engine NISSAN GT-R 2009 Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2009, Model line: GT-R, Model: NISSAN GT-R 2009Pages: 311, PDF Size: 6.68 MB
Page 175 of 311
Black plate (19,1)
5 Starting and driving
Model "R35-D" EDITED: 2008/ 5/ 20
Precautions when starting and driving..................... 5-2
Exhaust gas (Carbon monoxide) ........................ 5-2
Three-way catalyst .......................................... 5-2
Tire Pressure Monitoring System (TPMS) ............. 5-3
Avoiding collision and rollover ........................... 5-5
Off-road recovery ........................................... 5-6
Rapid air pressure loss .................................... 5-6
Drinking alcohol/drugs and driving ...................... 5-7
All-Wheel Drive (AWD) driving safety
precautions ................................................... 5-7
Push-button ignition switch .................................. 5-8
Operating range for engine start ........................ 5-8
Ignition switch operation .................................. 5-8
Ignition switch positions ................................... 5-9
Intelligent Key battery discharge ...................... 5-10
Before starting the engine .................................. 5-11
Starting the engine ........................................... 5-11
Driving the vehicle ............................................ 5-13
Dual clutch transmission ................................ 5-13
Driving tips ................................................. 5-19
VDC, transmission and suspension setup
switches ........................................................ 5-21
How to switch the modes .............................. 5-22
Features of each mode .................................. 5-23
Turbocharger system ......................................... 5-26
Parking brake .................................................. 5-27 Cruise control
................................................. 5-28
Precautions on cruise control .......................... 5-28
Steering-wheel-mounted controls ..................... 5-29
Indicators and display ................................... 5-29
Cruise control operations ............................... 5-29
Hill Start Assist ................................................ 5-31
Break-in schedule ............................................ 5-32
Increasing fuel economy .................................... 5-33
All-Wheel Drive (AWD) ..................................... 5-34
AWD warning light ....................................... 5-34
Tight corner braking phenomenon .................... 5-35
Tires ......................................................... 5-35
AWD system characteristics ........................... 5-35
Limited Slip Differential (LSD) ............................. 5-36
Parking/parking on hills ...................................... 5-37
Power steering ................................................ 5-38
Brake system .................................................. 5-38
Braking precautions ...................................... 5-38
Parking brake break-in ................................... 5-39
Brake assist .................................................... 5-39
Anti-lock Braking System (ABS) ...................... 5-39
Vehicle Dynamic Control (VDC) system ................. 5-40
Cold weather driving ......................................... 5-42
Freeing a frozen door lock .............................. 5-42
Anti-freeze .................................................. 5-42
Battery ...................................................... 5-42
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 176 of 311
Black plate (20,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Draining of coolant water............................... 5-42
Tire equipment ............................................ 5-42
Special winter equipment ............................... 5-42 Driving on snow or ice
.................................. 5-42
Engine block heater (if so equipped) ................. 5-43
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 177 of 311
Black plate (172,1)
Model "R35-D" EDITED: 2008/ 5/ 20
WARNING
.Do not leave children or adults who
would normally require the support
of others alone in your vehicle. Pets
should not be left alone either. They
could accidentally injure themselves
or others through inadvertent op-
eration of the vehicle. Also, on hot,
sunny days, temperatures in a
closed vehicle could quickly become
high enough to cause severe or
possibly fatal injuries to people or
animals.
. Closely supervise children when
they are around cars to prevent
them from playing and becoming
locked in the trunk where they could
be seriously injured. Keep the car
locked, with the rear seatback and
trunk lid securely latched when not
in use, and prevent children’s access
to car keys.
EXHAUST GAS (Carbon monoxide)
WARNING
.Do not breathe exhaust gases; they
contain colorless and odorless car-
bon monoxide. Carbon monoxide is
dangerous. It can cause uncon-
sciousness or death.
. If you suspect that exhaust fumes
are entering the vehicle, drive with
all windows fully open, and have the
vehicle inspected immediately.
. Do not run the engine in closed
spaces such as a garage.
. Do not park the vehicle with the
engine running for any extended
length of time.
. Keep the trunk lid closed while
driving, otherwise exhaust gases
could be drawn into the passenger
compartment. If you must drive with
the trunk lid open, follow these
precautions:
1) Open all the windows.
2) Set the
air recirculation to
off and the fan control to high to
circulate the air. .
The exhaust system and body
should be inspected by a qualified
mechanic whenever:
— The vehicle is raised for service.
— You suspect that exhaust fumes
are entering into the passenger
compartment.
— You notice a change in the sound of the exhaust system.
— You have had an accident invol- ving damage to the exhaust
system, underbody, or rear of
the vehicle.
THREE-WAY CATALYSTThe three-way catalyst is an emission control
device installed in the exhaust system. Exhaust
gases in the three-way catalyst are burned at
high temperatures to help reduce pollutants.
WARNING
. The exhaust gas and the exhaust
system are very hot. Keep people,
animals or flammable materials
away from the exhaust system com-
ponents.
. Do not stop or park the vehicle over
flammable materials such as dry
5-2
Starting and driving
PRECAUTIONS WHEN STARTING
AND DRIVING
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 178 of 311
Black plate (173,1)
Model "R35-D" EDITED: 2008/ 5/ 20
grass, waste paper or rags. They
may ignite and cause a fire.
NOTICE
.Do not use leaded gasoline. Depos-
its from leaded gasoline seriously
reduce the three-way catalyst’s abil-
ity to help reduce exhaust pollu-
tants.
. Keep your engine tuned up. Mal-
functions in the ignition, fuel injec-
tion, or electrical systems can cause
overrich fuel flow into the three-way
catalyst, causing it to overheat. Do
not keep driving if the engine mis-
fires, or if noticeable loss of perfor-
mance or other unusual operating
conditions are detected. Have the
vehicle inspected promptly by a
GT-R certified NISSAN dealer.
. Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, dama-
ging the three-way catalyst.
. Do not race the engine while warm-
ing it up.
. Do not push or tow your vehicle to start the engine.
TIRE PRESSURE MONITORING
SYSTEM (TPMS)Each tire should be checked monthly when cold
and inflated to the inflation pressure recom-
mended by the vehicle manufacturer on the
vehicle placard or tire inflation pressure label. (If
your vehicle has tires of a different size than the
size indicated on the vehicle placard or tire
inflation pressure label, you should determine
the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a Tire Pressure Monitoring
System (TPMS) that illuminates a low tire
pressure telltale when one or more of your tires
is significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated tire
causes the tire to overheat and can lead to tire
failure. Under-inflation also reduces fuel effi-
ciency and tire tread life, and may affect the
vehicle’s handling and stopping ability.
If the vehicle is being driven with one or more flat
tires, the run-flat tire warning light will illuminate
continuously and a chime will sound for 10
seconds. The chime will only sound at the first
indication of a flat tire, and the warning light willilluminate continuously. When the Flat tire
warning is activated, have the system reset
and the tire checked and replaced if necessary
by a GT-R certified NISSAN dealer. Even if the
tire is inflated to the specified COLD tire
pressure, the warning light will continue to
illuminate until the system is reset by a GT-R
certified NISSAN dealer. Your vehicle can be
driven for a limited time on a flat tire. (
“Run-
flat tires” page 8-35)
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver’s
responsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when the
system is not operating properly. The TPMS
malfunction indicator is combined with the low
tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi-
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the
malfunction exists. When the malfunction indi-
cator is illuminated, the system may not be able
to detect or signal low tire pressure as intended.
TPMS malfunctions may occur for a variety of
reasons, including the installation of replace-
ment or alternate tires or wheels on the vehicle
Starting and driving
5-3
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 182 of 311
Black plate (177,1)
Model "R35-D" EDITED: 2008/ 5/ 20
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of
alcohol or drugs. Alcohol in the blood-
stream reduces coordination, delays
reaction time and impairs judgement.
Driving after drinking alcohol increases
the likelihood of being involved in an
accident injuring yourself and others.
Additionally, if you are injured in an
accident, alcohol can increase the se-
verity of the injury.
NISSAN is committed to safe driving. However,
you must choose not to drive under the influence
of alcohol. Every year thousands of people are
injured or killed in alcohol-related accidents.
Although the local laws vary on what is
considered to be legally intoxicated, the fact is
that alcohol affects all people differently and
most people underestimate the effects of
alcohol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs) . Don’t drive if
your ability to operate your vehicle is impaired by
alcohol, drugs, or some other physical condition.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS
WARNING
. Do not drive beyond the perfor-
mance capability of the tires, even
with AWD engaged. Accelerating
quickly, sharp steering maneuvers
or sudden braking may cause loss
of control.
. Always use the specified tires on all
four wheels. Install tire chains on
the rear wheels when driving on
slippery roads and drive carefully.
. This vehicle is not designed for
offroad (rough road) use. Do not
drive on sandy or muddy roads that
tires may get stuck in.
. Do not attempt to raise two wheels
off the ground and shift the trans-
mission to any
&A↔&Mor
&Rposition
with the engine running. Doing so
may result in drivetrain damage or
unexpected vehicle movement
which could result in serious vehicle
damage or personal injury.
. Do not attempt to test an AWD
equipped vehicle on a 2-wheel dy- namometer, (such as the dynam-
ometers used by some states for
emissions testing) , or similar equip-
ment even if the other two wheels
are raised off the ground. Make sure
you inform test facility personnel
that your vehicle is equipped with
AWDbeforeitisplacedona
dynamometer. Using the wrong test
equipment may result in drivetrain
damage or unexpected vehicle
movement which could result in
serious vehicle damage or personal
injury.
. When a wheel is off the ground due
to an unlevel surface, do not spin
the wheel excessively.
Starting and driving
5-7
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 183 of 311
Black plate (178,1)
Model "R35-D" EDITED: 2008/ 5/ 20
WARNING
Do not operate the push-button ignition
switch while driving the vehicle except
in an emergency. (The engine will stop
when the ignition switch is pushed
three consecutive times or the ignition
switch is pushed and held for more than
2 seconds.) If the engine stops while
the vehicle is being driven, this could
lead to a crash and serious injury.
Before operating the push-button ignition
switch, be sure to move the shift lever to the&Pposition.
OPERATING RANGE FOR ENGINE
STARTThe operating range for starting the engine
inside the vehicle is shown in the illustration.
. If the Intelligent Key is on the instrument
panel, rear parcel shelf, inside the glove box
or door pocket, or the corner of interior
compartment, it may not be possible to start
the engine.
. If the Intelligent Key is near the door or door
glass outside the vehicle, it may be possible
to start the engine.
IGNITION SWITCH OPERATIONWhen the Intelligent Key is carried with you and
the ignition switch is pushed without depressing
the brake pedal, the ignition switch position will
change as follows:
.Push center once to change to ACC.
. Push center two times to change to ON.
. Push center three times to change to OFF.
(No position illuminates.)
. Push center four times to return to ACC.
. Open or close any door to return to LOCK
during the OFF position.
5-8
Starting and driving
PUSH-BUTTON IGNITION SWITCH
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 184 of 311
Black plate (179,1)
Model "R35-D" EDITED: 2008/ 5/ 20
IGNITION SWITCH POSITIONS
LOCK (Normal parking position)The ignition switch can only be locked in this
position.
The ignition switch will be unlocked when it is
pushed to the ACC position while carrying the
Intelligent Key or with the Intelligent Key inserted
in the port.ACC (Accessories)This position activates electrical accessories
such as the radio, when the engine is not
running.ON (Normal operating position)This position turns on the ignition system and
electrical accessories.OFFThe engine can be turned off without locking the
steering wheel.
The ignition lock is designed so that the ignition
switch cannot be switched to the LOCK position
until the shift lever is moved to the
&Pposition.
NOTE:.If the steering lock release malfunction
indicator appears on the vehicle infor-
mation display when the ignition
switch is pressed, press the ignition
switch again while gently turning the steering wheel left and right.
(
“STEERING LOCK RELEASE
MALFUNCTION INDICATOR” page 2-
41)
. If the shift
&Pwarning appears on the
vehicle information display when the
ignition switch is pushed, the shift lever
is in any position except the
&P
posi-
tion. Move the shift lever to the&P
position. (
“SHIFT “P” WARNING”
page 2-40)
. If the Intelligent Key battery discharge
indicator appears on the vehicle infor-
mation display, the Intelligent Key
battery is discharged and the ignition
switch will not operate. Insert the
Intelligent Key into the key port to
operate the ignition switch.
(
“INTELLIGENT KEY BATTERY
DISCHARGE INDICATOR” page 2-42)
. When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
— The ignition switch is in the ACC
position, and
— All doors are closed, and
— The shift lever is in the
&Pposition. .
Do not leave the vehicle with the
ignition switch in the ACC or ON
position when the engine is not run-
ning for an extended period of time.
This can discharge the battery.
Starting and driving
5-9
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 185 of 311
Black plate (180,1)
Model "R35-D" EDITED: 2008/ 5/ 20
INTELLIGENT KEY BATTERY DIS-
CHARGEIf the battery of the Intelligent Key is almost
discharged, the guide light
*1
of the Intelligent
Key port blinks and the indicator appears on the
vehicle information display.
(
“INTELLIGENT KEY INSERTION INDI-
CATOR” page 2-41)
In this case, inserting the Intelligent Key into the
port allows you to start the engine. Make sure
that the mechanical key side faces backward as
illustrated. Insert the Intelligent Key in the port
until it is latched and secured.
To remove the Intelligent Key from the port, push
the ignition switch to the OFF position and pull the Intelligent Key out of the port.
NOTICE
Never place anything except the Intelli-
gent Key in the Intelligent Key port.
Doing so may cause damage to the
equipment.
NOTE:.
Make sure the Intelligent Key is in the
correct direction when inserting it into
the Intelligent Key port. The engine
may not start if it is in the incorrect
direction.
. Remove the Intelligent Key from the
Intelligent Key port after the ignition
switch is pushed to the OFF position.
5-10
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 186 of 311
Black plate (181,1)
Model "R35-D" EDITED: 2008/ 5/ 20
.The Intelligent Key port does not
charge the Intelligent Key battery. If
you see the low battery indicator in the
vehicle information display, replace the
battery as soon as possible.
(
“INTELLIGENT KEY BATTERY RE-
PLACEMENT” page 8-23)
. Make sure the area around the vehicle is
clear.
. Check fluid levels such as engine oil, cool-
ant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
. Check that all windows and lights are clean.
. Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
. Lock all doors.
. Position seat and adjust head restraints.
. Adjust inside and outside mirrors.
. Fasten seat belts and ask all passengers to
do likewise.
. Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (
“WARNING/INDICATOR
LIGHTS AND AUDIBLE REMINDERS”
page 2-23)
NOTE:. This vehicle includes spark plugs that
are designed for maximum perfor-
mance. If the start time becomes long-
er, the plugs may be fouled, making the
engine difficult to start. If this occurs,
start the engine using the procedure
described in this section.
. A click sound may be heard when the
brake pedal is depressed and released.
This is normal.
. A low rattling operating sound may
occur when the engine is started or
stopped. This does not indicate that
there is a malfunction. This sound is
likely to occur in particular if the engine
is stopped when the temperature of the
transmission oil is high.
Starting and driving
5-11
BEFORE STARTING THE ENGINE STARTING THE ENGINE
, Q I R U P D W L R Q 3 U R Y L G H G E \
Page 187 of 311
Black plate (182,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Check the positions of the accelerator pedal
*1
and brake pedal
*2. Adjust the steering
wheel and seat positions so that the correct
driving posture is achieved. (
“FRONT
SEATS” page 1-2)
2. Check that the parking brake is engaged.
3. Check that the shift lever is in the&Por&N
position. (
&Pis recommended.)
4. Firmly depress the brake pedal. Without depressing the accelerator pedal, press the
ignition switch once to start the engine.
5. To stop the engine, move the shift lever to the
&Pposition, and push the ignition switch
to the OFF position.
NOTE:. If the engine is difficult to start, de-
press the accelerator pedal all the way
to the floor and hold it. Push the
ignition switch with the brake pedal
depressed to start cranking the engine.
After 5 or 6 seconds, stop cranking by
pushing the ignition switch to the OFF
position, and then release the accel-
erator pedal. Then perform steps 1 to 4
to start the engine. If the engine starts,
but fails to run, repeat this procedure.
. Starting and stopping the engine over a
short period of time may make the
vehicle more difficult to start. If this
occurs, wait for more than 3 minutes,
and then press the ignition switch
again to start the engine.
. To maintain high performance over a
long period of time, the engine speed is
limited to 5,000 rpm when the engine is
revved with the shift lever in the
&Nor
&Pposition, and to 4,000 rpm when the
engine oil or coolant temperature is
low or higher than normal.
. If the ignition switch is pressed before
the shift lever is moved to the
&P
position, the ignition switch will not
change to the OFF position. If this occurs, the SHIFT
&P
warning display
appears on the vehicle information
display. When stopping the engine, be
sure to move the shift lever to the
&P
position and then press the ignition
switch. Failure to do so may result in
discharge of the battery. (
“SHIFT
“P” WARNING” page 2-40)
. If the shift lever was in the
&A↔&Mor
&R
position when the engine was stopped,
then be sure to move the shift lever to
the
&P
position before starting the
engine the next time. If the engine is
started with the shift lever in the
&N
position, then it may not be possible to
drive the vehicle even when the shift
lever is moved to the
&A↔&M
or
&R
position. If this occurs, the SHIFT
&P
warning appears on the vehicle infor-
mation display. (
“SHIFT “P”
WARNING” page 2-40)
CAUTION
If the engine was stopped soon when
the engine is hot, the cooling fan may
operate for approximately 2 minutes
after the engine was stopped to cool
the components in the engine compart-
5-12
Starting and driving
, Q I R U P D W L R Q 3 U R Y L G H G E \