display NISSAN GT-R 2022 Owners Manual

position.NOTE:
.
If the steering lock release malfunc-
tion indicator appears on the vehicle
information display when the igni-
tion switch is pressed, press the
ignition switch again while gently
turning the steering wheel left and
right. (
“Steering lock release
malfunction indicator” page 2-47)
. If the shiftwarning appears on the
vehicle information display when
the ignition switch is pushed, the
shift lever is in any position except
the
position. Move the shift lever
to the
position. (
“Shift “P”
warning” page 2-46)
. If the Intelligent Key battery dis-
charge indicator appears on the
vehicle information display, the In-
telligent Key battery is discharged
and the ignition switch will not
operate. Insert the Intelligent Key
into the key port to operate the
ignition switch. (
“Intelligent Key
battery discharge indicator” page 2-
48)
. When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
—The ignition switch is in the ACC
Starting and driving
5-11

position, and
— All doors are closed, and
— The shift lever is in the
of
the Intelligent Key port blinks and the
indicator appears on the vehicle informa-
tion display. (
“Intelligent Key insertion
indicator” page 2-47)
In this case, inserting the Intelligent Key
into the port allows you to start the
engine. Make sure that the mechanical
key side faces backward as illustrated.
Insert the Intelligent Key in the port until it
is latched and secured.
To remove the Intelligent Key from the port, push the ignition switch to the OFF
position and pull the Intelligent Key out of
the port.
NOTICE
Never place anything except the
Intelligent Key in the Intelligent Key
port. Doing so may cause damage to
the equipment.

position, and to
4,000 rpm when the engine oil or
coolant temperature is low or higher
than normal.
. If the ignition switch is pushed
before the shift lever is moved to
the
position, the ignition switch
will not change to the OFF position.
If this occurs, the SHIFT
warning
display appears on the vehicle in-
formation display. When stopping
the engine, be sure to move the shift
lever to the
position and then
push the ignition switch. Failure to
do so may result in discharge of the
battery. (“Shift “P” warning”
page 2-46)
. If the shift lever was in the
position when the engine was
stopped, then be sure to move the
shift lever to the
position before
starting the engine the next time. If the engine is started with the shift
lever in the
position, then it may
not be possible to drive the vehicle
even when the shift lever is moved
to the
position. If this
occurs, the SHIFTwarning appears
on the vehicle information display.
(
“Shift “P” warning” page 2-46)
CAUTION
If the engine was stopped soon
when the engine is hot, the cooling
fan may operate for approximately 2
minutes after the engine was
stopped to cool the components in
the engine compartment. When the
cooling fan is operating, be sure that
hands or other items do not get
caught in it.
DUAL CLUTCH TRANSMISSIONThe GT-R dual clutch transmission is a
newly-developed system that uses an
electronically controlled multiple-disc
wet clutch attached to the highly efficient
manual transmission. This transmission
has two driving modes.
.
position
and operate the paddle shifter to shift
down to 1st gear similar to a manual
transmission vehicle.
The GT-R dual clutch transmission was
developed specifically to maximize vehi-
cle performance and driving enjoyment.
The GT-R transmission components were
designed using different engineering
standards than typical passenger car
transmissions. Because of this, the GT-R
has different operating characteristics,
and various rattle noises may be heard
during some driving conditions because
Starting and driving
5-15
DRIVING THE VEHICLE

position to the
,
,or
or
position. All other positions
can be selected without pushing the
button.
Shift lever operation
Push the button while depressing
the brake pedal.Push the button.Just move the shift lever.Automatically returns.
position only when the
vehicle is completely stopped.
position:
Use this position for driving in reverse. A
chime will sound inside the vehicle and a
warning will appear in the vehicle infor-
mation display if the shift lever is in theposition for more than 5 minutes, or
when the driver’s door is opened while
the shift lever is in the
position.
and
to alternately change
each other. The position indicator indi-
cates the gear position with the indica-
tion of “A” or “M”.
.

position. Be sure to depress the
brake pedal.
NOTICE
. Be sure to observe the following
precautions. Failure to do so may
result in shift lever malfunction.
— Do not spill water, beverages
or other liquids on the shift
lever.
— Do not allow sand or similar substances to contact the
shift lever.
. Develop the habit of performing
the operations marked with “
”
without pressing the button. If
the button is pressed at these
times, there is the possibility that
the lever could accidentally enter
the
or
positions.
. When the vehicle is hot, the area
around the shift lever may be hot
or may produce an unusual
sound, however this does not
indicate that there is a malfunc-
tion.
. Avoid depressing the brake and
accelerator pedals at the same
time. Depressing both pedals at
the same time could cause the
clutch to overheat and accelerate deterioration.
NOTE:
. When moving the shift lever out of
the
position, it may not be possi-
ble to move the shift lever if the
button is pressed before the brake
pedal is depressed. Press the button
only after depressing the brake
pedal.
. Do not place coins or other small
objects in the area around the shift
lever. These objects may get stuck in
the shift gate and prevent the shift
lever from moving into a position.
Sometimes, you may not be able to
retrieve these objects.
. Immediately after a cold start, while
the transmission system check dis-
play (“T/M SYSTEM CHECK IN PRO-
CESS”) appears on the vehicle
information display, the shift lever
cannot be moved out of the
position. This is because a check of
the transmission system is in pro-
gress. This does not indicate that
there is a malfunction. Move the
shift lever after the message on the
vehicle information display turns off.
. The shift lever knob and console-

2. Accelerate your vehicle to the desiredspeed, push the SET/COAST switch
and release it. (The SET indicator will
illuminate in the meter.) Take your
foot off the accelerator pedal. Your
vehicle will maintain the set speed.
NOTE:
If the vehicle speed reaches approxi-
mately 3 MPH (5 km/h) over the set
speed, the set speed on the vehicle
information display blinks.Passing another vehicleTo pass another vehicle, depress the
accelerator pedal. When you release the
pedal, the vehicle will return to the pre- viously set speed.
Increasing the set vehicle speedTo reset at a faster cruising speed, use
one of the following methods:
.
Depress the accelerator pedal. When
the vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the RESUME/ACCELER-
ATE switch. When the vehicle attains
the speed you desire, release the
switch.
. Push and then quickly release the
RESUME/ACCELERATE switch. Each
time you do this, the set speed will
increase by about 1 MPH or 1 km/h.Decreasing the set vehicle speedTo reset at a slower cruising speed, use
one of the following methods:
.Lightly tap the brake pedal. When the
vehicle attains the desired speed,
push and release the SET/COAST
switch.
. Push and hold the SET/COAST switch.
Release the switch when the vehicle
slows down to the desired speed.
. Push and then quickly release the
Starting and driving
5-37

NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal.
Doing so may cause the clutch to
overheat and result in transmission
damage. Use the brakes to prevent
the vehicle from moving.
The hill start assist system automatically
keeps the brakes applied to help prevent
the vehicle from rolling backwards in the
time it takes the driver to release the
brake pedal and apply the accelerator
when the vehicle is stopped on a hill.
Hill start assist will operate automatically
under the following conditions:
. The shift lever is moved to a forward
or reverse position.
. The vehicle is stopped completely on a
hill by applying the brake.
The maximum holding time is 2 seconds.
After 2 seconds the vehicle will begin to
roll back and hill start assist will stop operating completely.
Hill start assist will not operate when the
shift lever is moved to the
or
position
or on a flat and level road.
NOTE:
This system does not function when the
Vehicle Dynamic Control VDC) system
warning appears on the vehicle infor-
mation display located in the tach-
ometer. (
“Vehicle Dynamic Control
(VDC) system warning” page 2-40)Starting and driving
5-39
HILL START ASSIST SYSTEM

CAUTION
.Keep the interior of the vehicle as
quiet as possible to hear the tone
clearly. Excessive noise (such as
audio system volume or an open
vehicle window) will interfere
with the tone and it may not be
heard.
. Keep the sonar (located on the
bumper fascia) free from snow,
ice and large accumulations of
dirt (do not clean the sonar with
sharp objects). If the sonar is
covered, it will affect the accuracy
of the sonar system.
. The sonar system may not oper-
ate correctly if a license plate
cover is installed.
The sonar system sounds a tone to warn
the driver of obstacles near the bumper.
The sonar indicator will also appear in the
touch screen display. (
“Sonar indica-
tor” page 5-49.) The system detects front
obstacles when the shift lever is in the
position or
position and both front and
SONAR SYSTEM

position.
The system may not detect objects at
speeds above 6 MPH (10 km/h) and may
not detect certain angular or moving
objects.
Refer to the illustration for approximate
zone coverage areas. As you move closer
to the obstacle, the rate of the tone
increases. When you move even closer
to the obstacle, the tone will sound
continuously.
The sensitivity level of the sonar can be
adjusted (higher or lower) in the sonar
setting display. (

could affect the proper operation
of the TPMS.
. Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction
of the tire pressure sensors.
NOTE:
. You can check the pressure of all
four tires on the touch screen dis-
play. See the separate Multi Func-
tion Display Owner’s Manual.
. The tires of this vehicle are filled
with nitrogen gas. When the tire
pressure is low, fill the tires with
nitrogen. It is recommended you
contact a GT-R certified NISSAN
dealer for information on filling the
tires with nitrogen.
. If nitrogen is not available, com-
pressed air may be safely used
under normal driving conditions.
However, NISSAN recommends re-
filling with nitrogen for maximum
tire performance.
RUN-FLAT TIRESRun-flat tires are those tires that can be
used temporarily if they are punctured.
(
“Run-flat tires” page 8-36)
Also, see the tire safety information in the
Warranty Information Booklet.
position.
4. Turn off the engine.
5. Raise the hood to warn other traffic,