fuel pressure NISSAN FRONTIER 2016 D23 / 3.G Warranty Booklet

HOW DO YOU OBTAIN AN
ADJUSTMENT?
A. You must present the tire to be adjusted to anauthorized Goodyear or Dunlop service facility. Tires
replaced on an adjustment basis become the prop-
erty of The Goodyear Tire & Rubber Company,
Goodyear Dunlop Tires North America, Ltd. or
Goodyear Canada Inc.
B. You must pay for taxes and any additional services you order at the time of adjustment plus any addi-
tional service that may be unique to your application,
e.g., Tire Pressure Monitoring System.
C. You must submit your claim on an approved claim form supplied by an authorized Goodyear or Dunlop
service facility. The form must be filled out com-
pletely and signed, where you the owner or your
authorized agent presented the tire for adjustment.
You must go to an authorized Goodyear or Dunlop
outlet for replacement tires and all warranty service.
SAFETY WARNINGS
Property damage, serious injury or death may result
from:
TIRE FAILURE DUE TO UNDERINFLATION/
OVERLOADING / MISAPPLICATION.
Follow the vehicle owner’s manual or tire placard in
vehicle.
TIRE FAILURE DUE TO IMPACT DAMAGE /
IMPROPER MAINTENANCE.
Tires should be inspected regularly by a qualified
technician for signs of damage, such as punctures or
impacts.
TIRE FAILURE DUE TO IMPROPER REPAIRS.
See Rubber Manufacturers Association (RMA) es-
tablished repair procedures at www.rma.org and/or
go to www.goodyear.com for information on proper
repair procedures.
EXPLOSION OF TIRE/RIM ASSEMBLY DUE
TO IMPROPER MOUNTING.
Only specially trained persons should mount tires.
FAILURE TO MOUNT RADIAL TIRES ON
APPROVED RIMS.
FAILURE TO DEFLATE SINGLE OR DUAL
ASSEMBLIES COMPLETELY BEFORE
DEMOUNTING.
TIRE SPINNING.
On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph) , as
indicated on the speedometer.
EXCESSIVE WHEEL SPINNING.
This can also result in tire disintegration or axle
failure.
WARNING: Vehicle handling, traction, ride comfort and
other performance parameters may be significantly af-
fected by a change in tire size or type. Before replacing
tires, always consult and follow the vehicle owner’s
manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are differ-
ent from the original equipment size make certain: (1)
The tires have adequate load-carrying capacity based
on the vehicle placard, (2) The tires have sufficient
inflation pressure to carry the load and (3) There is
proper clearance with no interference points between
the tire and vehicle. The consumer must be aware to
always drive safely and obey all traffic laws. Avoid
sudden, sharp turns or aggressive lane changes. Failure to follow any of these warnings may result in loss of
control of the vehicle, leading to an accident and serious
injury or death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and
performance from your Goodyear or Dunlop tires is to
give them a simple but frequent (at least monthly) in-
spection for proper inflation, even treadwear and the
presence of any damage.
DO MAINTAIN PROPER INFLATION
PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire
performance, safety and fuel economy. Check inflation
pressures at least once a month and before long trips.
Use an accurate tire pressure gauge. Always check
pressures when the tires are cold (when the vehicle has
been driven less than one mile) . If you must check
inflation when the tires are hot, add 4 psi (27 kPa) to the
recommended cold inflation pressure. It is difficult to tell
just by looking at radial tires whether they areunderin-
flated.*
Furthermore, when operating a vehicle equipped with
radial tires, it is difficult to notice when a tire has gone
flat or nearly flat since the “feel” of the vehicle does not
change significantly.
*Evidence of air loss or repeated underinflation
always requires expert inspection to determine
the source of leakage and tire removal to deter-
mine repairability.
To avoid injury, NEVER attempt to
reinflate a tire that has been run severely underinflated.
Progressive air loss may result from punctures, cuts,
(Continued on next page)
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY 27

curbing, impacts or partial bead unseating. Some fit-
ment causes for air loss are (1) incomplete bead seat-
ing, (2) bead tearing caused by a machine tool due to
insufficient lubrication or improper adjustment. Leaking
valve core or rubber valve components should be re-
placed when problems are detected and whenever tires
are replaced.
Always maintain inflation pressure at the level
recommended by the vehicle manufacturer as
shown on the vehicle placard, vehicle certifica-
tion label or in the vehicle owner’s manual:
Underinflation is the leading cause of tire failure and may
result in severe cracking, component separation or
“blowout.” It reduces tire load capacity, allows exces-
sive sidewall flexing and increases rolling resistance,
resulting in heat and mechanical damage. Maintaining
proper inflation pressure is the single most important
thing you can do to promote tire durability and maximize
tread life.
Overinflation increases stiffness, which may deteriorate
ride and generate unwanted vibration. Overinflation also
increases the chances of impact damage.
DON’T OVERLOAD YOUR VEHICLE
Check your vehicle owner’s manual to determine the
load limits. Overloading your vehicle places stress on
your tires and other critical vehicle components. Over-
loading a vehicle can cause poor handling or increased
fuel consumption and may cause tire failure. Overload-
ing your tires can result in severe cracking, component
separation or “blowout.”
Never fit your vehicle with new tires that have less load
capacity than shown on the vehicle tire placard andremember that optimum rim width is important for
proper tire load distribution and function. The maximum
load capacity stamped on the sidewalls of P-Metric &
European Metric tires is reduced by 10% when used on
a light truck, utility vehicle or trailer. Never fit P-Metric or
European Metric tires to light trucks that specify LT-type
replacement tires.
DON’T SPIN YOUR TIRES
EXCESSIVELY
Avoid excessive tire spinning when your vehicle is stuck
in snow, ice, mud or sand. The centrifugal forces gen-
erated by a free-spinning tire/wheel assembly may
cause sudden tire explosion, resulting in vehicle dam-
age and/or serious personal injury to you or a bystander.
Never exceed 35 mph/55 kph, as indicated on your
speedometer. Use a gentle backward and forward rock-
ing motion to free your vehicle for continued driving.
Never stand near or behind a tire spinning at high
speeds, for example, while attempting to push a vehicle
that is stuck or when an on-the-car spin balance ma-
chine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when they reach two
thirty-seconds of an inch (2/32) remaining tread depth.
All new tires have treadwear indicators which appear as
smooth banks in the tread grooves when they wear to
the two thirty-seconds of an inch (2/32) level. Many wet
weather accidents result from skidding on bald or nearly
bald tires. Excessively worn tires are also more suscep-
tible to penetrations.
DO CHECK YOUR TIRES FOR DAMAGE
Frequent (at least monthly) inspection of your tires for
signs of damage and their general condition is important
for safety. If you have any questions, have your tire
Dealer inspect them. Impacts, penetrations, cracks,
knots, bulges or air loss always require tire removal and
expert inspection. Never perform a temporary repair or
use an inner tube as a substitute for a proper repair.
Only qualified persons should repair tires.
PROPER TIRE REPAIR
NOTE: Goodyear does not warrant any inspection or
repair process. The repair is entirely the responsibility of
the repairer and should be made in accordance with
established Rubber Manufacturers Association (RMA)
procedures.
TIRE PRESSURE MONITORING
SYSTEM ALERT
Refer to your vehicle Owner’s Manual for more informa-
tion on what to do if the tire pressure warning system
activates.
THE CONVENIENCE (TEMPORARY)
SPARE
The Convenience (Temporary) Spare is designed, built
and tested to the high engineering standards set by
North America’s leading car manufacturers and to
Goodyear’s own high standards of quality control. It is
designed to take up a minimum of storage space and, at
the same time, fulfill the function of a spare tire when
needed. The spare is kept in its storage space, fully
(Continued on next page)
28
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

inflated at 60 psi. To be sure it is always ready for use,
the air pressure should be checked on a regular basis.
The Convenience (Temporary) Spare can be used in
combination with the original tires on your vehicle. You
can expect a tire tread life of up to 3,000 miles
(4,800 kilometers), depending on road conditions and
your driving habits. To conserve tire tread life, return the
spare to the storage area as soon as it is convenient to
have the standard tire repaired or replaced.
The Convenience (Temporary) Spare weighs less than a
standard tire so it’s easier to handle. It also helps reduce
the total car weight, which contributes to fuel economy.
The wheels used with the Convenience (Temporary)
Spare are specifically designed for use with high pres-
sure spares and should never be used with any other
type tire.
DON’T ATTEMPT TO MOUNT YOUR
OWN TIRES
Serious injury or death may result from explosion of
tire/rim assembly due to improper mounting proce-
dures. Follow tire manufacturer’s instructions and
match tire diameter to rim diameter. Mount light truck
radials on rims approved for radial service. Do not apply
bead sealer. This can inhibit bead seating. Lubricate
beads and tire rim (including tube or flap) contact
surfaces. Lock assembly on mounting machine or place
in safety cage. STAND BACK and never exceed 40 psi
to seat beads. Never use a volatile substance or a
rubber “donut” (also known as a bead expander or
“O-Ring”) to aid bead seating. Only specially trained
persons should mount tires.
DON’T MIX TIRES OF DIFFERENT
SIZES AND TYPES ON THE SAME
AXLE
For optimum handling and control, Goodyear recom-
mends fitment of four (4) tires of the same type and size
unless otherwise specified by the vehicle manufacturer.
WARNING: Before you replace your tires, always con-
sult the vehicle owner’s manual and follow the vehicle
manufacturer’s replacement tire recommendations. Ve-
hicle handling may be significantly affected by a change
in tire size or type. When selecting tires that are different
from the Original Equipment size, see a professional
installer in order to make certain that proper clearance,
load-carrying capacity and inflation pressure are se-
lected. Never exceed the maximum load capacity and
inflation pressure listed on the sidewall of the tire. Al-
ways drive safely and obey all traffic laws. Avoid sudden,
sharp turns or aggressive lane changes. Failure to fol-
low this warning may result in loss of control of the
vehicle, leading to an accident and serious injury or
death.
When replacing tires, you must maintain the outside
diameter and load-carrying capacity of the Original
Equipment tire. Inflation pressure may need to be ad-
justed to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or
JATMA standards for correct load and inflation informa-
tion.
NEVER FIT TIRES TO A VEHICLE THAT
HAVE LESS LOAD CARRYING
CAPACITY THAN AS REQUIRED BY
THE ORIGINAL EQUIPMENT
MANUFACTURER
Examples: Many vehicles, such as large passenger
vans, require Load Range E tires as designated by the
vehicle manufacturer. Fitment of a tire, such as a Load
Range D, with less carrying capacity is not allowed.
NOTE: Goodyear-manufactured and/or marketed
European-Metric and P-Metric passenger tires are in-
terchangeable as long as they have the same section
width, same aspect ratio and same rim diameter.Cau-
tion: Never substitute a “Standard Load” (SL) tire
for an Extra Load (XL) orReinforced tire. If the
vehicle was originally equipped with “Extra
Load” (XL) or Reinforcedtires, replace those
tires with similar sized Extra Load(XL) orRe-
inforced tires.
FOLLOW THESE ADDITIONAL
GUIDELINES
When installing only two tires, fit the tires with the
deepest tread depth on the rear axle. If radials and
non-radials must be fitted to the same vehicle, fit radials
on rear axle. Never mix radials and non-radials on the
same axle. When fitting winter tires or all-season tires to
performance vehicles, always fit in sets of four. It is not
recommended to fit tires with different speed ratings. If
tires with different speed ratings are installed on a
vehicle, they should be installed with like pairs on the
same axle. The speed capability of the vehicle will
become limited to that of the lowest speed rated tires.
(Continued on next page)
GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
29

occurring, and proof of maintenance records should be
kept. The owner(s) should have the tires rebalanced if
vibration is experienced, and the vehicle’s alignment
should be checked if uneven or rapid wear is occurring,
or when suggested by the vehicle’s manufacturer.
All warranty claims must be presented to an authorized
Falken dealer or participating car dealership. The own-
er(s) must present any supporting maintenance records
and documentation necessary to help determine if the
tire(s) in question are deemed covered by the limited
warranty or not.
LEGAL RIGHTS
All implied warranties, including warranties of mer-
chantability and fitness for a particular purpose shall be
limited in duration to the above period. To the extent
permitted by law, Falken Tire Corporation shall not be
responsible for incidental or consequential damages,
such as loss of use of the tire or the vehicle on which it
is used, inconvenience, or commercial loss, some states
do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of incidental or con-
sequential damages, so the above limitations or exclu-
sions may not apply to you. This warranty gives you
specific legal rights and you may also have other rights,
which vary from state to state. This is the only express
warranty applicable to Falken brand tires and super-
sedes the terms of any previous warranty. Falken neither
assumes nor authorizes anyone to make or assume for it
any other warranty.
TIRE CARE AND RECOMMENDATIONS
PROPER INFLATION and FUEL ECONOMY*
Ensure maximum performance and a long life from your
tires by checking the air pressures at least once a month
and set them to the vehicle manufacturer’s recom-
mended pressure(s) listed on the vehicle’s tire placard
or in your owner’s manual. Always check and adjust your
air pressure when your tires are cold, preferably first
thing in the morning before driving. Never release air
pressure from tires when they are hot. Wait until the tires
cool down and recheck, adding air or releasing as
required. Falken endorses the use of nitrogen in your
tires because it helps your tires maintain optimal pres-
sure for longer periods of time and reduces the amount
of moisture inside of the tire and wheel assembly.
TIRE INFLATION PRESSURE
Tires need to be properly inflated to effectively operate
and perform as intended. Tires carry the weight of the
vehicle, passengers, and cargo as well as bear the
forces of braking, accelerating, and turning. The vehicle
manufacturer sets the inflation pressures for the original
equipment tires that are on your vehicle.
Driving with improperly inflated tires is dangerous. An
under inflated tire will generate excessive heat build-up
that will cause damage to the internal structure and
inner liner of the tire. Besides tire damage, improper tire
inflation pressures can also affect your vehicle’s ride
and handling, tire tread wear, and fuel economy. It is
recommended to always keep all of your tires, including
the spare, at the vehicle manufacturer’s recommended
inflation pressures and be sure to check the air pressuremonthly and before going on long road trips or carrying
extra weight in your vehicle.
Your vehicle’s tire placard and/or owner’s manual will
list the cold inflation pressure(s) for your vehicle’s origi-
nal equipment tires, including the spare. The placard
can be found on the driver’s side door or door jamb area.
If you have questions about understanding your vehi-
cle’s tire placard, please refer to your owner’s manual or
ask a qualified tire service professional.
●For detailed information on TIRE INFLATION PRES-
SURE please visit www.Falkentire.com
CHECKING YOUR TIRE’S AIR PRESSURE
Checking your air pressure at least once a month is vital
to help your tires perform properly and help you get the
best gas mileage possible. Tires can lose up to 7 kPa
(1 psi) per month under normal conditions and lose up
to 7 kPa (1 psi) per every 9°C (16°F) drop in tempera-
ture. Here are some simple steps on how to check the
air pressures in your tires: 1. Remove the valve stem cap.
2. Place the end of the tire gauge firmly against the tire’s valve stem.
3. Read the current pressure displayed on the gauge that is currently in the tire.
4. Increase pressure at this time (if needed) and re- check with your tire gauge.
5. Replace the valve stem cap.
6. Repeat until all of your tires have been checked and adjusted accordingly.
(Continued on next page)
* Some plus size applications may require different air pressure(s) than what is listed on your vehicle’s placard or owner’s manual. In this case, please consult your tire dealer or Falken Tire
for proper inflation pressure(s) .
FALKEN TIRE LIMITED WARRANTY 51

WARRANTY PARTS LISTFuel injection system
Engine control module/onboard diagnostic deviceOxygen sensor(s)Mass air flow sensorIntake manifoldThrottle body
Catalytic converter (including selective catalytic re-
duction and diesel oxidation catalysts)
Exhaust manifold(s)Exhaust tube from manifold to catalytic converter
Front exhaust tube with catalytic converter perma-
nently attached
Camshaft position sensor(s)Crankshaft position sensor(s)Spark plugs, ignition coil and wiresIgnition control module
Exhaust manifold with catalytic converter perma-
nently attached
Diesel Exhaust Fluid SystemDiesel Particulate FilterCharge Air Cooler (Diesel)Fuel Supply Manifold (Diesel)High Pressure Fuel Pump (Diesel)Turbocharger(s)Evaporative emission control systemFuel filler neck restrictor and check valveFuel tank and filler cap
Idle air control systemPositive crankcase ventilation systemExhaust gas recirculation (EGR) control systemPulsed secondary air injection system and valvesHoses, clamps, fittings, tubing, sealing gaskets or
devices and mounting hardware used in above sys-
tems
Vacuum and temperature sensitive valves and
switches used in above systems
Electronic sensors and controls used in above sys-
tems
The Emission Performance or Defect Warranty
may be subject to future governmental adminis-
trative action. Nissan reserves the right to
change the terms of the warranty to be consis-
tent with these actions. See your dealer for infor-
mation regarding possible changes.
o = Long Term Federal Emission Parts covered for 96 months/or 80,000 miles, except for TITAN Diesel.
FEDERAL VEHICLE EMISSION CONTROL LIMITED WARRANTIES

LONG-TERM EMISSION SYSTEM
DEFECTS WARRANTY PARTS LIST
EGI Wiring Harness
Fuel Tank
Engine Control Module
o
Throttle Body
Evaporative Emission Canister
Intake Manifold
Intake Manifold Collector
Exhaust Tube W/ Catalytic Converter
o
Ehaust Manifold
Front Exhaust Tube W/ Catalytic Converter
o
Front Exhaust Tube
Center Exhaust Tube
Three-Way Catalyst
o
Diesel Catalyst and Particulate Filter
Selective Catalyst Reduction Assembly
Flywheel
Signal Plate
Torque converter Drive Plate
Transmission Control Module
Knock Sensor
Mass Air Flow Sensor
Turbocharger
Turbocharger Speed Sensor
Charge Air Cooler
Crankcase Breather
Diesel Exhaut Fluid Tank
EGR Valve
EGR Cooler
Fuel Injector
Fuel Supply Manifold Assembly
High-Pressure Fuel Tube Assembly
High-Pressure Fuel Pump
Water Control Valve
TITAN
DieselXXX
X XXX XXXXXXXXXXX
o = Long Term Federal Emission Parts covered for 96 months or 80,000 miles, except for the Cummins Diesel TITAN
oo = This part repair is less than the California high cost threshold; however, it is classified as a Long Term Federal Emission Part and is covered for 96 months or 80,000 miles, whichever
comes first.
CALIFORNIA VEHICLE EMISSION CONTROL WARRANTIES1, 2

LIMITATION OF WARRANTIES AND OTHER
WARRANTY TERMS AND STATE LAW
RIGHTS
EXTRA EXPENSES - LIMITATIONS OF DAMAGES
This warranty does not cover incidental or
consequential damages such as loss of the
use of the vehicle, inconvenience or commer-
cial loss.
ANY IMPLIED WARRANTY OF MERCHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PUR-
POSE SHALL BE LIMITED TO THE DURATION
OF THIS WRITTEN WARRANTY.
Some states do not allow the exclusion or limitation
of incidental or consequential damages or limita-
tions on how long an implied warranty lasts, so the
above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights,
and you may also have other rights which vary from
state to state.
Nissan
1does not authorize any person to create for
it any other warranty, obligation or liability in con-
nection with this vehicle.
WARRANTY PARTS LISTFuel injection system
Engine control module/onboard diagnostic deviceOxygen sensor(s)Mass air flow sensorIntake manifoldThrottle body
Catalytic converter (including selective catalytic re-
duction and diesel oxidation catalysts)
Exhaust manifold(s)Exhaust tube from manifold to catalytic converter
Front exhaust tube with catalytic converter perma-
nently attached
Camshaft position sensor(s)Crankshaft position sensor(s)Spark plugs, ignition coil and wiresIgnition control module
Exhaust manifold with catalytic converter perma-
nently attached
Diesel Exhaust Fluid SystemDiesel Particulate FilterCharge Air Cooler (Diesel)Fuel Supply Manifold (Diesel)High Pressure Fuel Pump (Diesel)Turbocharger(s)Evaporative emission control systemFuel filler neck restrictor and check valveFuel tank and filler capIdle air control system
Positive crankcase ventilation systemExhaust gas recirculation (EGR) control systemPulsed secondary air injection system and valvesHoses, clamps, fittings, tubing, sealing gaskets or
devices and mounting hardware used in above sys-
tems
Vacuum and temperature sensitive valves and
switches used in above systems
Electronic sensors and controls used in above sys-
tems
The Emission Performance or Defect Warranty
may be subject to future governmental adminis-
trative action. Nissan reserves the right to
change the terms of the warranty to be consis-
tent with these actions. See your dealer for infor-
mation regarding possible changes.
o = Long Term Federal Emission Parts covered for 96 months/or 80,000 miles, except for TITAN XD models (Gas and Diesel) .
FEDERAL VEHICLE EMISSION CONTROL LIMITED WARRANTIES

LONG-TERM EMISSION SYSTEM
DEFECTS WARRANTY PARTS LIST
EGI Wiring Harness
Fuel Tank
Engine Control Module
o
Throttle Body
Intake Manifold
Exhaust Manifold w/Catalytic Converter
o
Front Exhaust Tube w/Catalytic Converter
o
Diesel Catalyst and
Particulate Filter Assembly
Selective Catalyst Reduction Assembly
Torque Converter Drive Plate
Transmission Control Module
Turbocharger
Turbocharger Speed Sensor
Charge Air Cooler
Crankcase Breather
Diesel Exhaust Fluid Tank
EGR Valve
Fuel Injector
Fuel Supply Manifold Assembly
High-Pressure Fuel Tube Assembly
High-Pressure Fuel Pump
Low Pressure Turbocharger
oo
EGR Cooler
oo
Cylinder Head Gasket
oo
TITAN
GasXX X XXX X X
TITAN XD
GasXX X XXX X X
TITAN XD
DieselXXX X XX XXXXXXXXXXXXXX
o = Long Term Federal Emission Parts coverd for 96 months or 80,000 miles, except TITAN XD models (Gas and Diesel) .
oo = Warranty coverage of 120 months or 150,000 miles, whichever comes first.
CALIFORNIA VEHICLE EMISSION CONTROL WARRANTIES1, 2