engine NISSAN GT-R 1998 Repair Manual

TROUBLE DIAGNOSES
Stall Test (Cont'd)
JUDGEMENT OF STALL SPEED
5. Depress accelerator pedal gradually while depressing brake
pedal.
6. Read stall speed quickly, and immediately release accelerator
pedal.
CAUTION: Do not
depress accelerator pedal for more than 5 seconds
when testing.
7. Move selector lever to "N" position.
8. Cool down fluid.
CAUTION:
Run engine at idle
for at least one minute.
Specification:
RB20DE 2,300 - 2,500 rpm
RB25DE 2,350 - 2,550 rpm
RB25DET 2,920 - 3,170 rpm
7 Lever position
Stall
speed status Possible causes
Forward
clutch
Forward one-way clutch
Low one-way clutch
Engine and torque converter one-way clutch
7-
0
Line pressure circuit (line pressure drop), forward clutch, low one-way clutch
and forward one-way clutch
Line pressure circuit (line pressure drop), reverse clutch and forward clutch
Forward clutch, low one-way clutch, forward one-way clutch, reverse clutch
and forward clutch
Line pressure circuit (line pressure drop), forward clutch, low one-way clutch,
forward one-way clutch, reverse clutch and
forward clutch
Clutches and brake are normal except high clutch, brake band, and overrun
It
I
0
0 0 Low & reverse brake
Reverse clutch
0: Within stall speed specification
H: Higher than stall speed specification
L: Lower than stall speed specification
0 0 0 clutch. (However, status of high clutch, brake band, and overrun clutch cannc
be confirmed by stall test.)

TROUBLE DIAGNOSES
DESCRIPTION
CONSULT indicates operation timing of each solenoid such as electrical shift timing and lock-up timing.
Therefore, when there is a definite difference between shift timing detected from shift shock (or engine
speed variation) and the one indicated by CONSULT, mechanical parts other than solenoids and sensors
(including hydraulic circuit) may be malfunctioning. In this case, check the mechanical parts using appli-
cable diagnostic procedures.
Shift schedule (which implies gear position) displayed on CONSULT and that indicated in Service Manual
may differ slightly. This occurs because of the following reasons:
Actual shift schedule has more or less tolerance or allowance.
Shift schedule indicated in Service Manual refers to the point where shifts start, and gear position dis-
played on CONSULT indicates the point where shifts are completed.
Shift solenoid valve A or B (ON/OFF) is displayed on CONSULT at the start of shifting. Gear position
is displayed upon completion of shifting (which is computed by TCM).
To make sure the part No. of ECM-TCM on CONSULT, touch "ENGINE" to verify "C/U PART NUMBER".
SELF-DIAGNOSIS PROCEDURE
Refer to "CONSULT Instruction Manual - Supplement" in details.
1. Turn ignition switch OFF.
2. Connect CONSULT connector to data link connector.
3. Start engine.
4. Touch "START', "NT and "SELF-DIAG RESULTS" sequen-
tially on CONSULT screen.
5. Self-diagnosis results are displayed on the screen.

TROUBLE DIAGNOSES
CONSULT (Cont'd)
SELF-DIAGNOSTIC RESULTS MODE
Diagnostic item 1 Diagnostic item is detected when ... Inspection item - -- -
I TCM does not receive vehicle speed sensor 1 signal due to
open circuit, etc.
TCM receives improper signal during driving. After ignition switch is turned ON, vehicle speed sensor 2 receives improper signal until vehicle starts to run.
VHCL
SPEED
SEN.A/T Vehicle
speed sensor 1 circuit
TCM does not receive vehicle speed sensor 2 signal due to
open circuit, etc.
TCM receives improper signal during driving.
VHCL
SPEED
SEN.MTR Vehicle
speed sensor 2 circuit
TCM detects
folfowing conditions during driving (Except N and
P positions). 0 Excessively high throttle position sensor signal voltage Excessive1 low throttle position sensor signal voltage with idle
switch OF; or full switch ON
THROTTLE
POSl
SEN
Throttle position sensor circuit
SHIFT SOLENOIDN A
SHIFT SOLENOIDN B Shift
solenoid A circuit
Shift solenoid
B circuit
Overrun clutch solenoid circuit
TIC
CLUTCH SOW
I
OVERRUN CLUTCH SN
Lock-up solenoid circuit Specified voltage is not applied to solenoid due to open and/or
short circuit.
LINE
PRESSURE SN
I Line pressure solenoid circuit
0 Excessively low supply voltage to TCM during driving
Excessively high si nal voltage of AIT fluid temperature sensor
(excessively low d fluid temperature) during driving This message is displayed only when malfunction occurs with ignition switch ON, and does not have memory func-
tion.
fluid temperature sensor circuit,
TCM power supply circuit, or
throttle position sensor power sup-
ply circuit
BATT/FLUID
TEMP SEN
ENGINE SPEED SIG
I Excessively low engine speed during driving Engine speed
signal circuit
Turbine sensor circuit
TURBINE
SENSOR
(Except
RB20DE)
SHIFT SOLENOIDN C
(Except
RB20DE)
TCM does not receive input shaft speed sensor signal due to
open circuit,
etc.
0 TCM receives improper signal during driving.
0 TCM does not receive shift solenoid A pressure detection switch
signal due to open
andfor short circuit. Shift solenoid A pressure
detection
switch circuit
MANUAL MODE SW
(Except
RB20DE)
TCM does not receive proper manual mode switch signal due to
open and/or short circuit. Manual
mode switch circuit
ENGINE BRAKE
C/U'1
(Except
RB20DE)
Shift control unit does not operate properly due to open and/or
short circuit of each
input/output signal wire.
Malfunction occurs in shift control unit. Each
signal wire circuit connected
to shift control unit
'INITIAL START*
Power supply to TCM is shut down, and self-diagnostic memory
function is canceled due to battery removal, etc.
CONTROL UNIT (RAM)
I Malfunction is detected in TCM memory (RAM) function.
CONTROL
UNIT
(ROM)
I Malfunction is detected in TCM memory (ROM) function.
'1 : Indicates shift control unit.
DATA MONITOR PROCEDURE
Refer to "CONSULT Instruction Manual - Supplement" and "CON-
SULT Service Manual
- Supplement" in details.
1. Turn ignition switch OFF.
2. Connect CONSULT connector to data link connector.
3. Turn ignition switch ON.
4. Touch "START', ''AT and "DATA MONITOR" sequentially on
CONSULT screen.

TROUBLE DIAGNOSES
CONSULT (Cont'd)
DATA MONITOR MODE (M)
1 I Monitor item
I
tem Display ECU
input Main
signals
-
Description Remarks
signals
VHCUS
SE.A'T
[kmlh] or [mph]
I-
Vehicle speed computed from When
racing engine in "Nn or "P" signal of revolution sensor is position
with vehicle stationary,
displayed. CONSULT
data may not indicate
0 kmlh (0 mph).
Vehicle speed computed from Vehicle
speed display may not be
signal of vehicle speed sensor accurate under approx. 10 kmlh
is displayed. (6 mph). It may not indicate 0
kmlh (0 mph) when vehicle is sta-
tionary.
Throttle position sensor signal
voltage is displayed.
AlT fluid temperature sensor
signal voltage is displayed.
Signal voltage lowers as fluid
temperature rises.
Source voltage of TCM is dis-
played.
Engine speed, computed from Engine speed display
may not be
engine speed signal, is
dis- accurate under approx. 800 rpm.
played. It
may not indicate
0 rpm even
when engine is not running.
Turbine revolution computed Error
may occur under approx.
from signal of turbine revolution 800 rpm and will not indicate
0
sensor is displayed. rpm even if engine is not running.
ONIOFF state computed from
signal of overdrive control SW
is displayed.
ONIOFF state computed from
signal of PIN position SW is
displayed.
ONIOFF state computed from
signal of
R position SW is dis-
played.
ONIOFF state computed from
signal of D position SW is dis-
played.
ONIOFF status, computed from
signal of 2 position SW, is dis-
played.
signal of
1 position SW, is dis-
displayed. ASCD is mounted.
ON
... Cruising state
OFF ... Normal running state
Vehicle
speed sensor
1 (All) (Revolution sensor)
Vehicle speed sensor
2 (Meter) VHCUS SE,MTR
[kmk] or
[rnph]
Throttle position sensor
ITHRTLPOS SEN
I ,
AT fluid temperature sensor
PI
FLUID TEMP SE
Battery voltage
A
Engine speed ENGINE SPEED
[rpml
Turbine revolution sensor
TURBINE REV
[rpml
I
Overdrive control switch
OVERDRIVE SW
[ONIOFFJ
I
PIN position switch
PIN POSI SW
[ONlOFF]
R position switch
R POSITION SW
[OWOFF]
I
2 position switch
1
2 POSITION SW
[ONIOFF]
I
D position switch
1 position switch 1 POSITION SW
[ONIOFF]
I
D POSITION SW
[ON/OFF] X
ASCD OD cut signal
ASCD.OD CUT
[ONIOFF]
X
ASCD cruise signal
Status of ASCD OD release
signal is displayed.
ON
... OD released
OFF ... OD not released
ONIOFF status, computed from
signal of
kickdown SW, is dis-
played.
ONIOFF status, computed from
signal of HOLD shift SW, is dis-
played.
ONIOFF status, computed from
signal of closed throttle position
SW, is displayed.
ONIOFF status, computed from
signal of wide open throttle
position SW, is displayed.
ASCD.CRUISE
[ONIOFF]
This
is displayed even when no
ASCD is mounted.
This is displayed even when no
kickdown switch is equipped.
Kickdown
switch
KICKDOWN
SW
[ONIOFq
Wide open throttle position switch X .
X A/T mode switch
t
WIO THRUP-SW
[ONIOFq POWERSHIFT SW
[ONIOFF]
Closed
throttle position switch
, CLOSED THUSW
[ONIOFF]

TROUBLE DIAGNOSES
Self-diagnosis
DESCRIPTION
If malfunction should occur in electrical systems, turning ignition switch ON lights M mode switch POWER
indicator lamp
(M-AT Dual matic AfT warning lamp) for 2 seconds, and then flashes the indicator lamp for 8 Gc
seconds. If malfunction does not occur, A/T mode switch POWER indicator lamp (M-AT Dual matic A/T warn-
ing lamp) is turned on for
2 seconds upon turning ignition switch ON. To locate and display the malfunction-
ing part, output the trouble information memory and flash
A/T mode switch POWER indicator lamp (M-AT Dual
matic
A/T warning lamp) by inputting self-diagnostic startup signal.
SELF-DIAGNOSIS PROCEDURE
1. Warm up engine.
2. Repeat ON-OFF cycles of ignition switch for more than once, and turn it OFF at last.
3. Move A/T mode switch to AUTO, and turn overdrive control switch to O/D ON.
4. Turn ignition switch ON with selector lever in "Pn position, and ensure POWER indicator lamp is turned on
for
2 seconds.
5. Turn ignition switch OFF.
6. Move selector lever to "D" position.
7. Turn overdrive control switch O/D OFF.
8. Turn ignition switch ON.
9. Move selector lever to "2" position.
10. Turn overdrive control switch OID ON.
11. Move selector lever to "I" position.
12. Turn overdrive control switch O/D OFF.
13. Depress accelerator pedal fully, and release it.
14. Read flashing status of POWER indicator lamp to complete self-diagnosis procedures.
M-AT
1. Warm up engine.
2. Repeat ON-OFF cycles of ignition switch for more than once, and turn it OFF at last.
3. Turn ignition switch ON with selector lever in "P" position, and ensure dual matic PJT warning lamp is turned
on for
2 seconds.
4. Turn ignition switch OFF.
5. Depress brake pedal, release accelerator pedal, and then move selector lever to "D" position.
6. Turn ignition switch ON.
7. Release brake pedal, and move selector lever to "3" position.
8. While depressing brake pedal with left foot, depress accelerator pedal fully with right foot, and move
selector lever to
"2" position.
9. Read dual matic A/T warning lamp indication to complete self-diagnosis procedures.

TROUBLE DIAGNOSES
Self-diagnosis (Cont'd)
\ I1 // \ 11 // =-I= or =mj= // 11 \ // 11 \
1, = 2.5 sec. t, = 2.0 sec. t, = 1.0 sec.
RB20DE 10 judgement flashes.
Stan signal Malfunctioning unit and circuit I
Except RBPODE 13 judgement flashes.
signal Malfunctioning unit and circuit I
POWER INDICATOR LAMP OR DUAL MATIC A/T
WARNING LAMP INDICATION
If malfunction occurs in electrical system, indicator lamp stays on
longer at corresponding circuit.
Flashing
order
t5 1 Overrun clutch solenoid
1
2
3
4
5
7 1 Lock-up solenoid
Malfunctioning
unit and circuit
Vehicle speed sensor
1
Vehicle speed sensor 2
Throttle position sensor
Shift solenoid
A
Shift solenoid B
I
W fluid temperature sensor, TCM power supply, or throttle posi-
tion sensor power supply
RB20DE
9 1 Engine speed
signal Except
RB20DE
10 1 Line
pressure solenoid I Turbine sensor
I - I Line pressure solenoid
12 1 - I Total control signal
When indicator lamp repeats flashing in 4 Hz, the following malfunctions
may exist: (Insufficient memory backup
powerflCM repiacement1Battery
has been disconnected for prolonged
periodllow battery power)
13
No flashes
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
To facilitate cause investigation of malfunction that is less likely to
reappear, the TCM always stores self-diagnostic results during cus-
tomer operation. This memory cannot be erased even if ignition
switch
is turned ON and OFF repeatedly. To erase the seif-diag-
nostic
results, turn ignition switch
OFF after self-diagnosis has
been performed, or use
"ERASE" function of CONSULT.
- - - - Shift control unit
PNP switch, idle
switch/full switch
Overdrive control switch Stop lamp switch

TROUBLE DIAGNOSES
Symptom Chart
Sharp shock in Engine brake
applied
Shifting
Malfunctions
Slip
(Racing)
hifting
.- erator pedal
Shifting
Shifting
inspection item
Fluid level and status
Control linkage
PNP switch (short/open circuit)
Throttle ~osition sensor (installed)
I Vehicle weed sensor
I Enaine meed sensor
A/T fluid temperature sensor
Engine idle speed
Line
Dressure
Control valve assembly
Shift solenoid
A
Shift solenoid B
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
Accumulator N-D
Accumulator
1-2
Accumulator 2-3
Accumulator 3-4 (N-R) Ignition coil and starter motor
Overdrive control switch
I AfT mode switch (AUTO)
Torque converter
1 Oil pump
I Reverse clutch
I High clutch
I Forward clutch
I Forward one-wav clutch
I Overrun ciutch
1 Low one-wav clutch
I Low reverse brake
Brake. band (including servo)
Parking linkage

Symptom Chart (Cont'd)
Greater noise
Malfunctions
Inspection item No shifting
I Shifting I
Fluid level
and status 11
Control linkage
-
(I) C 0 .- c. .- (I) 0 a
v
-CU
n - 1
PNP switch
(shortlopen
circuit)
Throttle position sensor (installed)
2 2
Vehicle speed sensor
I Engine speed sensor -
-T
L o 1 Control valve assembly .- - -- Shift solenoid A 4 3
. ' Shift solenoid 6 4 cut I1
--, Line pressure solenoid .- 5 -t Lock-up solenoid ?
6 Overrun clutch solenoid 3
Accumulator N-D
1 Accumulator 1-2 I 1-
Accumulator 2-3
Accumulator 3-4 (N-R)
Ignition coil and starter motor
I Overdrive control switch I 1-
A/T mode switch (AUTO)
A/T mode switch (POWER) I - I Ail mode switch (SNOW) I
I Torque converter I I
1 Oil pump I I -- - - Reverse clutch 0 -
'g High clutch a 4 6
%I Forward clutch I I - .- a Forward one-way clutch -
$ Overrun clutch a, 8
Low one-way clutch
O Low reverse brake 7
Brake band (including servo) 7
Parking linkage

TROUBLE DIAGNOSES
Symptom Chart (Cont'd)
xi - - ([I C V) a, C .- cn C W
t 0 .- .L 2 a, - 8 0 ([I L 0 0 Q
& 0 a, a, Q V)
5 E .- X
i! L a
zl -I - 1 -
- 2 -
-
-
-
-
-
5 - 3 - 4 -
-
-
-
-
-
-
-
-
-
-
-
-
I1 - 0 - 6 - 7 -
-
-
-
-
9 - 8 -
-
vj c 0 .- - .- V) 0 n
Q 7J C ([I
t C .- r ([I c. V) c. 0 C V) a 0 7J 0, C .- 0 C W -
- 2 - 3 -
-
- -
-
1 -
-
-
-
- - a +- ([I a a, 2 0 c. 0 C V) a, 0 u a, - 0 2
8 - 1 -
-
-
-
-
-
-
-
2 - 3 -
-
-
-
-
-
-
-
-
-
-
- I
i
g
- 4 -
-
-
-
-
-
-
B- ; 2 to a =? - 0,
2 5.j c 2.z 2 a0 - 0- z & 5 0 gE V) V)o C 02 .s nu 5 ng %-([I C O c --t .- V) a V) r aa ([I z gz a, a- c 50 -6 s
6 $2
11
2
I
I
Malfunctions
Inspection item
I I I Fluid level and status I I Control linkage 2
PNP switch (shortfopen circuit) 1 I I I Throttle position sensor (installed) 111213
Vehicle speed sensor
214
Engine speed sensor L -
AIT fluid temperature sensor
Engine idle weed
Line pressure
Control valve assembly
Shift solenoid A 3
3
Shift solenoid B 4 4
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
u I I I -
Accumulator N-D I I 1 I Accumulator 1-2
Accumulator 2-3 I Accumulator 3-4 (N-R)
Ignition coil and starter motor
Overdrive control switch
Torque converter
tg Reverse clutch .- High clutch
2 Forward clutch C .- a Forward one-way clutch -.
$ Overrun clutch 0, 8
? Low one-way clutch 3= O Low reverse brake 9
Brake band (including servo)
Parking linkage

ANTI-LOCK BRAKE SYSTEM
Component
Parts Location
Master
Front
Booster /'
ear wheel sensor
@ ABS control unit
right wheel sensor
Front left wheel
sens&
-/
a ABS actuator
Front right wheel sensor connector
.. .
!a In the instrument panel on
LH side of engine compartment dR/Y A