clock NISSAN GT-R 2009 Owners Manual

Black plate (142,1)
Model "R35-D" EDITED: 2008/ 5/ 20
To activate or deactivate the automatic door lock
system, perform the following procedure:
1. Close all doors.
2. Push the ignition switch to the ON position.
3. Within 20 seconds, push and hold thepower door lock switch:
.to the LOCK position for more than 5
seconds to enable or disable the auto-
matic lock function, or
. to the UNLOCK position for more that 5
seconds to enable or disable the auto-
matic unlock function.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be turned OFF and ON again between each setting change.
LOCKING WITH MECHANICAL KEYThe driver’s door will be locked or unlocked
using the mechanical key.
1. Press the rear end of the driver’s outside
door handle
*1
to lift up the front end
*2.
2. With the outside door handle lifted up, usethe mechanical key and turn the key cylinder
cap
*A
counterclockwise to remove.
3-6
Pre-driving checks and adjustments
,QIRUPDWLRQ3URYLGHGE\

Black plate (158,1)
Model "R35-D" EDITED: 2008/ 5/ 20
From the passenger compartmentThe trunk can be opened with the emergency
trunk lid opener located on the floor in front of
the passenger’s seat.
1. Remove the board located on the floor infront of the passenger’s seat.
2. Insert the mechanical key into the emer-gency trunk lid opener and turn it clockwise
until it stops.NOTE:Because the trunk rigidity has been in-
creased to handle the high load on the rear
wing during vehicle operation, more force
is required to operate the mechanical key
(particularly when the vehicle is new) . Be
sure to turn the key clockwise until it
stops.
The fuel-filler door is located on the right and
rear side of the vehicle.
WARNING
.Gasoline is extremely flammable
and highly explosive under certain
conditions. You could be burned or
seriously injured if it is misused or
mishandled. Always stop engine
and do not smoke or allow open
flames or sparks near the vehicle
when refueling.
. Do not attempt to top off the fuel
tank after the fuel pump nozzle
shuts off automatically. Continued
refueling may cause fuel overflow,
resulting in fuel spray and possibly
a fire.
. Use only an original equipment type
fuel-filler cap as a replacement. It
has a built-in safety valve needed
for proper operation of the fuel
system and emission control sys-
tem. An incorrect cap can result in a
serious malfunction and possible
injury. It could also cause the mal-
function indicator light to come on.
. Never pour fuel into the throttle
3-22
Pre-driving checks and adjustments
FUEL-FILLER DOOR
,QIRUPDWLRQ3URYLGHGE\

Black plate (275,1)
Model "R35-D" EDITED: 2008/ 5/ 20
2. Fit the jack head into the dent
*A
of the
jack-up point by turning the jackscrew
clockwise with your fingers.
3. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut
wrench. Do not remove the wheel nuts
until the tire is off the ground.
4. Carefully raise the vehicle until the tire clears the ground. To lift the vehicle, securely hold
the jack lever and rod with both hands as
shown above.
Maintenance and do-it-yourself
8-41
,QIRUPDWLRQ3URYLGHGE\

Black plate (276,1)
Model "R35-D" EDITED: 2008/ 5/ 20
5. Remove the wheel nuts and then remove thewheel.NOTE:When putting a wheel on the ground, put it
down with the outer side of the wheel
facing up to prevent scratching of the
wheel surface.
6. Clean any mud or dirt from the surfacebetween the brake disc rotor
*1
and wheel
*2.
7. Tighten the wheel nuts by hand by turningthem clockwise until the tapered part
*A
of
each nut lightly contacts the seat part
*B
of
the wheel hole.
When replacing a front wheel, make sure the
hole in the wheel is aligned with the pin on
the brake disc rotor.
8-42
Maintenance and do-it-yourself
,QIRUPDWLRQ3URYLGHGE\