NISSAN GT-R 2022 Owners Manual

5. Remove the wheel nuts and thenremove the wheel.
NOTE:
When putting a wheel on the
ground, put it down with the outer
side of the wheel facing up to pre-
vent scratching of the wheel surface.
and wheel
.

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

Except for NISMO and Track edi-
tion engineered by nismo models97 ft-lb (132 N

in a safe
place. To purchase a lock key, con-
tact a GT-R certified NISSAN dealer
with your original codeon the key
code card.
. When you ask for a service at a GT-R
certified NISSAN dealer, make sure
to keep the lock key in the vehicle.
Otherwise, tires cannot be removed
and any service requiring the re-
moval of the wheels cannot be
performed.
Do-it-yourself
8-47

position (UNLOCK)
for more than 5 seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the
hazard indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again be-
tween each setting change.
When the automatic door unlock system
is deactivated, the doors do not unlock
when the ignition switch is placed in the
OFF position. To unlock the door manu-
ally, use the inside lock knob or the power
door lock switch (driver

will lock the
driver

WARNING
CAUTION
.Be sure to carry the Intelligent
Key with you when operating the
vehicle.
. Never leave the Intelligent Key in
the vehicle when you leave the
vehicle.
. The Intelligent Key is always commu-
nicating with the vehicle as it receives
radio waves. The Intelligent Key sys-
tem transmits weak radio waves. En-
vironmental conditions may interfere
with the operation of the Intelligent
Key system under the following oper-
ating conditions. In such cases, cor-
rect the operating conditions before
using the Intelligent Key function or
use the mechanical key.
— When operating near a location
where strong radio waves are
transmitted, such as a TV tower,
power station and broadcasting
station.
— When in possession of wireless equipment, such as a cellular tele-
phone, transceiver, and CB radio.
INTELLIGENT KEY SYSTEM

Intelligent Key operating rangeThe Intelligent Key functions can only be
used when the Intelligent Key is within
the specified operating range from the
request switch. The operating range is
within 31.50 in (80 cm) from each request
switch.
NOTE:
.When the Intelligent Key battery is
discharged or strong radio waves
are present near the operating loca-
tion, the Intelligent Key system’s
operating range becomes narrower,
and the Intelligent Key may not
function properly. .
If the Intelligent Key is too close to
the door glass, handle or rear bum-
per, the request switches may not
function.
. When the Intelligent Key is within
the operating range, it is possible for
anyone who does not carry the
Intelligent Key to push the request
switch to lock/unlock the doors.
Intelligent Key operationYou can lock or unlock the doors without
taking the key out from your pocket or
bag.

SONAR SYSTEM OFF SWITCHThe sonar system OFF switch on the
lower side of the instrument panel allows
the driver to turn the sonar system on
and off. To turn the sonar system on and
off, the ignition switch must be in the ON
position. The indicator light
on the
switch will turn off when the system is
turned off. If the indicator light flashes it
may indicate a malfunction in the sonar
system.
The sonar system will turn on automati-
cally under the following conditions.
. When the shift lever is placed in the
position. .
When vehicle speed decreases below
approximately 6 MPH (10 km/h).
. When the ignition switch is placed in
the OFF position and turned back to
the ON position again.