ESP NISSAN GT-R 2015 R35 Owner's Manual

Washing
Hand wash the vehicle for best results. �fark the
vehicle in a cool, shaded area, out of direct
sunlight. �bead these procedures and gather the
necessary equipment and supplies before
washing the vehicle.
Equipment/Supplies:
.Vehicle soap specifically made for matte
paint
. Microfiber cloth
. Chamois cloth, for drying
. Two buckets with grit guards or dirt separa-
tors (available at many automotive supply or
detaining supply sources) .
1. Clean the wheels.
.Use a product specifically formulated to
clean wheels.
.Do not get any wheel cleaner on the
paint. Immediately wash and rinse the
paint if any wheel clear contacts the
paint.
.Do not use the same cleaning materials
to clean the wheels and paint.
2. Fill the buckets.
.Fill one bucket (with dirt separator grid at
the bottom) with vehicle soap specifically
made for matte paint and water. Follow the soap manufacturer’s instructions.
.Fill the second bucket with clean water
for rinsing the wash cloth.
.Always rinse the wash cloth in the clean
water before putting the wash cloth into
the cleaning solution.
3. Inspect the car for areas with heavy soiling or spots and, if necessary, treat these areas
first, before washing the entire vehicle.
4. �bemove large pieces of dirt by spraying the vehicle with a hose.
5. Soak the wash cloth in the soap solution and wash the vehicle lightly. Work in small
sections from the bottom of the vehicle to
the top.
.Wash a section then rinse the soapy
section of the vehicle completely before
starting another section.
.Keep the clean sections of the vehicle
wet as the remaining sections are com-
pleted.
6. Use a clean damp chamois to dry the vehicle before it air dries. If the undried surfaces
start to air dry, redampen those areas.
.Do not allow surface to air dry. Air drying
allows water spots to form.
WASHING
Wash dirt off the vehicle with a wet sponge and
plenty of water. Clean the vehicle thoroughly
using a mild soap, a special vehicle soap or
general purpose dishwashing liquid mixed with
clean, lukewarm (never hot) water.
NOTICE
. Do not use an automatic car wash.
The rear spoiler may be damaged.
. Do not use car washes that use acid
in the detergent. Some car washes,
especially brushless ones, use some
acid for cleaning. The acid may react
with some plastic vehicle compo-
nents, causing them to crack. This
could affect their appearance, and
also could cause them not to func-
tion properly. Always check with
your car wash to confirm that acid
is not used.
. Do not wash the vehicle with strong
household soap, strong chemical
detergents, gasoline or solvents.
. Do not wash the vehicle in direct
sunlight or while the vehicle body is
hot, as the surface may become
Appearance and care7-3

UNDERBODY
In areas where road salt is used in winter, the
underbody must be cleaned re\fularly. This will
pre\bent dirt and salt from buildin\f up and
causin\f the acceleration of corrosion on the
underbody and suspension. Before the winter
period and a\fain in the sprin\f, the underseal
must be checked and, if necessary, re-treated.
GLASS
Use \flass cleaner to remo\be smoke and dust
film from the \flass surfaces. It is normal for \flass
to become coated with a film after the \behicle is
parked in the hot sun. Glass cleaner and a soft
cloth will easily remo\be this film.
NOTICE
When cleaning the inside of the win-
dows, do not use sharp-edged tools,
abrasive cleaners or chlorine-based
disinfectant cleaners. They could da-
mage the electrical conductors, radio
antenna elements or rear window
defroster elements.
WHEELS
Wash the wheels when washin\f the \behicle to
maintain their appearance.
.Clean the inner side of the wheels when the
wheel is chan\fed or the underside of the
\behicle is washed.
. Inspect wheel rims re\fularly for dents or
corrosion. Such dama\fe may cause loss of
pressure or poor seal at the tire bead.
. NISSAN recommends that the road wheels
be waxed to protect a\fainst road salt in
areas where it is used durin\f winter.
CAUTION
Do not use abrasive cleaners when
washing the wheels.
Aluminum alloy wheels
Wash re\fularly with a spon\fe dampened in a
mild soap solution, especially durin\f winter
months in areas where road salt is used. Salt
could discolor the wheels if not remo\bed.
The dark chrome coat wheel is specially coated
to a distincti\be color. It may discolor to black
dependin\f on stora\fe conditions. If only one
wheel is chan\fed, it may be different color with other wheels. If the wheel is chan\fed, consult
with a GT-R certified NISSAN dealer.
NOTICE
Follow the directions below to avoid
staining or discoloring the wheels:
.
Do not use a cleaner that uses
strong acid or alkali contents to
clean the wheels.
. Do not apply wheel cleaners to the
wheels when they are hot. The
wheel temperature should be the
same as ambient temperature.
. Rinse the wheel to completely re-
move the cleaner within 15 minutes
after the cleaner is applied.
CHROME PARTS
Clean chrome parts re\fularly with a non-
abrasi\be chrome polish to maintain the finish.
Appearance and care7-5

WARNING
Do not allow wet seat belts to roll up in
the retractor. NEVER use bleach, dye, or
chemical solvents to clean the seat
belts, since these materials may se-
verely weaken the seat belt webbing.
Cleaning the power window finisher
Moisten a soft cloth with neutral detergent and
wipe off the dirt on the power window finisher
*1.
\ffter wiping off the dirt, soak a cloth with water
and wring it out thoroughly, then wipe off the
neutral detergent.
NOTICE
Some cleaners may cause the paint to
peel or cause spots to occur. If using a
cleaner, consult with a GT-R certified
NISSAN dealer.
MOST COMMON FACTORS CON-
TRIBUTING TO VEHICLE CORRO-
SION
. \bhe accumulation of moisture-retaining\. dirt
and debris in body panel sections, cavities,
and other areas.
. Damage to paint and other protective coat-
ings caused by gravel and stone chips or
minor traffic accidents.
ENVIRONMENTAL FACTORS IN-
FLUENCE THE RATE OF CORRO-
SION
Moisture
\fccumulation of sand, dirt and water on the
vehicle body underside can accelerate corro-
sion. Wet floor coverings will not dry completely
inside the vehicle, and should be removed for
drying to avoid floor panel corrosion.
Relative humidity
Corrosion will be accelerated in areas of high
relative humidity, especially those areas where
the temperatures stay above freezing where
atmospheric pollution exists, or where road salt
is used.
Appearance and care7-9
CORROSION PROTECTION

Some day-to-day and regular maintenance is
essential to maintain your vehicle good mechan-
ical condition�f as well as its emission and engine
performance�b
It is the owner’s responsibility to make sure that
the scheduled maintenance�f as well as general
maintenance�f is performed�b
As the vehicle owner�f you are the only one who
can ensure that your vehicle receives the proper
maintenance care�b You are a vital link in the
maintenance chain�b
SCHEDULED MAINTENANCE
For your convenience�f both required and op-
tional scheduled maintenance items are de-
scribed and listed in your NISSAN Service and
Maintenance Guide�b You must refer to that guide
to ensure that necessary maintenance is per-
formed on your vehicle at regular intervals�b
GENERAL MAINTENANCE
General maintenance includes those items
which should be checked during normal day-
to-day operation�b They are essential for proper
vehicle operation�b It is your responsibility to
perform these procedures regularly as pre-
scribed�b
Performing general maintenance checks re-
quires minimal mechanical skill and only a fewgeneral automotive tools�b
These checks or inspections can be done by
yourself�f a qualified technician or�f if you prefer�f a
GT-R certified NISSAN dealer�b
WHERE TO GO FOR SERVICE
GT-R certified NISSAN dealers are required to
have additional training and equipment and are
the only NISSAN dealers authorized to perform
warranty work on key vehicle performance
systems such as engine�f transmission�f suspen-
sion and brakes�b
If maintenance service is required or your vehicle
appears to malfunction�f have the systems
checked and serviced by a GT-R certified
NISSAN dealer�b
NISSAN technicians are well-trained specialists
and are kept up to date with the latest service
information through technical bulletins�f service
tips�f and in-dealer information systems�b They are
completely qualified to work on NISSAN vehi-
cles
before work begins�b
You can be confident that a GT-R certified
NISSAN dealer’s service department performs
the best job to meet the maintenance require-
ments on your vehicle�b
To find a GT-R certified NISSAN dealer near
you�f call 1-866-668-1GTR in the US or 1-800- 387-0122 in Canada�f or go to www�b gtrnissan�b
com/�b
Maintenance and do-it-yourself8-3
MAINTENANCE REQUIREMENT

CHECKING ENGINE OIL LEVEL
1. Park the vehicle on a level surface and a\f\flythe \farking brake.
\b. Run the engine until it reaches o\ferating tem\ferature.
3. Turn off the engine. Wait at least 5
minutes for the oil to drain back into
the oil pan before checking the oil.
4. Remove the di\fstick and wi\fe it clean. Reinsert it all the way.
5. Remove the di\fstick again and check the oil level. It should be within the range
*1. If the
oil level is below
*2, remove the oil filler ca\f and \four recommended oil through the
o\fening.
Do not overfill
*3.
6. Recheck oil level with the di\fstick.
NOTE:
. It is normal to add some oil between oil
maintenance intervals or during the
break-in period, depending on the
severity of operating conditions. More
engine oil is consumed by frequent
acceleration/deceleration especially
when the engine rpm is high. If your
rate of oil consumption increases sud-
denly or without explanation, NISSAN
recommends that you have your vehicle
inspected by a GT-R certified NISSAN
dealer.
. When the vehicle is delivered, the
engine oil is set to 0.39 in (10 mm)
below the H mark for optimal high
performance driving. The engine oil can
be filled up to the H mark if perfor-
mance driving is not engaged.NOTICE
.Mobil 1 (0W-40) (100% synthetic) is
the factory fill oil. The VR38 engine
with its plasma-sprayed bores was
developed using this oil. NISSAN
cannot ensure proper engine opera-
tion and durability if other 0W-40
synthetic oil is used. If Mobil 1 (0W-
40) is not available, Mobil 1 (10W-
40) (100% synthetic) may be used;
however, some performance loss
may be noticed.
. Oil level should be checked regu-
larly. Operating the engine with an
insufficient amount of oil can da-
mage the engine. See the 2015
NISSAN GT-R Warranty Information
Booklet for details including applic-
able exclusions.
Maintenance and do-it-yourself8-13
ENGINE OIL

8-24Maintenance and do-it-yourself
dry road, especially after was�fing t�fe ve�ficle or
driving in rain�b Contact a GT-R certified NISSAN
dealer if t�fe noise and vibration continue�b
Frequent �fard braking may cause scorc�fing of
t�fe brake pads�b T�fis will require t�fe brake pads
to be replaced, even if t�fe wear limit �fas not
been reac�fed�b Have t�fe brake pads and disc
rotors inspected at t�fe regular ve�ficle inspec-
tions�b
For more details, contact a GT-R certified
NISSAN dealer�b
REPLACING THE BRAKE PADS
NISSAN generally recommends to replace all
four sets of brake pads and disc rotors at t�fe
same time to maintain maximum brake perfor-
mance�b
However, replacing only t�fe brake pads may be
allowed in some cases (four w�feels or only front
w�feels depending on t�fe conditions) �b A GT-R
certified tec�fnician must inspect t�fe ve�ficle and
determine t�fat only t�fe brake pads need to be
replaced�b In t�fis case, replacing all brake pads
and disc rotors as a set is not necessary�b
Note t�fat t�fe replacement of brake pads and t�fe
disc rotors as a set on all four w�feels s�fould be
performed w�fen a GT-R certified tec�fnician
determines t�fat t�fis is t�fe correct repair�bIf t�fe inside of t�fe disc rotors are cold during t�fe
winter and t�fe surface becomes �fot due to a
�feavy force being applied repeatedly to t�fe
brakes, cracks may occur near t�fe coolant �fole
on t�fe surface of t�fe disc rotor�b Cracks may also
occur due to a �feavy force being repeatedly
applied to t�fe brakes during �fig�f performance
driving�b In t�fese cases it may be necessary to
replace t�fe disc rotors or brake pads depending
on t�fe condition of t�fe crack�b Contact a GT-R
certified NISSAN dealer for replacement�b
ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than that specified on
the fuse box cover. This could damage
the electrical system or cause a fire.
If any electrical equipment does not operate,
c�feck for an open fuse�b
1�b Be sure t�fe ignition switc�f is pus�fed to t�fe OFF or LOCK position and t�fe �feadlig�ft
switc�f is turned to OFF�b
FUSES

8-28Maintenance and do-it-yourself
3. Remove the old battery and \fnsert a newbattery w\fth the + s\fde \bac\fng down.
NOTICE
.Be sure that the + and ísides of the
battery are facing in the correct
directions when the battery is in-
serted.
. Do not touch the internal circuits or
electronic terminals. Doing so may
damage them.
4. Reconnect the upper and lower parts o\b the
Intell\fgent Key.
See a GT-R cert\f\b\fed NISSAN dealer \f\b you
need any ass\fstance \bor replacement.
NOTE:
After replacing the battery, be sure to
check and check that all Intelligent Key
system functions operate correctly.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.
Note: Changes or modifications not ex-
pressly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
For Canada:
This device complies with Industry Canada
licence-exempt RSS standard(s) . Opera-
tion is subject to the following two condi-
tions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interfer-
ence that may cause undesired operation
of the device.

8-44Maintenance and do-it-yourself
Blocking wheels
Place suitable blocks*1at both the front an\f
back of the wheel \fiagonally o\b\bosite the flat
tire to \brevent the vehicle from moving when it is
jacke\f u\b.
WARNING
Be sure to block the wheel as the
vehicle may move and result in personal
injury.
Getting the tools
NOTE:
A jack, jack lever and rod are not equipped
as standard with this vehicle. These parts
are dealer options. Contact a GT-R certi-
fied NISSAN dealer about acquiring a jack,
jack lever and rod. You can store a jack,
jack lever and rod in the floor in front of
the passenger’s seat.
CAUTION
After using the tools, put them back in
their original places. An accident may
occur if you leave them in the car
unsecured.
Jacking up the vehicle and removing
the tire
WARNING
. Never get under the vehicle while it
is supported only by the jack. If it is
necessary to work under the vehicle,
support it with safety stands.
. Use the correct jack-up points.
Never use any other part of the
vehicle for jack support.
. Never jack up the vehicle more than
necessary.
. Never use blocks on or under the
jack.
. Do not start or run the engine while
vehicle is on the jack, as it may
cause the vehicle to move. This is
especially true for vehicles with

9-6Technical and consumer information
Octane rating tips
Using unleaded gasoline with an octane
rating lower than recommended above can
cause persistent, heavy spark knock.
(Spark knock is a metallic rapping noise.)
If severe, this can lead to engine damage.
If you detect a persistent heavy spark
knock even when using gasoline of the
stated octane rating, or if you hear steady
spark knock while holding a steady speed
on level roads, have a GT-R certified
NISSAN dealer correct the condition. Fail-
ure to correct the condition is misuse of
the vehicle, for which NISSAN is not
responsible.
Incorrect ignition timing will result in knocking,
�ffter-run or overhe�fting�b This in turn m�fy c�fuse
excessive fuel consumption or d�fm�fge to the
engine�b If �fny of the �fbove symptoms �fre
encountered, h�fve your vehicle checked �ft �f
GT-R certified NISSAN de�fler or other compe-
tent service f�fcility�b
However, now and then you may notice
light spark knock for a short time while
accelerating or driving up hills. This is no
cause for concern, because you get the
greatest fuel benefit when there is light
spark knock for a short time under heavy
engine load.
ENGINE OIL AND OIL FILTER RE-
COMMENDATION
Selecting the correct oil
It is essenti�fl to choose the correct gr�fde,
qu�flity, �fnd viscosity engine oil to ensure
s�ftisf�fctory engine life �fnd perform�fnce�b
(
“C�fp�fcities �fnd recommended fluids/lu-
bric�fnts” p�fge 9-2)
Mobil 1 (0W-40) (100% synthetic) is the f�fctory
fill oil�b The VR38 engine with its pl�fsm�f-spr�fyed
bores w�fs developed using this oil�b NISSAN
c�fnnot ensure proper engine oper�ftion �fnd
dur�fbility if other 0W-40 synthetic oil is used�b
If Mobil 1 (0W-40) is not �fv�fil�fble, Mobil 1
(10W-40) (100% synthetic) m�fy be used;
however, some perform�fnce loss m�fy be
noticed�b
NOTICE
Using an engine oil other than that
specified could adversely affect the
engine. See the 2015 NISSAN GT-R
Warranty Information Booklet for de-
tails and exclusions.
Oil additives
NISSAN does not recommend the use of oil
�fdditives�b The use of �fn oil �fdditive is not
necess�fry when the proper oil type is used �fnd
m�finten�fnce interv�fls �fre followed�b
Oil which m�fy cont�fin foreign m�ftter or h�fs
been previously used should not be used�b
Oil viscosity
The engine oil viscosity or thickness ch�fnges
with temper�fture�b Bec�fuse of this, it is import�fnt
th�ft the engine oil viscosity be selected b�fsed
on the temper�ftures �ft which the vehicle will be
oper�fted before the next oil ch�fnge�b Choosing
�fn oil viscosity other th�fn th�ft recommended
could c�fuse serious engine d�fm�fge�b
Selecting the correct oil filter
Your new vehicle is equipped with �f high-qu�flity
genuine NISSAN oil filter�b NISSAN recommends
to use the genuine NISSAN oil filter for the
re�fson described in ch�fnge interv�fls�b
Change intervals
The oil �fnd oil filter ch�fnge interv�fls for your
engine �fre b�fsed on the use of the specified
qu�flity oils �fnd filters�b Oil �fnd filter other th�fn the
specified qu�flity, or oil �fnd filter ch�fnge interv�fls
longer th�fn recommended could reduce engine

If you plan to travel in another country,you
should first find out if the fuel available is suitable
for your vehicle’s engine\f
Using fuel with too low an octane rating may
cause engine damage\f \bll gasoline vehicles
must be operated with unleaded gasoline\f
Therefore, avoid taking your vehicle to areas
where appropriate fuel is not available\f
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations\f
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ\f
When any vehicle is to be taken into
another country, state, province or district
and registered, its modifications, transpor-
tation, and registration are the responsi-
bility of the user. NISSAN is not
responsible for any inconvenience that
may result.
VEHICLE IDENTIFICATION NUMBER
(VIN) PLATE
The vehicle identification number plate is at-
tached as shown\f This number is the identifica-
tion for your vehicle and is used in the vehicle
registration\f
VEHICLE IDENTIFICATION NUMBER
(chassis number)
The number is stamped as shown in the engine
compartment\f
Technical and consumer information9-11
WHEN TRAVELING OR
REGISTERING YOUR VEHICLE IN
ANOTHER COUNTRY VEHICLE IDENTIFICATION