engine NISSAN GT-R 2022 Owners Manual

1 second.
NOTE:
When the battery is disconnected, the
memory for trips
is erased, and
both return to zero.
TACHOMETERThe tachometer indicates the engine
speed in revolutions per minute (rpm).
Do not rev the engine into the red zone
.
NOTICE
When engine speed approaches the
red zone, shift to a higher gear or
reduce engine speed. Operating the
engine in the red zone may cause
serious engine damage.
ENGINE COOLANT TEMPERATURE
GAUGEThe gauge indicates the engine coolant
temperature.
The engine coolant temperature is within
the normal range when the gauge needle
points within the zone
shown in the
illustration.
The engine coolant temperature varies
with the outside air temperature and
driving conditions.

NOTICE
If the gauge indicates engine coolant
temperature near the hot (H) end of
the normal range, reduce vehicle
speed to decrease temperature. If
gauge is over the normal range, stop
the vehicle as soon as safely possi-
ble. If the engine is overheated,
continued operation of the vehicle
may seriously damage the engine.
(
“If your vehicle overheats” page
6-8)
FUEL GAUGEThe gauge indicates the approximate
fuel level in the tank.
The gauge may move slightly during
braking, turning, acceleration, or going
up or down hills.
The gauge needle returns to E (Empty)
after the ignition switch is pushed to the
LOCK position.
Refill the fuel tank before the gauge
registers “E” (Empty).
The low fuel warning will be indicated on
the vehicle information display when the
fuel tank is getting low. Refuel as soon as
it is convenient, preferably before the gauge reaches “E”. There will be a small
reserve of fuel in the tank when the fuel
gauge needle reaches “E”. (
“Low fuel
warning” page 2-43)
The
indicates that the fuel-filler door
is located on the passenger’s side of the
vehicle. (
“Fuel-filler door” page 3-24)
NOTE:
If the vehicle runs out of fuel, the
Malfunction Indicator Light (MIL) may
come on. Refuel as soon as possible.
After a few driving trips, the
light
should turn off. If the light remains on
after a few driving trips, it is recom-
mended you have the vehicle inspected
by a GT-R certified NISSAN dealer.
(
“Malfunction Indicator Light (MIL)”
page 2-32)
Instruments and controls
2-9

TRANSMISSION POSITION INDICA-
TORThe transmission position indicator indi-
cates the gear positions.
The indicator blinks if it is not possible to
shift the gear when in the
position.
1. Upshift indicator (green)
2. Upshift indicator (yellow)
3. Upshift indicator (red)UPSHIFT INDICATORWhen the upshift indicator is set to on, the
indicators on the tachometer will illumi-
nate to help upshift at a constant engine
speed from any gear or to warn the driver
of over-revving.
The upshift indicator operates only when
the shift lever is in the
position. This
function consists of two modes that can
be selected on the vehicle information
display: AUTO setting and MANUAL
setting.

to go to ALERT > UPSHIFT. The
current status of the upshift indicator will
be shown on the UPSHIFT screen. Note
that the function is set to AUTO as the
factory default setting.
To change the upshift indicator mode,
choose SETTING on the UPSHIFT screen.
Set one of the following modes by push-
ing the NEXT switch
, and then push
ENTER
to complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push
and hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The
yellow indicator illuminates approxi-
mately 700 RPM before the red zone,
and the red indicator illuminates just
before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approxi- mately 5,500 RPM and illuminates at
6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during
break-in, set the upshift indicator to less
than 3,500 RPM. The green indicator
starts flashing approximately 500 RPM
before the set figure and illuminates from
the set figure. (
“Break-in schedule”
page 5-40)
NOTE:
. There may be a slight difference
between the timing of the upshift
indicator illumination and the tach-
ometer indication.
. When the battery terminal is discon-
nected, the set memory will be
erased and the mode returns to the
default.
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be ad-
justed when the ignition switch is in the
ON position. Push the switch to adjust the
brightness up
or down
. The bright-
ness level is shown on the vehicle infor-
mation display.
When the headlights are on, the bright-
ness of the interior switches is also
adjusted at the same time.

position. Operate the shift lever after
the system check indicator turns off.
. The shift lever cannot be moved if
the shift lever button is pushed
while the system check is being performed, even after the system
check is finished. Release the button
and push it again to operate the
shift lever.
. During winter or at other times when
the temperature is extremely low,
changes in the hydraulic response
characteristics may increase the
amount of time that is required for
the system check. During the system
check, a thudding operating noise
may occur or the engine speed may
decrease, however this does not
indicate that there is a malfunction.
Instruments and controls
2-15

OUTSIDE AIR TEMPERATUREThis displays the outside air temperature.
NOTE:
.The outside air temperature may not
be displayed correctly in the follow-
ing cases.
—The outside air temperature is
lower than −22°F (−30°C) or is
higher than 131°F (55°C).
— The vehicle is stopped or is driving
at a low speed (less than approxi-
mately 12 MPH (20 km/h)).
— The temperature in the engine
compartment is high. .
When the outside air temperature is
lower than 37°F (3°C), the low outside
temperature warning will be dis-
played and “ICY” is indicated on the
outside air temperature display.
(
“Alert” page 2-20)Instruments and controls
2-19

to change the time. Push and
hold the switch to increase the number
every 1 hour. A maximum of 6 hours can
be set.
NOTE:
The default setting is OFF.
Low outside temperature warning:
This alert informs the driver when the
outside air temperature is lower than 37°F
(3°C).
On the ICY screen, push the NEXT switch
to turn this warning ON/OFF.
NOTE:
The default setting is ON.
MaintenanceThis function can be used to set the
various maintenance intervals and to
check the engine oil level. The reminders
shown below are used to notify the driver
of the maintenance intervals.
NOTE:
Because these are displayed based on
the mileage driven, they do not indicate
the actual conditions of the vehicle. Use
these functions only as a reference.
Input the maintenance distance using the
following items:
. On each setting screen, push the
Instruments and controls
2-21

to change the mile-
age. Push and hold the switch to
increase the number every 600 miles
(1,000 km).
. Set to “—” to set no reminders.
. To reset the accumulated mileage to
zero, go to the RESET screen, then
push the NEXT switch
and confirm
with the ENTER switch.
NOTE:
. To restore the mileage to the origi-
nal figure after resetting, push the
NEXT switch
again.
. When the battery terminal is discon-
nected, the set mileage will be
erased and the settings will return
to their default settings.
Engine oil level:
This can be used to check the pre-start oil
level while the engine is running. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL > LEVEL.
If the low level reminder appears, check
the level using the engine oil dipstick.
(
“Checking engine oil level” page 8-9)

All-Wheel Drive (AWD) warning light
Cruise main switch indicator light
Anti-lock Braking System (ABS) warn-
ing light
Cruise set switch indicator light
Charge warning light
Exterior light indicator
Engine oil pressure warning light
Intelligent Key warning light
Front passenger air bag status light
Seat belt warning light
Low tire pressure warning light
High beam indicator light
Supplemental air bag warning light
Malfunction Indicator Light (MIL)
Turn signal/hazard indicator lights
Master warning lightTransmission warning lightVehicle Dynamic Control (VDC) off
indicator lightVehicle Dynamic Control (VDC) warn-
ing light
CHECKING LIGHTSWith all doors closed, apply the parking
brake, fasten the seat belts and place the
ignition switch in the ON position without
starting the engine. The following lights (if
so equipped) will come on:
,
or
,
,
,
The following lights (if so equipped) willcome on briefly and then go off:
,
or
,
,
,
,
,
If any light does not come on or operates
in a way other than described, it may
indicate a burned-out bulb and/or a
system malfunction. It is recommended
you have the system checked by a GT-R
certified NISSAN dealer.
WARNING/INDICATOR LIGHTS (red)See
“Warning display” page 2-36 and
“Vehicle information display” page 2-
13.
Brake warning light
This light functions for both the parking
brake and the foot brake systems.
WARNING LIGHTS, INDICATOR
LIGHTS AND AUDIBLE REMINDERS

Parking brake indicator:
When the ignition switch is in the ON
position, the light comes on when the
parking brake is applied.
Low brake fluid warning light:
When the ignition switch is in the ON
position, the light warns of a low brake
fluid level. If the light comes on while the
engine is running with the parking brake
not applied, stop the vehicle and perform
the following:
1. Check the brake fluid level. Add brakefluid as necessary. (
“Brake fluid”
page 8-11)
2. If the brake fluid level is correct, it is recommended you have the warning
system checked by a GT-R certified
NISSAN dealer.
Anti-lock Braking System (ABS) warning
indicator:
When the parking brake is released and
the brake fluid level is sufficient, if both
the brake warning light and the Anti-lock
Braking System (ABS) warning light illu-
minate, it may indicate the ABS is not
functioning properly. It is recommended
you have the brake system checked, and
if necessary repaired, by a GT-R certified
NISSAN dealer promptly. (
“Anti-lock
Braking System (ABS) warning light” page 2-29)
Brake pad wear warning indicator
(models with NCCB (NISSAN Carbon
Ceramic Brake) package):
When the brake warning light illuminates,
it may indicate that there is brake pad
wear. Have the brake system checked
and brake pads replaced as soon as
possible. It is recommended you contact
a GT-R certified NISSAN dealer for this
service.
WARNING
.
Your brake system may not be
working properly if the warning
light is on. Driving could be dan-
gerous. If you judge it to be safe,
drive carefully to the nearest
service station for repairs. Other-
wise, have your vehicle towed because driving it could be dan-
gerous.
. Pressing the brake pedal with the
engine stopped and/or low brake
fluid level may increase your
stopping distance and braking
will require greater pedal effort
as well as pedal travel.
. If the brake fluid level is below the
minimum or MIN mark on the
brake fluid reservoir, do not drive
until the brake system has been
checked. It is recommended you
contact a GT-R certified NISSAN
dealer.
Charge warning light
If the light comes on while the engine is
running, it may indicate the charging
system is not functioning properly. Turn
the engine off and check the alternator
belt. If the belt is loose, broken, missing or
if the light remains on, it is recommended
you see a GT-R certified NISSAN dealer
immediately.
Instruments and controls
2-27