSEMBLIES COMPLETELY BEFORE
DEMOUNTING.
TIRE SPINNING.
On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph) , as
indicated on the speedometer.
EXCESSIVE WHEEL SPINNING.
This can also result in tire disintegration or axle
failure.
WARNING: Vehicle handling, traction, ride comfort and
other performance parameters may be significantly af-
fected by a change in tire size or type. Before replacing
tires, always consult and follow the vehicle owner’s
manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are differ-
ent from the original equipment size make certain: (1)
The tires have adequate load carrying capacity based
on the vehicle placard, (2) The tires have sufficient
inflation pressure to carry the load and (3) There is
proper clearance with no interference points between
the tire and vehicle. The consumer must be aware to
always drive safely and obey all traffic laws. Avoid
sudden, sharp turns or lane changes. Failure to follow
any of these warnings may result in loss of control of the
vehicle, leading to an accident and serious injury or
death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and
performance from your Goodyear or Dunlop tires is to
give them a simple but frequent (at least monthly) in-
spection for proper inflation, even treadwear, and the
presence of any damage.
DO MAINTAIN PROPER INFLATION
PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire
performance, safety and fuel economy. To maintain
proper inflation pressure, frequently (at least monthly)
check tires (when they are cool) with an accurate tire
pressure gauge.*
For example, it is difficult to tell just by looking at radial
tires whether they are underinflated.
Furthermore, when operating a vehicle equipped with
radial tires, it is difficult to notice when a tire has gone
flat or nearly flat since the “feel” of the vehicle does not
change significantly.
*Evidence of air loss or repeated underinflation
always requires expert inspection to determine
the source of leakage and tire removal to deter-
mine repairability. To avoid injury, NEVER attempt to
reinflate a tire that has been run severely underinflated.
Progressive air loss may result from punctures, cuts,
curbing, impacts or partial bead unseating. Some fit-
ment causes for air loss are (1) incomplete bead seat-
ing, (2) bead tearing caused by a machine tool due to
insufficient lubrication or improper adjustment, (3) leak-
ing valve core or rubber valve components. These
should be replaced when problems are detected and
whenever tires are replaced.
(Continued on next page)
26 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

DON’T ATTEMPT TO MOUNT YOUR
OWN TIRES
Serious injury or Death may result from explosion of tire/
rim assembly due to improper mounting procedures.
Follow tire manufacturer’s instructions and match tire
diameter to rim diameter. Mount light truck radials on
rims approved for radial service. Do not apply bead
sealer. This can inhibit bead seating. Lubricate beads
and tire rim (including tube or flap) contact surfaces.
Lock assembly on mounting machine or place in safety
cage. STAND BACK and never exceed 40 psi to seat
beads. Never use a volatile substance or a rubber
“donut” (also known as a bead expander or “O-Ring”) to
aid bead seating. Only specially-trained persons should
mount tires.
DON’T MIX TIRES OF DIFFERENT
SIZES AND TYPES ON THE SAME
AXLE
For optimum handling and control, Goodyear and Dun-
lop recommend fitment of four (4) tires of the same type
and size unless otherwise specified by the vehicle
manufacturer.
WARNING: Before you replace your tires, always con-
sult the vehicle owner’s manual and follow the vehicle
manufacturer’s replacement tire recommendations. Ve-
hicle handling may be significantly affected by a change
in tire size or type. When selecting tires that are different
than the Original Equipment size, see a professional
installer in order to make certain that proper clearance,
load carrying capacity and inflation pressure is selected.
Never exceed the maximum load capacity and inflationpressure listed on the sidewall of the tire. Always drive
safely and obey all traffic laws. Avoid sudden, sharp
turns or lane changes. Failure to follow this warning may
result in loss of control of the vehicle, leading to an
accident and serious injury or death.
When replacing tires, you must maintain the outside
diameter and load carrying capacity of the Original
Equipment tire. Inflation pressure may need to be ad-
justed to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or
JATMA standards for correct load and inflation informa-
tion.
NEVER FIT TIRES TO A VEHICLE THAT
HAVE LESS LOAD CARRYING
CAPACITY THAN AS REQUIRED BY
THE ORIGINAL EQUIPMENT
MANUFACTURER
Examples: Many vehicles, such as large passenger
vans, require Load Range E tires as designated by the
vehicle manufacturer. Fitment of a tire, such as a Load
Range D, with less carrying capacity is not allowed.
In other cases, tires of the same size may carry different
load indexes in the service description. You must make
certain the replacement tires fitted to the vehicle have a
load carrying capacity equal to or greater than what the
Original Equipment manufacturer specifies.
FOLLOW THESE ADDITIONAL
GUIDELINES
Fit newest tires on rear axle. If radials and non-radials
must be fitted to the same vehicle, fit radials on rear axle.Never mix radials and non-radials on the same axle.
When fitting snow tires or all-season tires to perfor-
mance vehicles, always fit in sets of four. It is not
recommended to fit tires with different speed ratings. If
tires with different speed ratings are installed on a
vehicle, they should be installed with like pairs on the
same axle. The speed capability of the vehicle will
become limited to that of the lowest speed rated tires. It
is also recommended that the lower speed rated tires
be placed on the front axle regardless of which axle is
driven to help prevent potential oversteer.
Use of lift kits with some vehicle/tire combinations can
cause instability. When changing tire sizes, always con-
sult Dealer for optimum rim width and carefully checkvehicle/tire clearances.
RETREADED TIRES
Retreaded passenger and light truck tires are not war-
ranted by Goodyear and Dunlop for any reason. Good-
year and Dunlop speed ratings and U.S. Department of
Transportation test compliance certifications are voided
for retreaded tires.
DO MAINTAIN VEHICLE SUSPENSION,
WHEEL ALIGNMENT AND BALANCE
AND ROTATE YOUR TIRES
Lack of rotation, worn suspension parts, underinflation/
overinflation, wheel imbalance and misalignment can
cause vibration or irregular tire wear. Rotate your tires
according to your vehicle manufacturer’s recommenda-
tions or at maximum intervals of 6,000 miles/10,000 km.
(Continued on next page)
28
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

WHAT IS NOT COVERED BY THIS
LIMITED WARRANTY
(1)Mileage is not warranted.
(2) Damage due to road hazards, whether repair- able or not (such as cut, snag, bruise, impact
break, bulge, puncture, improper use of tire
chains, stone drill, chip, scale) . These types of
damages or air loss always require tire re-
moval and inspection by a qualified tire
professional.
(3) Irregular tread wear or rapid tread wear due to failure to rotate the tires at recommended in-
tervals or from vehicle misalignment.
(4) Damage resulting from improper repair materi- als or procedures such as rope type plugs.
Toyo does not warrant any inspection or repair
process. The repair is entirely the responsibil-
ity of the repairer and should be made in ac-
cordance with procedures as specified by the
Rubber Manufacturers Association (RMA) .
(5) Damage from incorrect mounting or dismount- ing of the tire, incorrect wheel size, water or
other material trapped inside the tire during
mounting or failure to balance the tires. (6) Damage or uneven tread wear from incorrect
inflation, overloading, fire, theft, defective me-
chanical conditions such as brakes, shocks,
rims, wreck or collision, misuse,
misapplication, negligence, willful damage or
abuse, vandalism, tire alteration, tire spinning,
racing or competition purposes.
(7) Damage, corrosion or rubber deterioration due to the use of oil-based chemicals, water-
based sealers, balancing substances, or flam-
mable gases.
(8) Uniformity problems such as ride, balance and vibration complaints after the first 25% of
tread wear.
(9) Replacement of four (4) or more tires from the same vehicle will not be accepted for ride dis-
turbance complaints i.e. vibration, out of
round, out of balance, pulling, noise, due to
the unlikely event of multiple tires with unifor-
mity problems.
(10) Claims for weather/ozone cracking after 5 years from the date of manufacture.
(11) Any tire which has been run with low air pres- sure or while flat.
(12) Tires used in commercial service.
(13) Tires on vehicles regularly operated outside the United States. (14) Claims made by anyone other than the original
retail purchaser of the vehicle.
(15) Tires with the D.O.T. identification number re- moved or rendered illegible.
(16) Any tire not presented and available for Toyo’s inspection.
(17) Any tire for which mileage and tire rotation records are not available or verifiable.
(18) Any tires worn beyond the wear bars (less than 2/32nds of an inch of tread remaining) .
(19) Tires not supplied as original equipment on new vehicles (refer to Owner’s Manual for
coverage) .
(20) “T” Type temporary spare tires used at speeds over 50 miles per hour, exhibiting such
damage.
(21) Dealer service charges are not covered for routine or required maintenance of the tires
such as alignments, rotation or balancing.
(22) The cost of applicable federal, state and local taxes and fees.
(23) Retreaded passenger and light truck tires are not warranted.
(Continued on next page)
TOYO TIRE LIMITED WARRANTY 37

TREAD WEAR INDICATORS (WEAR BARS):Tires
contain Tread Wear Indicators (Wear Bars) in the
grooves of the tire tread which show up when only
2/32nds of an inch (1.6mm) of tread is remaining.
At this stage, your tires must be replaced. Tires
worn beyond this stage are dangerous.
* Provided by and published at the request of the tire
manufacturers/warrantors.
HAZARDS
Objects in the road that threaten a tire should be safely
avoided. These objects are potholes, glass, metal,
rocks, wood debris and the like. Unavoidable contact
should prompt a thorough tire inspection.
You may not always recall hitting an object that can
damage or injure your tires. If while driving your vehicle
experiences any unusual vibrations, ride disturbance or
noise and/or you suspect that possible damage to the
tires or vehicle has occurred, DO NOT JAM OR LOCK
YOUR BRAKES! Rather reduce your speed and drive
with caution until you can safely pull off the road. Stop
and inspect the tires. If the tire is underinflated or
damaged, deflate, remove the tire and rim assembly and
replace it with your spare. If you cannot detect a cause,
have the vehicle towed to the nearest vehicle or tire
dealer to have the vehicle inspected.
REPAIRING, MOUNTING AND
DEMOUNTING OF TIRES
Do not attempt to repair, mount or demount a tire
yourself. Tire changing can be dangerous and must be
done by professionally trained persons using proper
tools and procedures as specified by the Rubber Manu-
facturers Association (RMA) . Follow these mounting
recommendations. Your tires should be mounted on
wheels of correct size and type and which are in good,
clean condition. Bent, chipped or rusted wheels may
cause tire damage. The inside of the tire must be free
from foreign materials. Have your dealer check the
wheels before mounting new tires. Mismatched tires
and rims can explode during mounting. Also, mis-
matched tires and rims can result in dangerous tire
failure on the road. If a tire is mounted by error on the
wrong-sized rim, do not remount it on the proper rim -
scrap it. It may be damaged internally (which is not
externally visible) by being dangerously stretched and
could fail on the highway.
Old valves may leak. When new tubeless tires are
mounted, have new valves of the correct type installed.
Tubeless tires must be mounted only on wheels de-
signed for tubeless tires, i.e., wheels which have safety
humps or ledges.
Never perform a temporary repair, use an innertube or
inject sealant as a permanent substitute for a proper
repair. Only qualified persons should repair tires.
Be sure that all your valves have suitable valve caps.
This will keep valve cores clean and clear and guard
against leakage. REPAIRS - WHENEVER POSSIBLE, SEE A TIRE
DEALER AT ONCE.
Some tire manufacturers do not
warrant any inspection or repair process. The repair is
entirely the responsibility of the repairer. Punctures in
the tread of a passenger tire which do not exceed 1/4 of
an inch (6mm) in diameter can usually be repaired by
following the Rubber Manufacturer’s Association
(RMA) Passenger and Light Truck Repair procedures.
Contact the manufacturer of your tires for its position
and assistance as to the acceptable location for a
proper repair and the repair of speed rated tires. Do not
use plug repairs. They may cause further damage
to the tire. They are not always air tight and the
plug may fail. Do not exceed posted speed limits on
any repaired tire. Certain tire manufacturers speed rat-
ings are voided if the tire is repaired.
Although a tire was properly repaired, internal structural
damage resulting from the puncture may have occurred.
Sometime later the damage may cause the tire to be
removed from service.
If the tire has a puncture in the tread which exceeds
1/4 inch (6mm) , the tire must be replaced. If any tire has
sustained a puncture, have the tire inspected internally
by a tire dealer for possible damage that may have
occurred.
Improper mounting and inflation procedures can cause
an explosion of the tire/rim assembly. Only specially
trained persons should perform these tasks. Contact
your tire store or dealer for assistance.
CAUTION -Never, under any circumstance, intro-
duce a flammable substance into a tire.
(Continued on next page)1 Provided by and published at the request of the tire manufacturers/warrantors.
IMPORTANT TIRE SAFETY INFORMATION143