engine NISSAN GT-R 2009 Owner's Manual

Black plate (81,1)
Model "R35-D" EDITED: 2008/ 5/ 20
SettingPush the ignition switch to the ON position. Use
the ENTER switch
and toggle the vehicle
information display to show the SETTING
screen.
Use the NEXT switch
and ENTER switch
to go to ALERT > UPSHIFT. The current
status of the upshift indicator will be shown on
the UPSHIFT screen. Note that the function is
set to AUTO as the factory default setting.
To change the upshift indicator mode, choose
SETTING on the UPSHIFT screen. Set one of
the following modes by pushing the NEXT
switch
, and then push ENTER
to
complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push and
hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:Set the upshift indicator to AUTO. The yellow
indicator illuminates approximately 700 RPM
before the red zone, and the red indicator illuminates just before the red zone.
When the maximum engine torque is
desired:Set the figure at 5,200 RPM. The green
indicator starts flashing from approximately
4,700 RPM and illuminates at 5,200 RPM.When breaking-in the vehicle:To help avoid high engine speeds during break-
in, set the upshift indicator to less than 3,500
RPM. The green indicator starts flashing ap-
proximately 500 RPM before the set figure and
illuminates from the set figure. (
“BREAK-IN
SCHEDULE” page 5-32)
NOTE:. There may be a slight difference be-
tween the timing of the upshift indica-
tor illumination and the tachometer
indication.
. When the battery terminal is discon-
nected, the set memory will be erased
and the mode returns to the default.
Instruments and controls
2-9
,QIRUPDWLRQ3URYLGHGE\

Black plate (82,1)
Model "R35-D" EDITED: 2008/ 5/ 20
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be adjusted
when the ignition switch is in the ON position.
Press the switch to adjust the brightness up
*1
or down
*2. The brightness level is shown on
the vehicle information display.
When the headlights are on, the brightness of
the interior switches is also adjusted at the same
time.
NOTE:. The instrument brightness can be ad-
justed separately for daytime and
nighttime conditions. The adjusted set- tings are automatically stored.
. When the battery terminal is discon-
nected, the set memory will be erased
and the setting returns to the default.
The vehicle information display can display the
following information.
.Engine oil level display
. Transmission system check display
. Instrument brightness control level display
(
“INSTRUMENT BRIGHTNESS CON-
TROL” page 2-10)
. Drive computer
(“DRIVE COMPUTER” page 2-13)
. Warning display
(“WARNING DISPLAY” page 2-31)
. Operation display
(“OPERATION DISPLAYS” page 2-
39)
. Cruise control display
(“CRUISE CONTROL” page 5-28)
2-10
Instruments and controls
VEHICLE INFORMATION DISPLAY
,QIRUPDWLRQ3URYLGHGE\

Black plate (83,1)
Model "R35-D" EDITED: 2008/ 5/ 20
ENGINE OIL LEVEL DISPLAYWhen the ignition switch is pushed to the ON
position, the engine oil status before starting the
engine is indicated as illustrated.When the oil level is normal“OIL LEVEL OK” is displayed. Press the
displayed LEVEL switch
to check the oil
level.
NOTE:The engine oil level can be displayed after
the “OIL LEVEL OK” display turns off or
while the engine is started and running.
(
“Maintenance” page 2-19)
When the oil level is lowIf the message shown above is displayed, the
engine oil level is low.
Warm up the engine in a level location. After at
least 5 minutes have passed since engine stop,
use the engine oil level gauge to check the oil
level. (
“ENGINE OIL” page 8-12)
If the oil level is low, have additional engine oil
added, or the oil changed, at a GT-R certified
NISSAN dealer.Instruments and controls
2-11
,QIRUPDWLRQ3URYLGHGE\

Black plate (84,1)
Model "R35-D" EDITED: 2008/ 5/ 20
NOTICE
If the vehicle is in a location that is not
level, accurate measurement of the oil
level may not be possible. If “LOW OIL
LEVEL” is displayed, but the level
shown by the oil level gauge is normal,
move the vehicle to a level location and
stop the engine. After at least 5 minutes
have passed, open the driver’s door and
push the ignition switch back to ON. If
the “LOW OIL LEVEL” message appears
again, have engine oil added or the oil
changed.
When the oil level sensor malfunc-
tion occursIf the message shown above is displayed, the
engine oil level sensor may be malfunctioning.
Contact a GT-R certified NISSAN dealer im-
mediately.
TRANSMISSION SYSTEM CHECK
DISPLAYThis is displayed after the engine is started while
the transmission system is being checked. It
turns off after a few seconds.NOTE:.During the system check, the shift lever
cannot be moved out of the
&Pposition.
Operate the shift lever after the system
check indicator turns off.
. During winter or at other times when
the temperature is extremely low,
changes in the hydraulic response
characteristics may increase the
2-12
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\

Black plate (85,1)
Model "R35-D" EDITED: 2008/ 5/ 20
amount of time that is required for the
system check. During the system check,
a thudding operating noise may occur
or the engine speed may decrease,
however this does not indicate that
there is a malfunction.
1. ENTER switch2. NEXT switch3. Vehicle information displayThe drive computer displays the following
information:
.Current fuel consumption
. Vehicle speed
. Cruise control
. Average fuel consumption and speed
. Elapsed time and trip computer
. Distance to empty
. Outside air temperature .
Setting
. Warning
The vehicle information display
*3
can be
changed when the ignition switch is in the ON
position. Press the ENTER switch*1
to
change the display.
NOTE:. The cruise control display is shown if
cruise control is set. (
“CRUISE
CONTROL” page 5-28)
. The warning display is not shown if
there are no conditions to warn the
driver.
. Depending on the driving conditions
and other factors, the displayed values
may differ from the actual values.
. The position of the speedometer nee-
dle and the speed shown in the vehicle
information display may slightly differ.
Instruments and controls
2-13
DRIVE COMPUTER
,QIRUPDWLRQ3URYLGHGE\

Black plate (88,1)
Model "R35-D" EDITED: 2008/ 5/ 20
DISTANCE TO EMPTYThis displays the approximate distance that the
vehicle can be driven based on the amount of
fuel remaining in the fuel tank and the actual fuel
consumption.NOTE:.If the fuel level is low, the low fuel
warning will be displayed. (
“LOW
FUEL WARNING” page 2-37)
. If the vehicle is not refueled after the
low fuel warning appears, the display
will change to “
”. This change
timing may become earlier depending
on the driving conditions. This does not indicate that there is a malfunction.
. The values are updated approximately
every 30 seconds.
OUTSIDE AIR TEMPERATUREThis displays the outside air temperature.NOTE:.The outside air temperature may not be
displayed correctly in the following
cases.
— The outside air temperature is low-
er than 22 8F( 30 8C) or is higher
than 131 8F (55 8C) .
— The vehicle is stopped or is driving at a low speed (less than approxi-
mately 12 MPH (20 km/h)) .
— The temperature in the engine compartment is high.
2-16
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\

Black plate (91,1)
Model "R35-D" EDITED: 2008/ 5/ 20
MaintenanceThis function can be used to set the various
maintenance intervals and to check the engine
oil level. The reminders shown below are used to
notify the driver of the maintenance intervals.NOTE:Because these are displayed based on the
mileage driven, they do not indicate the
actual conditions of the vehicle. Use these
functions only as a reference.
Input the maintenance distance using the
following items:
.On each setting screen, push the NEXT
switch
to change the mileage. Push and hold the switch to increase the number
every 600 miles (1,000 km) .
. Set to “—” to set no reminders.
. To reset the accumulated mileage to zero,
go to the RESET screen, then push the
NEXT switch
and confirm with the
ENTER switch.
NOTE:. To restore the mileage to the original
figure after resetting, press the NEXT
switch
again.
. When the battery terminal is discon-
nected, the set mileage will be erased
and the settings will return to their
default settings.
Engine oil level:This can be used to check the pre-start oil level
while the engine is running. Select SETTING >
MAINTENANCE > OIL > ENGINE OIL >
LEVEL.
If the low level reminder appears, check the level
using the engine oil dipstick. (
“CHECKING
ENGINE OIL LEVEL” page 8-12)
Instruments and controls
2-19
,QIRUPDWLRQ3URYLGHGE\

Black plate (92,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Engine oil:When the set mileage approaches, the reminder
will appear on the display and the remaining
distance is displayed at regular intervals. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL to set or reset the mileage for the engine oil
change.NOTE:The default setting is 6,000 miles (10,000
km) . The maximum mileage that can be set
is 6,000 miles (10,000 km) .
Engine oil filter:The reminder is displayed when the set mileage
is exceeded. Select SETTING > MAINTE-
NANCE > FILTER to set or reset the mileage
for the engine oil filter change.NOTE:The default setting is OFF. The maximum
mileage that can be set is 6,000 miles
(10,000 km) .
Transmission oil:The reminder is displayed when the set mileage
is exceeded. Select SETTING > MAINTE-
NANCE > OIL > T/M OIL to set or reset the
mileage for the transmission oil change.NOTE:The default setting is 18,500 miles (30,000
km) . The maximum mileage that can be set
is 18,500 miles (30,000 km) .
2-20
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\

Black plate (95,1)
Model "R35-D" EDITED: 2008/ 5/ 20
All-Wheel Drive (AWD) warning light
Intelligent Key warning light
Cruise set switch indicator light
Anti-lock Braking System (ABS) warning
light
Low tire pressure warning light
Front passenger air bag status light
Master warning light
High beam indicator light (blue)
Brake warning light
Seat belt warning light
Malfunction Indicator Light (MIL)
Supplemental air bag warning light
Slip indicator light
Charge warning light
Transmission warning light
Turn signal/hazard indicator lights
Engine oil pressure warning light
Cruise main switch indicator light
Vehicle Dynamic Control (VDC) off indicator
light
CHECKING BULBSWith all doors closed, apply the parking brake
and push the ignition switch to the ON position
without starting the engine. The following lights
will come on:
,
or
,
,
,
,
,
The following lights come on briefly and then go
off:
,
or
,
,
,
,
,
If any light does not come on, it may indicate aburned-out bulb or an open circuit in the
electrical system. Have the system checked by
a GT-R certified NISSAN dealer.
WARNING LIGHTS
All-Wheel Drive (AWD) warn-
ing light
The
warning light comes on when the
ignition switch is pushed to ON. It turns off soon
after the engine is started.
If the AWD system malfunctions, the warning
light will either remain illuminated or blink.
(
“ALL-WHEEL DRIVE (AWD)” page 5-34)
CAUTION
. If the warning light comes on while
driving there may be a malfunction
in the AWD system. Reduce the
vehicle speed and have your vehicle
checked by a GT-R certified NISSAN
dealer as soon as possible.
. If the AWD warning light blinks on
when you are driving:
— blinks rapidly (about twice a
second):
Instruments and controls
2-23
WARNING/INDICATOR LIGHTS AND
AUDIBLE REMINDERS
,QIRUPDWLRQ3URYLGHGE\

Black plate (96,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Pull off the road in a safe area,
and idle the engine. The driving
mode will change to RWD to
prevent the AWD system from
malfunctioning. If the warning
light turns off, you can drive
again.
— blinks slowly (about once every 2 seconds):
Pull off the road in a safe area,
and idle the engine. Check that
all tire sizes are the same as
that specified on the Tire and
Loading Information label lo-
cated in the driver’s door open-
ing, tire pressure is correct and
tires are not worn. (
“TIRE
AND LOADING INFORMATION
LABEL” page 9-10)
If the tire pressure is insuffi-
cient, fill with nitrogen gas.
Contact a GT-R certified NISSAN
dealer about filling with nitro-
gen gas. If nitrogen gas is not
available, compressed air may
be safely used under normal
driving conditions. However,
NISSAN recommends refilling
with nitrogen gas for maximum tire performance.
. If the warning light is still on after
the above operations, have your
vehicle checked by a GT-R certified
NISSAN dealer as soon as possible.
or
Anti-lock Braking
System (ABS) warn-
ing light
When the ignition switch is in the ON position,
the Anti-lock Braking System (ABS) warning
light illuminates and then turns off. This indicates
the ABS is operational.
If the ABS warning light illuminates while the
engine is running, or while driving, it may
indicate the ABS is not functioning properly.
Have the system checked by a GT-R certified
NISSAN dealer.
If an ABS malfunction occurs, the anti-lock
function is turned off. The brake system then
operates normally, but without anti-lock assis-
tance. (
“BRAKE SYSTEM” page 5-38)
or
Brake warning light
This light functions for both the parking brake
and the foot brake systems.
Parking brake indicator:When the ignition switch is in the ON position,
the light comes on when the parking brake is
applied.Low brake fluid warning light:When the ignition switch is in the ON position,
the light warns of a low brake fluid level. If the
light comes on while the engine is running with
the parking brake not applied, stop the vehicle
and perform the following:
1. Check the brake fluid level. Add brake fluid
as necessary. (
“BRAKE FLUID” page
8-14)
2. If the brake fluid level is correct, have the warning system checked by a GT-R certified
NISSAN dealer.
Anti-lock Braking System (ABS) warning
indicator:When the parking brake is released and the
brake fluid level is sufficient, if both the brake
warning light and the Anti-lock Braking System
(ABS) warning light illuminate, it may indicate
the ABS is not functioning properly. Have the
brake system checked, and if necessary re-
paired, by a GT-R certified NISSAN dealer
promptly. Avoid high-speed driving and abrupt
braking. (
“Anti-lock Braking System (ABS)
warning light” page 2-24)
2-24
Instruments and controls
,QIRUPDWLRQ3URYLGHGE\