start stop button NISSAN JUKE 2015 F15 / 1.G Owners Manual


> (GLW   0RGHO )'@
2-30
Instrument sand controls
SIC2045
How toarm thevehicle security system
GUID-0B0D5 4E3-2D2E-4E66-84C2-DB 089A802C9C
1. Close allwindows.
The system canbearmed evenifthe
windows areopen.
2. Place theignition switchinthe OFF position
and remove theIntelligent Key from the
vehicle.
3. Close alldoors. Lockalldoors. Thedoors
can belocked with:
.
the L OCK
button onthe Intelligent
K ey
.
any request switch
.
the power doorlockswitch
.
the mechanical key
4. Confirm thatthesecurity indicator light
illuminates. Thesecurity indicator lightstays
on for about 30seconds. Thevehicle
security systemisnow pre-armed. After
about 30seconds thevehicle security
system automatically shiftsintothearmed
phase. Thesecurity lightbegins toflash
once every approximately 3seconds. If,
during this30-second pre-armtimeperiod,
the door isunlocked, orthe ignition switchis
placed inthe ACC orON position, the
system willnotarm.
Even when thedriver and/or passengers
are inthe vehicle, thesystem willactivate
with alldoors locked withtheignition
switch inthe LOCK position. Whenplacing
the ignition switchinthe ACC orON
position, thesystem willbereleased.
V ehicle security systemactivation
GUID-586 0D76E-23D 8-4381-99F0 -0DD8252DADA1
The vehicle security systemwillgive thefollow-
ing alarm:
. The headlights blinkandthehorn sounds
intermittently .
. The alarm automatically turnsoffafter
approximately 50seconds. However, the
alarm reactivates ifthe vehicle istampered
with again. The
alarm isactivated by:
. Unlocking thedoor without usingthe
Intelligent Key ,the request switchorthe
key .(Even ifthe door isopened byreleasing
the door inside lockknob, thealarm will
activate.)
How tostop anactivated alarm
GUID-C58 BB668-0D8A- 41CA-8C30-D900891AB B1A
The alarm willstop byunlocking adoor by
pushing theUNL
OCK
button onthe
Intelligent Key ,pushing therequest switchor
using thekey.The alarm willnotstop ifthe
ignition switchisplaced inthe ACC orON
position.
If the system doesnotoperate asde-
scribed above,haveitchecked bya
NISSAN dealer.
NISSAN VEHICLE IMMOBILIZE RSYS-
TEM
GUID-82475E C2-840C-467B-A31D-9 7F570513B2F
The NISSAN Vehicle Immobilizer Systemwillnot
allow theengine tostart without theuse ofthe
registered key.
If the engine failstostart using theregistered
key ,it may bedue tointerference causedby
another registered key,an automated tollroad
device orautomated paymentdeviceonthe key
ring. Restart theengine usingthefollowing
procedures:
&RQGLWLRQ


> (GLW   0RGHO )'@
TROUBLESH OOTING GUIDE
GUID-FD 003181-72 3A-472E-84F 6-40154676082B
Symptom Possible cause Action
totake
When pushing theignition switch
to stop theengine The
Pposition selecting warninglightinthe
meter illuminates andtheinside warning chime
sounds continuously (Continuously Variable
T ransmission models). The
shift lever isnot inthe P(Park)
position. Shift
theshift lever tothe P(Park) position.
When shifting theshift lever tothe
P (Park) position. The
inside warning chimesounds continuously
(Continuously Variable Transmission models).The
ignition switchisin the ACC orON
position. Push
theignition switchtothe OFF posi-
tion.
When opening thedriver's door
to get outofthe vehicle The
inside warning chimesounds continuously .The
ignition switchisin the ACC
position. Push
theignition switchtothe OFF posi-
tion.
When closing thedoor afterget-
ting outofthe vehicle The
Intelligent Key system warning lightinthe
meter blinks inyellow ,and theoutside chime
sounds 3times andtheinside warning chime
sounds forafew seconds. The
ignition switchisin the ACC orON
position. Push
theignition switchtothe OFF posi-
tion.
The Pposition selecting warninglightinthe
meter illuminates andtheoutside chime
sounds continuously (Continuously Variable
T ransmission models). The
ignition switchisin the ACC orOFF
position andtheshift lever isnot inthe P
(Park) position. Move
theshift lever tothe P(Park) position
and push theignition switchtothe OFF
position.
When closing thedoor withthe
inside lockknob turned toLOCK The
outside chimesounds forafew seconds
and allthe doors unlock. The
Intelligent Key isinside thevehicle. Carry
theIntelligent Key with you.
When pushing therequest switch
or the LOCK
button onthe
Intelligent Key tolock thedoor The
outside chimesounds forafew seconds. The
Intelligent Key isinside thevehicle. Carry
theIntelligent Key with you.
A door isnot closed securely . Close
thedoor securely .
When pushing theignition switch
to start theengine The
Intelligent Key system warning lightinthe
meter blinks ingreen. The
battery charge islow . Replace
thebattery withanew one. (See
ªIntelligent Key battery replacementº (P.8-
23) .)
The Intelligent Key system warning lightinthe
meter blinks inyellow andtheinside warning
chime sounds forafew seconds. The
Intelligent Key isnot inthe vehicle. Carry
theIntelligent Key with you.
When pushing theignition switch The
Intelligent Key system warning lightinthe
meter illuminates inyellow . It
warns ofamalfunction withthe
Intelligent Key system. Contact
aNISSAN dealer.
Pre-d riving checks andadjustments
3-11
&RQGLWLRQ


> (GLW   0RGHO )'@
4-44
Heater, airconditione r,audio andphone systems
FM-AM Radiooperation
GUID-F6 D3CBA1-CE 19-4A9D-8F43-C15C7 32220C2
radio (FM´AM) bandselect :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Push the
button tochange theband as
follows:
AM ?FM1 ?FM2? AM
TUNE (Tuning) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
T urn theTUNE´FOLDER knobformanual tuning.
SEEK tuning:
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Push the
or
button totune from lowto
high orhigh tolow frequencies andtostop at
the next broadcasting station.
SCAN tuning:
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Push the
button totune from lowtohigh
frequencies andstop ateach broadcasting
station forseveral seconds. Pushingthebutton
again during thisseveral seconds periodwill
stop SCAN tuningandtheradio willremain
tuned tothat station.
If the
button isnot pushed withinthis
period, SCANtuningmoves tothe next
station.
to
Radio memory buttons:
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Up to12 stations canbeset forthe FM band (6
each forFM1 andFM2) and6stations canbe
set forthe AM band. 1.
Choose theradio band using the
button.
2. Tune tothe desired station.
3. Push andhold thedesired stationpreset
button
to
until beep sounds.
4. The station indicator willthen come on.The
station isnow settothe button memory .
5. Other buttons canbeset inthe same
manner.
If the battery cableisdisconnected, orifthe fuse
opens, thestation memory willbeerased. Inthat
case, resetthedesired stations.
CD player operation
GUID-248 E139A-04E4 -4AD2-8E33-2281B71D 316A
Place theignition switchinthe ON orACC
position. InserttheCompact Disc(CD) intothe
slot with thelabel sidefacing up.The CDwillbe
guided automatically intotheslot and start
playing.
After loading theCD, thenumber oftracks on
the CD and theplay time willappear onthe
display .
If another audiosource isalready operating, it
will automatically turnoffand theCD willplay.
If the system hasbeen turned offwhile theCD
was playing, pushing thePower button willstart
the CD.
CD PLA Y:
GUID-F 83C168B-173D -4313-B631-F712588C04 63
When theCD button ispushed whileaCD is
loaded, theCD willstart playing.
SEEK TRACK:
GUID-F 83C168B-173D -4313-B631-F712588C04 63
When the
or
button ispushed andhold
while theCD isbeing played, theCD willplay
while fastforwarding orrewinding. Whenthe
button isreleased, theCD willreturn tonormal
play speed.
When the
or
button ispushed while
the CD isbeing played, thenext track orthe
beginning ofthe current trackonthe CD willbe
played.
REPEA T(RPT) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
When theRPT button ispushed whiletheCD is
played, theplay pattern canbechanged as
follows:
(CD)
(Normal) Û1Track Repeat
(CD withcompressed audiofiles)
(Normal) ?1Folder Repeat ?1Track Repeat
? (Normal)
RANDOM (RDM):
GUID-F 83C168B-173D -4313-B631-F712588C04 63
When theRDM button ispushed whileaCD is
&RQGLWLRQ


> (GLW   0RGHO )'@
passenger car.The vehicle isnot
designed forcornering atthe same
speeds asconventional passenger
cars. Failure tooperate thisvehicle
correctly couldresult inloss of
control and/orarollover accident.
. Always usetires ofthe same type,
size, brand, construction (bias,bias-
belted orradial) ,and tread pattern
on allfour wheels. Installtraction
devices onthe front wheels when
driving onslippery roadsanddrive
carefully.
. Besure tocheck thebrakes imme-
diately afterdriving inmud orwater.
See ªBrake systemº (P.5-35) forwet
brakes.
. Avoid parking yourvehicle onsteep
hills. Ifyou getout ofthe vehicle
and itrolls forward, backward or
sideways, youcould beinjured.
. Whenever youdrive off-road
through sand,mudorwater asdeep
as the wheel hub,more frequent
maintenance mayberequired. See
the maintenance informationinthe
ªNISSAN ServiceandMaintenance
Guideº . .
Spinning thefront wheels onslip-
pery surfaces maycause theAWD
warning lighttoflash andtheAWD
system toautomatically switchfrom
the AWD mode tothe 2WD mode.
This could reduce traction. Beespe-
cially careful whentowing atrailer
(AWD model) .
GUID-A A9BA26A-B 49B-43B0-A908-85126 20A8F65
WARNING
Do not operate thepush-button ignition
switch whiledriving thevehicle except
in an emergency. (Theengine willstop
when theignition switchispushed 3
consecutive timesorthe ignition switch
is pushed andheld formore than2
seconds.) Ifthe engine stopswhilethe
vehicle isbeing driven, thiscould lead
to acrash andserious injury.
Before operating thepush-button ignition
switch, besure tomove theshift lever tothe P
(Park) position (forContinuously Variable Trans-
mission models) orthe shift lever tothe N
(Neutral) position(formanual transmission
models) .
Starting anddriving
5-9
PUSH-BUT TON IGNITION SWITCH
&RQGLWLRQ


> (GLW   0RGHO )'@
GUID-74 08FE11-64BC -4759-BC8E-07366732C0C9
1. Apply theparking brake.
2. Move theshift lever tothe P(Park) orN
(Neutral) position.(Pisrecommended.)
The starter isdesigned nottooperate unless
the shift lever isin either ofthe above
positions.
Manual Transmission (MT)models:
Move theshift lever tothe N(Neutral)
position. Depresstheclutch pedalfullyto
the floor.
The starter isdesigned nottooperate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried
when operating theignition switch.
3. Push theignition switchtothe ON position.
Depress thebrake pedal(CVTmodels) or
the clutch pedal(MTmodels) andpush the
ignition switchtostart theengine.
T o start theengine immediately ,push and
release theignition switchwhiledepressing
the brake pedal withtheignition switchin
any position.
.
If the engine isvery hard tostart in
extremely coldweather orwhen restart-
ing, depress theaccelerator pedalalittle
(approximately 1/3tothe floor) andwhile
holding, cranktheengine. Release the
accelerator pedalwhentheengine starts.
.
If the engine isvery hard tostart because
it is flooded, depresstheaccelerator
pedal allthe way tothe floor andhold it.
Push theignition switchtothe ON
position tostart cranking theengine.
After 5or 6seconds, stopcranking by
pushing theignition switchtoOFF .After
cranking theengine, releasetheaccel-
erator pedal. Cranktheengine withyour
foot offthe accelerator pedalby
depressing thebrake pedal andpushing
the push-button ignitionswitchtostart
the engine. Ifthe engine starts,butfails
to run, repeat theabove procedure.
CAUTION
Do not operate thestarter formore
than 15seconds atatime. Ifthe engine
does notstart, pushtheignition switch
to OFF andwait 10seconds before
cranking again,otherwise thestarter
could bedamaged.
4. Warm-up
Allow theengine toidle foratleast 30
seconds afterstarting. Donot race the
engine whilewarming itup. Drive at
moderate speedforashort distance first, especially
incold weather. Incold weather,
keep theengine running foraminimum of2-
3 minutes beforeshutting itoff. Starting and
stopping theengine overashort period of
time maymake thevehicle moredifficult to
start.
When racing theengine upto4,000 rpmor
more under noload condition, theengine
will enter thefuel cutmode.
5. To stop theengine, movetheshift lever to
the P(Park) position (CVTmodels) ormove
the shift lever tothe N(Neutral) position(MT
models) ,and push theignition switchtothe
OFF position.
NO TE:
Care should betaken toavoid situations
that canlead topotential batterydischarge
and potential no-startconditions suchas:
1. Installation orextended useofelectro-
nic accessories thatconsume battery
power whentheengine isnot running
(Phone chargers, GPS,DVDplayers,
etc .)
2. Vehicle isnot driven regularly and/or
only driven shortdistances.
In these cases, thebattery mayneed tobe
charged tomaintain batteryhealth.
Starting anddriving
5-13
ST ARTING THEENGINE
&RQGLWLRQ


> (GLW   0RGHO )'@
5-14
Starting anddriving
GUID-00 99E665-725B -489E-B596-F5A3F4CD54DB
CONTINUOUS LY VARIABLE TRANS-
MISSION (CVT)
GUID-C69 9DF0B-987D -4AD2-879E-728294 24A200
The Continuously Variable Transmission (CVT)
in your vehicle iselectronically controlledto
produce maximum powerandsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.
Follow theseprocedures formaximum vehicle
performance anddriving enjoyment.
Engine powermaybeautomatically re-
duced toprotect theCVT ifthe engine
speed increases quicklywhendriving on
slippery roadsorwhile being tested on
some dynamometers.
Starting thevehicle
GUID-5D2 73D53-F49E -430A-9675-C A17371F1DFA
1. After starting theengine, fullydepress the
foot brake pedalbefore moving theshift
lever outofthe P(Park) position.
This CVTisdesigned sothat thefoot
brake pedalmustbedepressed before
shifting fromP(Park) toany driving
position whiletheignition switchisin
the ONposition.
The shift lever cannot bemoved outof
the P(Park) position andinto anyof
the other positions ifthe ignition
switch isplaced inthe LOCK ,OFF or
ACC position orifthe key isremoved. 2.
Keep thefoot brake pedaldepressed, push
the shift lever button andmove theshift lever
to adriving position.
3. Release theparking brakeandfoot brake
pedal, andthen gradually startthevehicle in
motion.
WARNING
. Do not depress theaccelerator
pedal whileshifting fromP(Park)
or N(Neutral) toR(Reverse) ,D
(Drive) ,or manual shiftmode (ifso
equipped) .Always depress the
brake pedaluntilshifting iscom-
pleted. Failure todo socould cause
you tolose control andhave an
accident.
. Cold engine idlespeed ishigh, so
use caution whenshifting intoa
forward orreverse gearbefore the
engine haswarmed up.
. Never shifttoP(Park) orR(Re-
verse) whilevehicle ismoving. Fail-
ure todo socould cause youtolose
control andhave anaccident.
CAUTION
. Except inan emergency, donot shift
to the N(Neutral) positionwhile
driving. Coasting withthetransmis-
sion inthe N(Neutral) positionmay
cause serious damage tothe trans-
mission.
. When stopping thevehicle onan
uphill grade, donot hold thevehicle
by depressing theaccelerator pedal.
The foot brake should beused for
this purpose.
. Do not downshift abruptlyonslip-
pery roads. Thismay cause aloss of
control.
DRIVING THEVEHICLE
&RQGLWLRQ


> (GLW   0RGHO )'@
SSD1140
T o move theshift lever,
: Push
thebutton
*
A
while depressing the
brake
pedal.
: Push
thebutton
*
A
.
: Just
move theshift lever.
Shifting
GUID-8E3 3D228-CFD 5-4E80-8A5F -A2EC598FE23A
After starting theengine, fullydepress thebrake
pedal, pushtheshift lever button andmove the
shift lever fromtheP(Park) position toany ofthe
desired shiftpositions.
WARNING
Apply theparking brakeifthe shift lever
is in any position whiletheengine is
not running. Failuretodo socould
cause thevehicle tomove unexpectedly
or roll away andresult inserious
personal injuryorproperty damage.
If the ignition switchisplaced inthe OFF or
ACC position forany reason whiletheshift lever
is in any positions otherthantheP(Park) ,the
ignition switchcannot beplaced inthe LOCK
position.
If the ignition switchcannot beplaced inthe
L OCK position, performthefollowing steps:
1. Apply theparking brakewhenthevehicle is
stopped.
2. Place theignition switchinthe ON position
while depressing thefoot brake pedal.
3. Move theshift lever tothe P(Park) position.
4. Place theignition switchinthe OFF position.
CAUTION
T o prevent transmission damage,move
the shift lever tothe P(Park) orR
(Reverse) positiononlywhen thevehi-
cle iscompletely stopped.
P (Park) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition whenthevehicle isparked or
when starting theengine. Makesurethevehicle
is completely stopped.Thebrake pedalmust
be depressed andtheshift lever button
pushed into move theshift lever fromN
(Neutral) orany drive position toP(Park) .
Apply theparking brake.Whenparking onahill,
apply theparking brakefirst,then move theshift
lever tothe P(Park) position.
R (Reverse) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Use thisposition toback up.Make surethe
vehicle iscompletely stoppedbeforeselecting
the R(Reverse) position.Thebrake pedal
must bedepressed andtheshift lever
button pushed into move theshift lever
from P(Park) ,N (Neutral) orany driving
position toR(Reverse) .
N (Neutral) :
GUID-F 83C168B-173D -4313-B631-F712588C04 63
Neither forward norreverse gearisengaged.
Starting anddriving
5-15
&RQGLWLRQ


> (GLW   0RGHO )'@
5-18
Starting anddriving
back tothe ONposition. Thevehicle
should returntoits normal operating
condition. Ifitdoes notreturn toits normal
operating condition, haveaNISSAN dealer
check thetransmission andrepair ifne-
cessary.
WARNING
When thehigh fluid temperature pro-
tection modeorfail-safe operation
occurs, vehiclespeedmaybegradually
reduced. Thereduced speedmaybe
lower thanother traffic,which could
increase thechance ofacollision. Be
especially carefulwhendriving. Ifne-
cessary, pulltothe side ofthe road ata
safe place andallow thetransmission
to return tonormal operation, orhave it
repaired if
necessary.
SSD1142
Shift lockrelease
GUID-39E4 740A-3513-44A0-A3 06-744DB1802606
If the battery charge islow ordischarged, the
shift lever maynotbemoved fromtheP(Park)
position evenwiththebrake pedal depressed
and theshift lever button pushed.
T o move theshift lever, perform thefollowing
procedure:
1. Place theignition switchinthe OFF or
L OCK position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover
*
A
using asuitable tool. 4.
Push down theshift lockrelease usinga
suitable tool.
5. Push theshift lever button andmove the
shift lever tothe N(Neutral) positionwhile
holding downtheshift lockrelease.
Place theignition switchinthe ON position. The
vehicle maybemoved tothe desired location.
Replace theremoved shiftlockrelease cover
after theoperation.
If the battery isdischarged completely,the
steering wheelcannot beunlocked. Donot
move thevehicle withthesteering wheellocked.
If the shift lever cannot bemoved outofthe P
(Park) position, haveaNISSAN dealercheckthe
CVT system assoon aspossible.
WARNING
If the shift lever cannot bemoved from
the P(Park) position whiletheengine is
running andthebrake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause
an accident injuringyourself and
others.
&RQGLWLRQ