engine NISSAN JUKE 2015 F15 / 1.G Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2015, Model line: JUKE, Model: NISSAN JUKE 2015 F15 / 1.GPages: 383, PDF Size: 8.79 MB
Page 257 of 383
> ( G L W 0 R G H O ) ' @
GUID-74 08FE11-64BC -4759-BC8E-07366732C0C9
1. Apply theparking brake.
2. Move theshift lever tothe P(Park) orN
(Neutral) position.(Pisrecommended.)
The starter isdesigned nottooperate unless
the shift lever isin either ofthe above
positions.
Manual Transmission (MT)models:
Move theshift lever tothe N(Neutral)
position. Depresstheclutch pedalfullyto
the floor.
The starter isdesigned nottooperate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried
when operating theignition switch.
3. Push theignition switchtothe ON position.
Depress thebrake pedal(CVTmodels) or
the clutch pedal(MTmodels) andpush the
ignition switchtostart theengine.
T o start theengine immediately ,push and
release theignition switchwhiledepressing
the brake pedal withtheignition switchin
any position.
.
If the engine isvery hard tostart in
extremely coldweather orwhen restart-
ing, depress theaccelerator pedalalittle
(approximately 1/3tothe floor) andwhile
holding, cranktheengine. Release the
accelerator pedalwhentheengine starts.
.
If the engine isvery hard tostart because
it is flooded, depresstheaccelerator
pedal allthe way tothe floor andhold it.
Push theignition switchtothe ON
position tostart cranking theengine.
After 5or 6seconds, stopcranking by
pushing theignition switchtoOFF .After
cranking theengine, releasetheaccel-
erator pedal. Cranktheengine withyour
foot offthe accelerator pedalby
depressing thebrake pedal andpushing
the push-button ignitionswitchtostart
the engine. Ifthe engine starts,butfails
to run, repeat theabove procedure.
CAUTION
Do not operate thestarter formore
than 15seconds atatime. Ifthe engine
does notstart, pushtheignition switch
to OFF andwait 10seconds before
cranking again,otherwise thestarter
could bedamaged.
4. Warm-up
Allow theengine toidle foratleast 30
seconds afterstarting. Donot race the
engine whilewarming itup. Drive at
moderate speedforashort distance first, especially
incold weather. Incold weather,
keep theengine running foraminimum of2-
3 minutes beforeshutting itoff. Starting and
stopping theengine overashort period of
time maymake thevehicle moredifficult to
start.
When racing theengine upto4,000 rpmor
more under noload condition, theengine
will enter thefuel cutmode.
5. To stop theengine, movetheshift lever to
the P(Park) position (CVTmodels) ormove
the shift lever tothe N(Neutral) position(MT
models) ,and push theignition switchtothe
OFF position.
NO TE:
Care should betaken toavoid situations
that canlead topotential batterydischarge
and potential no-startconditions suchas:
1. Installation orextended useofelectro-
nic accessories thatconsume battery
power whentheengine isnot running
(Phone chargers, GPS,DVDplayers,
etc .)
2. Vehicle isnot driven regularly and/or
only driven shortdistances.
In these cases, thebattery mayneed tobe
charged tomaintain batteryhealth.
Starting anddriving
5-13
ST ARTING THEENGINE
& R Q G L W L R Q
Page 258 of 383
> ( G L W 0 R G H O ) ' @
5-14
Starting anddriving
GUID-00 99E665-725B -489E-B596-F5A3F4CD54DB
CONTINUOUS LY VARIABLE TRANS-
MISSION (CVT)
GUID-C69 9DF0B-987D -4AD2-879E-728294 24A200
The Continuously Variable Transmission (CVT)
in your vehicle iselectronically controlledto
produce maximum powerandsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.
Follow theseprocedures formaximum vehicle
performance anddriving enjoyment.
Engine powermaybeautomatically re-
duced toprotect theCVT ifthe engine
speed increases quicklywhendriving on
slippery roadsorwhile being tested on
some dynamometers.
Starting thevehicle
GUID-5D2 73D53-F49E -430A-9675-C A17371F1DFA
1. After starting theengine, fullydepress the
foot brake pedalbefore moving theshift
lever outofthe P(Park) position.
This CVTisdesigned sothat thefoot
brake pedalmustbedepressed before
shifting fromP(Park) toany driving
position whiletheignition switchisin
the ONposition.
The shift lever cannot bemoved outof
the P(Park) position andinto anyof
the other positions ifthe ignition
switch isplaced inthe LOCK ,OFF or
ACC position orifthe key isremoved. 2.
Keep thefoot brake pedaldepressed, push
the shift lever button andmove theshift lever
to adriving position.
3. Release theparking brakeandfoot brake
pedal, andthen gradually startthevehicle in
motion.
WARNING
. Do not depress theaccelerator
pedal whileshifting fromP(Park)
or N(Neutral) toR(Reverse) ,D
(Drive) ,or manual shiftmode (ifso
equipped) .Always depress the
brake pedaluntilshifting iscom-
pleted. Failure todo socould cause
you tolose control andhave an
accident.
. Cold engine idlespeed ishigh, so
use caution whenshifting intoa
forward orreverse gearbefore the
engine haswarmed up.
. Never shifttoP(Park) orR(Re-
verse) whilevehicle ismoving. Fail-
ure todo socould cause youtolose
control andhave anaccident.
CAUTION
. Except inan emergency, donot shift
to the N(Neutral) positionwhile
driving. Coasting withthetransmis-
sion inthe N(Neutral) positionmay
cause serious damage tothe trans-
mission.
. When stopping thevehicle onan
uphill grade, donot hold thevehicle
by depressing theaccelerator pedal.
The foot brake should beused for
this purpose.
. Do not downshift abruptlyonslip-
pery roads. Thismay cause aloss of
control.
DRIVING THEVEHICLE
& R Q G L W L R Q
Page 259 of 383
> ( G L W 0 R G H O ) ' @
SSD1140
T o move theshift lever,
: Push
thebutton
*
A
while depressing the
brake
pedal.
: Push
thebutton
*
A
.
: Just
move theshift lever.
Shifting
GUID-8E3 3D228-CFD 5-4E80-8A5F -A2EC598FE23A
After starting theengine, fullydepress thebrake
pedal, pushtheshift lever button andmove the
shift lever fromtheP(Park) position toany ofthe
desired shiftpositions.
WARNING
Apply theparking brakeifthe shift lever
is in any position whiletheengine is
not running. Failuretodo socould
cause thevehicle tomove unexpectedly
or roll away andresult inserious
personal injuryorproperty damage.
If the ignition switchisplaced inthe OFF or
ACC position forany reason whiletheshift lever
is in any positions otherthantheP(Park) ,the
ignition switchcannot beplaced inthe LOCK
position.
If the ignition switchcannot beplaced inthe
L OCK position, performthefollowing steps:
1. Apply theparking brakewhenthevehicle is
stopped.
2. Place theignition switchinthe ON position
while depressing thefoot brake pedal.
3. Move theshift lever tothe P(Park) position.
4. Place theignition switchinthe OFF position.
CAUTION
T o prevent transmission damage,move
the shift lever tothe P(Park) orR
(Reverse) positiononlywhen thevehi-
cle iscompletely stopped.
P (Park) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition whenthevehicle isparked or
when starting theengine. Makesurethevehicle
is completely stopped.Thebrake pedalmust
be depressed andtheshift lever button
pushed into move theshift lever fromN
(Neutral) orany drive position toP(Park) .
Apply theparking brake.Whenparking onahill,
apply theparking brakefirst,then move theshift
lever tothe P(Park) position.
R (Reverse) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition toback up.Make surethe
vehicle iscompletely stoppedbeforeselecting
the R(Reverse) position.Thebrake pedal
must bedepressed andtheshift lever
button pushed into move theshift lever
from P(Park) ,N (Neutral) orany driving
position toR(Reverse) .
N (Neutral) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Neither forward norreverse gearisengaged.
Starting anddriving
5-15
& R Q G L W L R Q
Page 260 of 383
> ( G L W 0 R G H O ) ' @
5-16
Starting anddriving
The engine canbestarted inthis position. You
may shift toN(Neutral) andrestart astalled
engine whilethevehicle ismoving.
D (Drive) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition forallnormal forward driving.
JVS0388X
Paddle shifter(ifso equipped)
Manual shiftmode (ifso equipped)
GUID-D71 2A263-68A D-455F-8166 -C902EBCAB071
When theshift lever isshifted fromtheD(Drive)
position tothe manual shiftgate, thetransmis-
sion enters themanual shiftmode. Shiftranges
can beselected manually bymoving theshift
lever upordown, orpulling theright-side orleft-
side paddle shifter(ifso equipped) .
In the manual shiftmode, theshift range is
displayed onthe position indicator inthe meter. Shift
ranges upordown onebyone asfollows:
Except forNISMO RSmodels:
M1 ?
M2?
M3?
M4?
M5 ?
M6 ?
M7
/ / /// /
NISMO RSmodels:
M1 ?
M2 ?
M3 ?
M4 ?
M5 ?
M6 ?
M7 ?
M8
/ // // / /
. When shifting up,move theshift lever tothe
+ (up) side orpull theright-side paddle
shifter (+)
*
A
(if so equipped) .The
transmission shiftstoahigher range.
. When shifting down,movetheshift lever to
the
Page 261 of 383
> ( G L W 0 R G H O ) ' @
after ashort period oftime. Ifyou want to
return tothe D(Drive) position manually ,pull
and hold thepaddle shifterforabout 1.5
seconds.
M7 (7th) (except forNISMO RSmodels) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
M8 (8th) (NISMO RSmodels) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition forallnormal forward drivingat
highway speeds.
M6 (6th) andM5(5th) (except forNISMO
RS models) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
M7 (7th) andM6(6th) (NISMO RSmodels) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use these positions whendriving uplong
slopes, orfor engine braking whendriving down
long slopes.
M4 (4th) ,M3 (3rd) andM2(2nd) (except for
NISMO RSmodels) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
M5 (5th) ,M4 (4th) ,M3 (3rd) andM2(2nd)
(NISMO RSmodels) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use these positions forhill climbing orengine
braking ondownhill grades.
M1 (1st) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition whenclimbing steephills
slowly ordriving slowlythrough deepsnow,
sand ormud, orfor maximum enginebraking on
steep downhill grades. .
Remember nottodrive athigh speeds for
extended periodsoftime inlower thanM7
(except forNISMO RSmodels) orM8
(NISMO RSmodels) range.Thisreduces
fuel economy .
. Inthe manual shiftmode, thetransmis-
sion maynotshift tothe selected
range. Thishelps maintain drivingper-
formance andreduces thechance of
vehicle damage orloss ofcontrol.
When thissituation occurs,theCon-
tinuously Variable Transmission (CVT)
position indicator lightwillblink and
the chime willsound.
. Inthe manual shiftmode, thetransmis-
sion automatically shiftsdownto1st
gear before thevehicle comestoa
stop. When accelerating again,itis
necessary toshift uptothe desired
range.
. When theCVT fluidtemperature isextre-
mely low,the manual shiftmode maynot
work andautomatically shiftasadrive mode.
This isnot amalfunction. Inthis case, return
the shift lever tothe D(Drive) position and
drive forawhile andthen shifttothe manual
shift mode.
. When theCVT fluidtemperature ishigh, the
shift range mayupshift atalower engine
speed thanusual. Thisisnot amalfunction.
Accelerator downshiftÐInDposition Ð
GUID-BF3E0 6A6-2637-42C1-966D-5E 30031CA744
For passing orhill climbing, fullydepress the
accelerator pedaltothe floor. Thisshifts the
transmission downintoalower gear,depending
on the vehicle speed.
High fluidtemperature protectionmode
GUID-CE86 9FBC-89CE -4D62-AEC8 -660F5235AF 18
This transmission hasahigh fluidtemperature
protection mode.Ifthe fluid temperature be-
comes toohigh (forexample, whenclimbing
steep grades inhigh temperature withheavy
loads) ,engine powerand,under somecondi-
tions, vehicle speedwillbedecreased auto-
matically toreduce thechance oftransmission
damage. Vehicle speed canbecontrolled with
the accelerator pedal,buttheengine andvehicle
speed maybelimited.
Fail-safe
GUID-EA 910347-92 E1-44D4-92 56-120D487E42CA
If the vehicle isdriven underextreme
conditions, suchasexcessive wheelspin-
ning andsubsequent hardbraking, the
fail-safe systemmaybeactivated. TheMIL
may illuminate toindicate thefail-safe
mode isactivated. (SeeªMalfunction In-
dicator Light(MIL)º (P.2-18) .)This will
occur evenifall electrical circuitsare
functioning properly.Inthis case, place
the ignition switchinthe OFF position and
wait for10seconds. Thenturntheswitch
Starting anddriving
5-17
& R Q G L W L R Q
Page 262 of 383
> ( G L W 0 R G H O ) ' @
5-18
Starting anddriving
back tothe ONposition. Thevehicle
should returntoits normal operating
condition. Ifitdoes notreturn toits normal
operating condition, haveaNISSAN dealer
check thetransmission andrepair ifne-
cessary.
WARNING
When thehigh fluid temperature pro-
tection modeorfail-safe operation
occurs, vehiclespeedmaybegradually
reduced. Thereduced speedmaybe
lower thanother traffic,which could
increase thechance ofacollision. Be
especially carefulwhendriving. Ifne-
cessary, pulltothe side ofthe road ata
safe place andallow thetransmission
to return tonormal operation, orhave it
repaired if
necessary.
SSD1142
Shift lockrelease
GUID-39E4 740A-3513-44A0-A3 06-744DB1802606
If the battery charge islow ordischarged, the
shift lever maynotbemoved fromtheP(Park)
position evenwiththebrake pedal depressed
and theshift lever button pushed.
T o move theshift lever, perform thefollowing
procedure:
1. Place theignition switchinthe OFF or
L OCK position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover
*
A
using asuitable tool. 4.
Push down theshift lockrelease usinga
suitable tool.
5. Push theshift lever button andmove the
shift lever tothe N(Neutral) positionwhile
holding downtheshift lockrelease.
Place theignition switchinthe ON position. The
vehicle maybemoved tothe desired location.
Replace theremoved shiftlockrelease cover
after theoperation.
If the battery isdischarged completely,the
steering wheelcannot beunlocked. Donot
move thevehicle withthesteering wheellocked.
If the shift lever cannot bemoved outofthe P
(Park) position, haveaNISSAN dealercheckthe
CVT system assoon aspossible.
WARNING
If the shift lever cannot bemoved from
the P(Park) position whiletheengine is
running andthebrake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause
an accident injuringyourself and
others.
& R Q G L W L R Q
Page 263 of 383
> ( G L W 0 R G H O ) ' @
MANUAL TRANSMISSIO N(MT)
GUID-578 CD4B7-85A6 -49CB-AB4F-F226DA21 98CA
WARNING
. Do not downshift abruptlyonslip-
pery roads. Thismay cause aloss of
control.
. Do not over-rev theengine when
shifting toalower gear.Thismay
cause aloss ofcontrol orengine
damage.
. When thehigh fluid temperature
protection modeorfail-safe opera-
tion occurs, vehiclespeedmaybe
gradually reduced.Thereduced
speed maybelower thanother
traffic ,which couldincrease the
chance ofacollision. Beespecially
careful whendriving. Ifnecessary,
pull tothe side ofthe road atasafe
place andallow thetransmission to
return tonormal operation, orhave
it repaired ifnecessary.
CAUTION
. Do not rest your footonthe clutch
pedal whiledriving. Thismay da-
mage theclutch.
. Fully depress theclutch pedalbe-
fore shifting tohelp prevent trans-
mission damage.
. Stop yourvehicle completely before
shifting intoR(Reverse) .
. When thevehicle isstopped fora
period oftime, forexample atastop
light, shifttoN(Neutral) andrelease
the clutch pedalwiththefoot brake
applied.
SSD0552
Shifting
GUID-9FDDD F2D-B4D7-4E6E-B1E 7-9D36A148 D03F
T o change gears,orwhen upshifting ordown-
shifting, fullydepress theclutch pedal, shiftinto
the appropriate gear,thenslowly andsmoothly
release theclutch pedal.
T o ensure smooth gearchanges, besure tofully
depress theclutch pedalbefore operating the
shift lever. Ifthe clutch pedalisnot fully
depressed beforethetransmission isshifted, a
gear noise maybeheard. Transmission damage
could occur.
Start thevehicle in1st gear andshift to2nd,
3rd, 4th,5thand 6thgear insequence accord-
ing tovehicle speed.
Starting anddriving
5-19
& R Q G L W L R Q
Page 264 of 383
> ( G L W 0 R G H O ) ' @
5-20
Starting anddriving
T o back up,pull theshift lever ring
*
1
upward
and then move itto the R(Reverse) gearafter
stopping thevehicle completely .
The shift lever ringreturns toits original position
when theshift lever ismoved tothe N(Neutral)
position.
If itis difficult tomove theshift lever intotheR
(Reverse) or1st gear, shifttothe N(Neutral)
position, andthen release theclutch pedalonce.
Fully depress theclutch pedalagainandshift
into theR(Reverse) or1st gear.
Suggested upshiftspeeds
GUID-24C1 C741-C5AB -4388-A7C4-8E56E96 33140
The following aresuggested vehiclespeeds for
shifting intoahigher gear.These suggestions
relate tofuel economy andvehicle performance.
Actual upshift speeds willvary according toroad
conditions, theweather andindividual driving
habits.
Gear change MPH
(km/h)
1st to2nd 13
(21)
2nd to3rd 22
(35)
3rd to4th 30
(48)
4th to5th 35
(56)
5th to6th 42
(68)
Suggested maximumspeedineach gear
GUID-BE B03AA8-9FB 8-4719-8FC9-F9ABBD368399
Downshift toalower gearifthe engine isnot
running smoothly ,or ifyou need toaccelerate.
Do not exceed themaximum suggested speed
(shown below)inany gear. Forlevel road
driving, usethehighest gearsuggested forthat
speed. Always observe postedspeedlimits,and
drive according tothe road conditions, which
will ensure safeoperation. Donot over-rev the
engine whenshifting toalower gearasitmay
cause engine damage orloss ofvehicle control.
Except forNISMO RSmodels:
Gear MPH
(km/h)
1st 31
(50)
2nd 55
(88)
3rd 76
(122)
4th Ð
5th Ð
6th Ð
For NISMO RSmodels:
Gear MPH
(km/h)
1st 27
(44)
2nd 50
(80)
3rd 73
(118)
4th Ð
5th Ð
6th Ð
& R Q G L W L R Q
Page 266 of 383
> ( G L W 0 R G H O ) ' @
5-22
Starting anddriving
SSD1144
Example
Three drivemodes (NORMAL, SPORTand
ECO) canbeselected depending onthe driving
condition. Wheneachmode isselected, the
control stateofthe engine, CVT(ifso
equipped) ,steering andclimate appears on
the display briefly.
Each selected Drivemode (NORMAL, SPORT
or ECO) isdisplayed atthe top ofthe display
screen.
NO TE:
. The display valuesoftorque, boostand
current fueleconomy maydiffer de-
pending ondriving conditions. Usethe
display valuesasreference only. .
The vehicle willbeset tothe NORMAL
drive mode whenrestarting the engine.
SSD1145
NORMAL drivemode
GUID-671 4E0F5-DB61 -4CAD-BB14- F2E233E040A 2
The NORMAL drivemode isrecommended for
normal driving. To set the NORMAL drivemode,
press theDrive mode select button andthen
press theNORMAL drivemode button. The
control stateofthe engine, CVT(ifso equipped)
steering andclimate isdisplayed briefly.
When theNORMAL drivemode isselected, a
voltage meterandanengine torquemeter
appear onthe display screen.
NO TE:
. The voltage metermaychange accord-
ing tothe driving condition. Thisisnot
a malfunction.
& R Q G L W L R Q
Page 267 of 383
> ( G L W 0 R G H O ) ' @
. Atstart up,the vehicle isautomatically
set tothe NORMAL drive
mode.
SSD1146
SPORT drivemode
GUID-0A6 211E0-42EC -41E4-8E12-C8C5047006 D5
The SPORT drivemode isrecommended foran
enhanced performance feel.To set the SPORT
drive mode, pressthedrive mode select button.
The control stateofthe engine, CVT(ifso
equipped) ,steering andclimate controlis
displayed briefly.In the SPORT mode,the
engine, CVT(ifso equipped) andsteering are
set toSPORT .Climate controlisset to
NORMAL.
When theSPORT drivemode isselected, a
boost meter appears onthe display screen. NO
TE:
In the SPORT mode,fueleconomy maybe
reduced.
Starting anddriving
5-23
& R Q G L W L R Q