instrument panel NISSAN GT-R 2009 User Guide

Black plate (69,1)
Model "R35-D" EDITED: 2008/ 5/ 20
in this Owner’s Manual.
SUPPLEMENTAL AIR BAG WARN-
ING LABELSWarning labels about the supplemental front-
impact air bag and front seat-mounted side-
impact supplemental air bag systems are placed
in the vehicle as shown in the illustration.*1
SRS air bag
The warning labels are located on the surface of
the sun visors.*2
SRS side-impact air bag (if so
equipped)
The warning label is located on the side of the
passenger’s side center pillar.
SUPPLEMENTAL AIR BAG WARN-
ING LIGHTThe supplemental air bag warning light, display-
ing
in the instrument panel, monitors the
circuits of the supplemental front-impact air bag,
front seat-mounted side-impact supplemental
air bag (if so equipped) , roof-mounted curtain
side-impact supplemental air bag (if so
equipped) and seat belt pretensioner systems.
The monitored circuits include the Air bag
Control Unit (ACU) , satellite sensors, crash
zone sensor, front air bag modules, side air
bag modules (if so equipped) , curtain side-
impact air bag modules (if so equipped) ,
pretensioners and all related wiring.
Safety — Seats, seat belts and supplemental restraint system
1-43
,QIRUPDWLRQ3URYLGHGE\

Black plate (10,1)
2 Instruments and controls
Model "R35-D" EDITED: 2008/ 5/ 20
Cockpit............................................................ 2-2
Instrument panel ................................................ 2-3
Meters and gauges ............................................. 2-4
Speedometer ................................................ 2-5
Odometer/twin trip odometer ............................ 2-5
Tachometer ................................................... 2-6
Engine coolant temperature gauge ..................... 2-6
Fuel gauge ................................................... 2-7
Transmission position indicator .......................... 2-7
Upshift indicator ............................................. 2-8
Instrument brightness control .......................... 2-10
Vehicle information display .................................. 2-10
Engine oil level display .................................. 2-11
Transmission system check display ................... 2-12
Drive computer ................................................ 2-13
Current fuel consumption ............................... 2-14
Vehicle speed ............................................. 2-14
Cruise control ............................................. 2-14
Average fuel consumption and speed. ............... 2-15
Elapsed time and trip odometer ....................... 2-15
Distance to empty ........................................ 2-16
Outside air temperature ................................. 2-16
Setting (drive computer) ................................ 2-17
Warning (drive computer) ............................... 2-21
Warning/indicator lights and audible reminders ....... 2-23
Checking bulbs ........................................... 2-23 Warning lights
............................................. 2-23
Indicator lights ............................................. 2-28
Audible reminders ........................................ 2-30
Warning display ............................................... 2-31
Engine oil low pressure warning ...................... 2-32
Engine system warning .................................. 2-32
Shift lever position warning ............................. 2-32
Transmission system warning .......................... 2-33
Transmission oil high temperature warning ......... 2-33
Transmission clutch high temperature warning. .... 2-33
Parking brake release warning ......................... 2-34
Low brake fluid warning ................................. 2-34
Anti-lock Braking System (ABS) warning ........... 2-34
Vehicle Dynamic Control (VDC) system
warning ..................................................... 2-35
AWD clutch high temperature warning .............. 2-35
Front/rear tire size discrepancy warning ............. 2-35
AWD system warning .................................... 2-36
Low tire pressure warning .............................. 2-36
Run-flat tire warning ..................................... 2-36
Tire Pressure Monitoring System (TPMS) warning .................................................... 2-37
Cruise control system warning ........................ 2-37
Low fuel warning .......................................... 2-37
Door/trunk open warning. ............................... 2-38
Low washer fluid warning ............................... 2-38
,QIRUPDWLRQ3URYLGHGE\

Black plate (75,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Outside mirror control switch (P.3-27)
2. Center dial*
3. Audio system*
4. Heater and air conditioner*
5. Multi function display*
6. Hazard warning flasher switch (P.2-50)7. Glove box (P.2-55)
8. Fuse box cover (P.8-22)
9. Power outlet (P.2-52)
10. Rear window defroster switch (P.2-46)
11. CompactFlash card slot*
12. Front passenger air bag status light (P.1-37)13. Compact Disc slot*
14. Trunk release power cancel switch (P.3-20)
*: Refer to the separate Multi Function Display
Owner’s Manual.
Instruments and controls
2-3
INSTRUMENT PANEL
,QIRUPDWLRQ3URYLGHGE\

Black plate (116,1)
Model "R35-D" EDITED: 2008/ 5/ 20
FCC Rules and RSS-210 of Industry Cana-
da. Operation is subject to the following
two conditions;
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation of the device.
CHANGES OR MODIFICATIONS NOT EX-
PRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD
VOID THE USER’S AUTHORITY TO OPER-
ATE THE EQUIPMENT.
Security indicator lightThe security indicator light is located on the
instrument panel. It indicates the status of the
NISSAN Vehicle Immobilizer System.
The light blinks after the ignition switch was in
the LOCK position. This function indicates the
security systems equipped on the vehicle are
operational.
If the NISSAN Vehicle Immobilizer System is
malfunctioning, this light will remain on while the
ignition switch is in the ON position.
If the light still remains on and/or the
engine will not start, see a GT-R certified
NISSAN dealer for NISSAN Vehicle Immo-bilizer System service as soon as possible.
Please bring all Intelligent Keys that you
have when visiting a GT-R certified
NISSAN dealer for service.
2-44
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\

Black plate (130,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Automatic adjusting function
CAUTION
When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic win-
dow adjusting function will not work
and the side roof panel may be da-
maged.
The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to avoid
contact between the window and the side roof
panel. When the door is closed, the window is
automatically raised slightly.
While the automatic adjusting function does not
work, the window will be controlled as follows:
. When the door is opened, the window
lowers for approximately 2 seconds.
. While the door is open, the window cannot
be raised.If the windows do not close auto-
maticallyIf the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system. 1. Push the ignition switch to the ON position.
2. Close the door.
3. Open the window more than halfway by
operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.
5. Release the power window switch. Operate the window by the automatic function to
confirm the initialization is complete.
6. Perform steps 2 through 5 above for other windows.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked by a
GT-R certified NISSAN dealer.
MAP LIGHTSPush the button as illustrated to turn the light on
or off.
2-58
Instruments and controls
INTERIOR LIGHTS
,QIRUPDWLRQ3URYLGHGE\

Black plate (153,1)
Model "R35-D" EDITED: 2008/ 5/ 20
OPENING THE HOOD1. Pull the hood lock release handle
*1
located below the instrument panel. The
hood will then spring up slightly.
2. Pull the lever
*2
at the front of the hood
with your fingertips and raise the hood.
3. Grasp the insulated part of the stay
*3
and
release it from the hook, then securely insert
it into the hood hole
*4.
WARNING
If you see steam or smoke coming from
the engine compartment, do not open
the hood. Doing so could cause injury.
CAUTION
. Do not insert hands, clothing, tools
or other items into the engine
compartment while the engine is
running.Pre-driving checks and adjustments
3-17
HOOD
,QIRUPDWLRQ3URYLGHGE\

Black plate (178,1)
Model "R35-D" EDITED: 2008/ 5/ 20
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except
in an emergency. (The engine will stop
when the ignition switch is pushed
three consecutive times or the ignition
switch is pushed and held for more than
2 seconds.) If the engine stops while
the vehicle is being driven, this could
lead to a crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the shift lever to the&Pposition.
OPERATING RANGE FOR ENGINE
STARTThe operating range for starting the engine
inside the vehicle is shown in the illustration.
. If the Intelligent Key is on the instrument
panel, rear parcel shelf, inside the glove box
or door pocket, or the corner of interior
compartment, it may not be possible to start
the engine.
. If the Intelligent Key is near the door or door
glass outside the vehicle, it may be possible
to start the engine.
IGNITION SWITCH OPERATIONWhen the Intelligent Key is carried with you and
the ignition switch is pushed without depressing
the brake pedal, the ignition switch position will
change as follows:
.Push center once to change to ACC.
. Push center two times to change to ON.
. Push center three times to change to OFF.
(No position illuminates.)
. Push center four times to return to ACC.
. Open or close any door to return to LOCK
during the OFF position.
5-8
Starting and driving
PUSH-BUTTON IGNITION SWITCH
,QIRUPDWLRQ3URYLGHGE\

Black plate (189,1)
Model "R35-D" EDITED: 2008/ 5/ 20
GearMPH (km/h)
1st 35 (57)
2nd 62 (101)
3rd 90 (145)
4th —
5th —
6th —
DRIVING TIPSAfter starting the engine, fully depress the foot
brake pedal and push the shift lever button
before shifting the shift lever from the
&Pposition
to the
&R,&N,or
&A↔&M
position. Be sure the
vehicle is fully stopped before attempting to shift
the shift lever.
The transmission is designed so that the foot
brake pedal must be depressed before shifting
from
&Pto any other position.
The shift lever cannot be moved out of the
&P
position and into any other position with the
ignition switch other in the LOCK, OFF or ACC
position.When accelerating from a stopKeep the foot brake pedal depressed and push
the shift lever button to shift into a driving gear
as following:
. To drive forward, move the shift lever to the
&A↔&M
position.
. To back up, move the shift lever to the
&R
position.
Starting on level ground:1. Check the shift lever position indicator on
the instrument panel to confirm that the
driving gear is selected.
2. Release the parking brake.
3. Release the foot brake pedal, then gradually depress the accelerator pedal to start the
vehicle in motion.Starting on an uphill:1. Check the shift lever position indicator onthe instrument panel to confirm that the
driving gear is selected.NOTE:When starting or driving on a steep uphill
grade, shift to the
&M
position and operate
the paddle shifter to shift down to 1st gear
as a manual transmission vehicle.
2. With the parking brake applied, slowly release the foot brake pedal.
3. Slowly depress the accelerator pedal and feel the vehicle starting motion with the
parking brake applied.
4. Release the parking brake and gradually depress the accelerator pedal to start the
vehicle in motion.
NOTICE
To prevent stalling or transmission
damage, start in 1st gear. The
&M
position 2nd gear can be used to start
moving the vehicle only when reduced
torque is necessary on snowy roads or
extremely slippery surfaces.NOTE:The hill start assist function operates when
the vehicle is accelerating from a stop on
an uphill. (
“HILL START ASSIST” page
5-31)
When driving the vehicle
WARNING
Do not move the shift lever to the
&N
position while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage the
transmission.
Starting and driving
5-19
,QIRUPDWLRQ3URYLGHGE\

Black plate (191,1)
Model "R35-D" EDITED: 2008/ 5/ 20
serious injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.When parking the vehicle1. Bring the vehicle to a complete stop.
2. With the foot brake pedal depressed, applythe parking brake.
3. Move the shift lever to the
&Pposition.
4. Check the shift lever position indicator on the instrument panel to confirm that the
&P
position is selected.
5. Push the ignition switch to stop the engine.
WARNING
Before exiting the vehicle, be sure to
move the shift lever to the
&Pposition
and stop the engine. If the engine is
running and the shift lever is not in the
&Pposition, the vehicle may start mov-
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly caus-
ing an accident.
The control of the dual clutch transmission,
Bilstein DampTronic
®electronically controlled
shock absorbers and Vehicle Dynamic Control
(VDC) can be changed to the desired modes by
operating the setup switches. Select the desired
mode best suited to the driving conditions.
NOTE:Bilstein DampTronic
®is a registered trade-
mark of ThyssenKrupp Bilstein Suspen-
sion GmbH.
Starting and driving
5-21
VDC, TRANSMISSION AND
SUSPENSION SETUP SWITCHES
,QIRUPDWLRQ3URYLGHGE\

Black plate (200,1)
Model "R35-D" EDITED: 2008/ 5/ 20
2. Accelerate your vehicle to the desiredspeed, push the SET/COAST switch and
release it. (The SET indicator will illuminate
in the instrument panel.) Take your foot off
the accelerator pedal. Your vehicle will
maintain the set speed.NOTE:If the vehicle speed reaches approximately
3 MPH (5 km/h) over the set speed, the set
speed on the vehicle information display
blinks.
Passing another vehicleTo pass another vehicle, depress the accelerator
pedal. When you release the pedal, the vehicle
will return to the previously set speed.Increasing the set vehicle speedTo reset at a faster cruising speed, use one of
the following methods:
.Depress the accelerator pedal. When the
vehicle attains the desired speed, push and
release the SET/COAST switch.
. Push and hold the RESUME/ACCELERATE
switch. When the vehicle attains the speed
you desire, release the switch.
. Push and then quickly release the RESUME/
ACCELERATE switch. Each time you do
this, the set speed will increase by about 1
MPH (1.6 km/h) .Decreasing the set vehicle speedTo reset at a slower cruising speed, use one of
the following methods:
.Lightly tap the brake pedal. When the
vehicle attains the desired speed, push
and release the SET/COAST switch.
. Push and hold the SET/COAST switch.
Release the switch when the vehicle slows
down to the desired speed.
. Push and then quickly release the SET/ COAST switch. Each time you do this, the
set speed will decrease by about 1 MPH
(1.6 km/h) .
Resuming the preset speedTo resume the preset speed, push and release
the RESUME/ACCELERATE switch. The vehicle
will resume the last set cruising speed when the
vehicle speed is over 25 MPH (40 km/h) .
5-30
Starting and driving
,QIRUPDWLRQ3URYLGHGE\