display NISSAN GT-R 2022 Workshop Manual

HOW TO TURN ON AND OFF PRE-
DICTIVE COURSE LINESIf the RearView Monitor is in operation
and the rear view is displayed, turn on
and off the predictive course line setting
according to the following procedure.
1. Touch the touch screen display.
2. Touch the “Predictive Course Lines”key to turn the feature on or off.
If the RearView Monitor is not in opera-
tion, change the setting according to the
following procedure.
1. Touch the “Settings” key on theLaunch Bar
on the touch screen
display.
2. Touch the “Camera” key.
3. Touch the “Predictive Course Lines” key. The indicator illuminates when
the item is turned on.
SONAR INDICATORThe sonar indicator will appear in the
RearView Monitor display. (
“Sonar
system” page 5-48)
REARVIEW MONITOR SYSTEM LIM-
ITATIONS
WARNING
Listed below are the system limita-
tions for RearView Monitor. Failure to
operate the vehicle in accordance
with these system limitations could
result in serious injury or death.
. The system cannot completely
eliminate blind spots and may
not show every object.
. Underneath the bumper and the
corner areas of the bumper can-
not be viewed on the RearView
Monitor because of its monitoring
range limitation. The system will
not show small objects below the
bumper, and may not show ob-
jects close to the bumper or on
the ground.
. Objects viewed in the RearView
Monitor differ from actual dis-
tance because a wide-angle lens
Display screen, heater, air conditioner and audio systems
4-7

is used.
. Objects in the RearView Monitor
will appear visually opposite
compared to when viewed in the
rearview and outside mirrors.
. Use the displayed lines as a re-
ference. The lines are highly af-
fected by the number of
occupants, fuel level, vehicle po-
sition, road conditions and road
grade.
. Make sure that the trunk lid is
securely closed when backing up.
. Do not put anything on the rear-
view camera. The rearview cam-
era is installed above the license
plate.
. When washing the vehicle with
high-pressure water, be sure not
to spray it around the camera.
Otherwise, water may enter the
camera unit causing water con-
densation on the lens, a malfunc-
tion, fire or an electric shock.
. Do not strike the camera. It is a
precision instrument. Otherwise,
it may malfunction or cause da-
mage resulting in a fire or an
electric shock. The following are operating limitations
and do not represent a system malfunc-
tion:
.
When the temperature is extremely
high or low, the screen may not clearly
display objects.
. When strong light is directly coming
on the camera, objects may not be
displayed clearly.
. Vertical lines may be seen in objects
on the screen. This is due to strong
reflected light from the bumper.
. The screen may flicker under fluores-
cent light.
. The colors of objects on the RearView
Monitor may differ somewhat from
the actual color of objects.
. Objects on the monitor may not be
clear in a dark environment.
. There may be a delay when switching
to the RearView Monitor screen.
. If dirt, rain or snow accumulates on
the camera, the RearView Monitor
may not display objects clearly. Clean
the camera.
. Do not use wax on the camera win-
dow. Wipe off any wax with a clean
cloth dampened with mild detergent
diluted with water.
SYSTEM MAINTENANCE
CAUTION
.Do not use alcohol, benzine or
thinner to clean the camera. This
will cause discoloration. To clean
the camera, wipe with a cloth
dampened with diluted mild
cleaning agent and then wipe
with a dry cloth.
. Do not damage the camera as the
monitor screen may be adversely
affected.

, the RearView Monitor may not
display objects clearly. Clean the camera
by wiping it with a cloth dampened with a
diluted mild cleaning agent and then
wiping it with a dry cloth.

and
located on the
instrument panel help maintain a con-
stant temperature. Do not put anything
on or around the sensors.
IN-CABIN MICROFILTERThe air conditioning system is equipped
with an in-cabin microfilter which collects
dirt, dust, etc. To make sure the air
conditioner heats, defogs, and ventilates
efficiently, replace the filter in accordance
with the maintenance schedule in the “9.
Maintenance and schedules” section of
this manual. It is recommended to see a
NISSAN dealer or GT-R certified NISSAN
dealer to replace the filter.
The filter should be replaced if air flow
is extremely decreased or when win-
dows fog up easily when operating
heater or air conditioning system.
Display screen, heater, air conditioner and audio systems
4-13

is located on the
rear part of the vehicle roof. When installing a car phone or a CB radio
in your vehicle, be sure to observe the
following cautions, otherwise the new
equipment may adversely affect the elec-
tronic control modules and electronic
control system harness.
CAUTION
.
Keep the antenna as far away as
possible from the electronic con-
trol modules.
. Keep the antenna wire more than
8 in (20 cm) away from the
electronic control system har-
ness. Do not route the antenna
wire next to any harness.
. Adjust the antenna standing-
wave ratio as recommended by
the manufacturer.
. Connect the ground wire from the
CB radio chassis to the body.
. For details, it is recommended
you visit a NISSAN dealer or GT-R
certified NISSAN dealer.
Display screen, heater, air conditioner and audio systems
4-15
CAR PHONE OR CB RADIO

.You can also check the pressure of all
tires on the touch screen display.
Refer to the separate Multi Function
Display Owner’s Manual.
. The tire pressure sensor should be
reset anytime the wheels or tires are
removed or replaced.
. If the tire is removed in order to
replace the tire pressure sensor bat-
tery, it may not be possible to reuse
the removed tire from the wheel. To
replace the tire pressure sensor bat-
tery, it is recommended you contact a
GT-R certified NISSAN dealer.
WARNING
.If the low tire pressure warning
light illuminates while driving,
avoid sudden steering maneu-
vers or abrupt braking, reduce
vehicle speed, pull off the road
to a safe location and stop the
vehicle as soon as possible. Driv-
ing with under-inflated tires may
permanently damage the tires
and increase the likelihood of tire
failure. Serious vehicle damage
could occur and may lead to an
accident and could result in ser-
ious personal injury. Check the tire pressure for all four tires.
Adjust the tire pressure to the
recommended COLD tire pressure
shown on the Tire and Loading
Information label to turn the low
tire pressure warning light off. If
the light still illuminates while
driving after adjusting the tire
pressure, a tire may be flat
(
“Run-flat tires” page 6-4) or
the TPMS may be malfunctioning.
If no tire is flat and all tires are
properly inflated, have the vehicle
checked. It is recommended you
have the vehicle checked by a
GT-R certified NISSAN dealer.
. Although you can continue driv-
ing with a punctured run-flat tire,
remember that vehicle handling
stability is reduced, which could
lead to an accident and personal
injury. Also, driving a long dis-
tance at high speeds may da-
mage the tires.
. Do not drive at speeds above 50
MPH (80 km/h) and do not drive
more than 50 miles (80 km) with a
punctured run-flat tire. The actual
distance the vehicle can be driven
on a flat tire depends on outside
temperature, vehicle load, road conditions and other factors.
. When a wheel is replaced, the
TPMS will not function and the
low tire pressure warning light
will flash for approximately 1
minute. The light will remain on
after 1 minute. It is recommended
you contact your GT-R certified
NISSAN dealer as soon as possi-
ble for tire replacement and/or
system resetting.
. Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. Do not inject any tire liquid or
aerosol tire sealant into the tires,
as this may cause a malfunction
of the tire pressure sensors.
NOTICE
.The TPMS may not function prop-
erly when the wheels are
equipped with tire chains or the
wheels are buried in snow.
. The TPMS may not function prop-
erly if the TPMS sensor is not
reset and when wheels/tires from

position.NOTE:
.
If the steering lock release malfunc-
tion indicator appears on the vehicle
information display when the igni-
tion switch is pressed, press the
ignition switch again while gently
turning the steering wheel left and
right. (
“Steering lock release
malfunction indicator” page 2-47)
. If the shiftwarning appears on the
vehicle information display when
the ignition switch is pushed, the
shift lever is in any position except
the
position. Move the shift lever
to the
position. (
“Shift “P”
warning” page 2-46)
. If the Intelligent Key battery dis-
charge indicator appears on the
vehicle information display, the In-
telligent Key battery is discharged
and the ignition switch will not
operate. Insert the Intelligent Key
into the key port to operate the
ignition switch. (
“Intelligent Key
battery discharge indicator” page 2-
48)
. When all of the following conditions
are met for 60 minutes, the battery
saver system will cut off the power
supply to prevent battery discharge.
—The ignition switch is in the ACC
Starting and driving
5-11

position, and
— All doors are closed, and
— The shift lever is in the
of
the Intelligent Key port blinks and the
indicator appears on the vehicle informa-
tion display. (
“Intelligent Key insertion
indicator” page 2-47)
In this case, inserting the Intelligent Key
into the port allows you to start the
engine. Make sure that the mechanical
key side faces backward as illustrated.
Insert the Intelligent Key in the port until it
is latched and secured.
To remove the Intelligent Key from the port, push the ignition switch to the OFF
position and pull the Intelligent Key out of
the port.
NOTICE
Never place anything except the
Intelligent Key in the Intelligent Key
port. Doing so may cause damage to
the equipment.

position, and to
4,000 rpm when the engine oil or
coolant temperature is low or higher
than normal.
. If the ignition switch is pushed
before the shift lever is moved to
the
position, the ignition switch
will not change to the OFF position.
If this occurs, the SHIFT
warning
display appears on the vehicle in-
formation display. When stopping
the engine, be sure to move the shift
lever to the
position and then
push the ignition switch. Failure to
do so may result in discharge of the
battery. (“Shift “P” warning”
page 2-46)
. If the shift lever was in the
position when the engine was
stopped, then be sure to move the
shift lever to the
position before
starting the engine the next time. If the engine is started with the shift
lever in the
position, then it may
not be possible to drive the vehicle
even when the shift lever is moved
to the
position. If this
occurs, the SHIFTwarning appears
on the vehicle information display.
(
“Shift “P” warning” page 2-46)
CAUTION
If the engine was stopped soon
when the engine is hot, the cooling
fan may operate for approximately 2
minutes after the engine was
stopped to cool the components in
the engine compartment. When the
cooling fan is operating, be sure that
hands or other items do not get
caught in it.
DUAL CLUTCH TRANSMISSIONThe GT-R dual clutch transmission is a
newly-developed system that uses an
electronically controlled multiple-disc
wet clutch attached to the highly efficient
manual transmission. This transmission
has two driving modes.
.
position
and operate the paddle shifter to shift
down to 1st gear similar to a manual
transmission vehicle.
The GT-R dual clutch transmission was
developed specifically to maximize vehi-
cle performance and driving enjoyment.
The GT-R transmission components were
designed using different engineering
standards than typical passenger car
transmissions. Because of this, the GT-R
has different operating characteristics,
and various rattle noises may be heard
during some driving conditions because
Starting and driving
5-15
DRIVING THE VEHICLE

position to the
,
,or
or
position. All other positions
can be selected without pushing the
button.
Shift lever operation
Push the button while depressing
the brake pedal.Push the button.Just move the shift lever.Automatically returns.
position only when the
vehicle is completely stopped.
position:
Use this position for driving in reverse. A
chime will sound inside the vehicle and a
warning will appear in the vehicle infor-
mation display if the shift lever is in theposition for more than 5 minutes, or
when the driver’s door is opened while
the shift lever is in the
position.
and
to alternately change
each other. The position indicator indi-
cates the gear position with the indica-
tion of “A” or “M”.
.