ignition NISSAN JUKE 2016 F15 / 1.G Owner's Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: JUKE, Model: NISSAN JUKE 2016 F15 / 1.GPages: 399, PDF Size: 3.36 MB
Page 112 of 399
> ( G L W 0 R G H O ) ' @
2-36Instruments and controls
Pulling up the wiper arm:
The windshield wipers must be in the service
position in order to replace the wiper blades.
To move the wiper blades to the service position,
follow this procedure:
.When the ignition switch is in the ªONº
position or within 60 seconds of placing the
ignition switch to the ªOFFº position, lift the
lever up
*4two times in less than 0.5
seconds. The windshield wipers will move to
the service position automatically, and the
wiper blades can now be replaced. To
replace the wiper blades, see ªWindshield
wiper bladesº (P.8-18).
To move the wiper blades back to the original
position:
. Lift the lever up
*4or push the lever down
to operate at any wiper speed.
CAUTION
. This function can be operated even
if the ignition switch is in the ªONº
position. However, to prevent an
accident or damage when pulling
up the wiper arm, be sure to observe
the following precautions. Ð Make sure the shift lever is in
the P (Park) position (Continu-
ously Variable Transmission
models) .
Ð Make sure the shift lever is in the N (Neutral) position, with the
parking brake fully applied
(Manual Transmission models) .
Ð Never allow the passengers to operate the windshield wiper
switch inadvertently.
. Do not operate the windshield wiper
while the wiper arm is pulled up. The
wiper arm may be damaged.
GUID-0013655D-0D88-4D9F-87AB-B359910F5671
WARNING
In freezing temperatures the washer
solution may freeze on the rear window
glass and obscure your vision. Warm
the rear window with the defroster
before you wash the rear window.
CAUTION
.Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength. Some
methyl alcohol based washer fluid
concentrates may permanently stain
the grille if spilled while filling the
window washer reservoir tank.
. Pre-mix washer fluid concentrates
with water to the manufacturer's
recommended levels before pouring
the fluid into the window washer
reservoir tank. Do not use the
REAR WINDOW WIPER AND
WASHER SWITCH
& R Q G L W L R Q
Page 113 of 399
> ( G L W 0 R G H O ) ' @
window washer reservoir tank to
mix the washer fluid concentrate
and water.
If the rear window wiper operation is
interrupted by snow or ice, the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to the OFF
position and remove the snow or ice that is
on and around the wiper arms. In approxi-
mately 1 minute, turn the switch on again
to operate the wiper.
SIC3666
The rear window wiper and washer operate
when the ignition switch is in the ON position.
Turn the switch clockwise from the OFF position
to operate the wiper.
*1Intermittent (INT) Ð intermittent operation (not
adjustable)
*2Low (ON) Ð continuous low speed operation
Push the switch forward*3to operate the
washer. Then the wiper will also operate several
times.
GUID-A6ACEC3D-569F-4102-A2B6-4DE76F74F79B
SIC4520
Type A (if so equipped)
SIC4519
Type B (if so equipped)
Instruments and controls2-37
REAR WINDOW AND OUTSIDE
MIRROR DEFROSTER SWITCH
& R Q G L W L R Q
Page 115 of 399
> ( G L W 0 R G H O ) ' @
SIC3668
HEADLIGHT SWITCHGUID-78F7386F-88AF-48CA-8EC4-39D87DBFEDF9
LightingGUID-C7E4F4F1-DC4D-4024-8FF6-AC24A3D2B1F5*1Turn the switch to theposition:
The front parking, side marker, tail, license plate,
instrument lights will come on. However, the
daytime running light (for NISMO models and
Canada) will turn off.
*2Turn the switch to theposition:
Headlights will come on and all the other lights
remain on. However, the daytime running light
(for NISMO models and Canada) will turn off.
SIC3669
Autolight system (if so equipped)GUID-2F769165-6329-45F4-95DB-2F94DB2FE66CThe autolight system allows the headlights to be
set so they turn on and off automatically.
To set the autolight system:
1. Make sure the headlight switch is in the AUTO position
*1.
2. Place the ignition switch in the ON position.
3. The autolight system automatically turns the headlights on and off.
To turn the autolight system off, turn the switch
to the OFF,
orposition.
The autolight system can turn on the headlights
automatically when it is dark and turn off the headlights when it is light.
The headlights will also be turned on automa-
tically at twilight or in rainy weather (when the
windshield wiper is operated continuously) .
If the ignition switch is placed in the OFF
position and one of the doors is opened and this
condition is continued, the headlights remain on
for 5 minutes.
Instruments and controls2-39
& R Q G L W L R Q
Page 116 of 399
> ( G L W 0 R G H O ) ' @
2-40Instruments and controls
SAA1232
Be sure not to put anything on top of the
photo sensor
*1located on the top of the
instrument panel. The photo sensor con-
trols the autolight; if it is covered, the
photo sensor reacts as if it is dark and the
headlights will illuminate.
Automatic headlights off delayGUID-CFAAEF09-71A1-4057-9F7B-96D46980C786You can keep the headlights on for up to 45
seconds after you place the ignition switch in the
OFF position and open any door then close all
the doors.
SIC3670
Headlight beam selectGUID-65D36B20-DAE3-4840-AD10-0068CB054884*1To select the low beam, put the lever in the
neutral position as shown.
*2To select the high beam, push the lever forward
while the switch is in theposition. Pull it
back to select the low beam.
*3Pulling the lever toward you will flash the
headlight high beam even when the headlight
switch is in the OFF position.
Battery saver systemGUID-E8409034-D45E-48DE-A071-E3A41898289B. When the headlight switch is in theor
position while the ignition switch is in
the ON position, the lights will automatically
turn off within a period of time after the
ignition switch has been placed in the OFF
position.
. When the headlight switch remains in the
orposition after the lights auto-
matically turn off, the lights will turn on when
the ignition switch is placed in the ON
position.
CAUTION
. When you turn on the headlight
switch again after the lights auto-
matically turn off, the lights will not
turn off automatically. Be sure to
turn the light switch to the OFF
position when you leave the vehicle
for extended periods of time, other-
wise the battery will be discharged.
. Never leave the light switch on
when the engine is not running for
extended periods of time even if the
headlights turn off automatically.
& R Q G L W L R Q
Page 117 of 399
> ( G L W 0 R G H O ) ' @
Daytime running light system (for NISMO
models and Canada)
GUID-62FCD516-90BE-43E6-ACAB-5CD8364D8567The daytime running lights automatically illumi-
nate when the engine is started with the parking
brake released. The daytime running lights
operate with the headlight switch in the OFF
position. Turn the headlight switch to the
position for full illumination when driving at night.
(The daytime running lights will turn off.)
If the parking brake is applied before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illuminate
once the parking brake is released. The daytime
running lights will remain on until the ignition
switch is placed in the OFF position.
WARNING
When the daytime running light system
is active, tail lights on your vehicle are
not on. It is necessary at dusk to turn on
your headlights. Failure to do so could
cause an accident injuring yourself and
others.
JVI1342X
Type A (if so equipped)
JVI1343X
Type A (if so equipped)
SIC4517
Type B (if so equipped)
SIC4129
Type B (if so equipped)
Instruments and controls2-41
& R Q G L W L R Q
Page 118 of 399
> ( G L W 0 R G H O ) ' @
2-42Instruments and controls
Instrument brightness controlGUID-955DB8AF-41FD-4C7B-B17D-A344031AD5BBThe instrument brightness control operates
when the ignition switch is in the ON position.
Push the control knob
*Ato adjust the bright-
ness of the instrument panel lights. The bright-
ness indicator
*Bwill be shown briefly in the
vehicle information display when the control is
turned.
When the brightness level reaches the maximum
or minimum, a beep will sound.
SIC3671
TURN SIGNAL SWITCHGUID-DF12F6F8-A1D7-4024-A4DF-46D972E49E9C
*1Turn signalGUID-3CF2F736-4960-4B96-B5CF-1271A559F90AMove the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
*2Lane change signalGUID-BCAE5264-DA08-4A37-B0F2-FDE7D90FCC8FMove the lever up or down until the turn signal
begins to flash, but the lever does not latch, to
signal a lane change. Hold the lever until the lane
change is completed.
Move the lever up or down until the turn signal
begins to flash, but the lever does not latch, and
release the lever. The turn signal will automati-
cally flash three times. Choose the appropriate method to signal a lane
change based on road and traffic conditions.
& R Q G L W L R Q
Page 125 of 399
> ( G L W 0 R G H O ) ' @
GUID-ECC58B2D-F250-41F5-B8E8-7EBD4B79C5CAPOWER WINDOWSGUID-6A23709F-5277-4229-B1AD-2B7DC859B673
WARNING
.Make sure that all passengers have
their hands, etc. inside the vehicle
while it is in motion and before
closing the windows. Use the win-
dow lock switch to prevent unex-
pected use of the power windows.
. To help avoid risk of injury or death
through unintended operation of
the vehicle and or its systems,
including entrapment in windows
or inadvertent door lock activation,
do not leave children, people who
require the assistance of others or
pets unattended in your vehicle.
Additionally, the temperature inside
a closed vehicle on a warm day can
quickly become high enough to
cause a significant risk of injury or
death to people and pets.
The power windows operate when the ignition
switch is in the ON position, or for about 45
seconds after the ignition switch is placed in the
OFF position. If the driver's or front passenger's
door is opened during this period of about 45 seconds, power to the windows is canceled.
SIC4533
1. Window lock button
2. Driver side window
3. Rear left passenger side window
4. Front passenger side window
5. Rear right passenger side window
Main power window switch (driver's
side)
GUID-F0D006F2-BA97-4BA8-9004-BA0E645371B0To open or close the window, push down*Aor
pull up
*Bthe switch and hold it. The main
switch (driver side switches) will open or close
all the windows.
Instruments and controls2-49
WINDOWS
& R Q G L W L R Q
Page 127 of 399
> ( G L W 0 R G H O ) ' @
Auto-reverse functionGUID-C5187523-35D8-44E8-9700-CA4CAB34864E
WARNING
There are some small distances imme-
diately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., in-
side the vehicle before closing the
window.
If the control unit detects something caught in
the window as it is closing, the window will be
immediately lowered.
The auto reverse function can be activated when
the window is closed by automatic operation
when the ignition switch is in the ON position or
for 45 seconds after the ignition switch is placed
in the OFF position.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the window
occurs.
If the windows do not close automaticallyGUID-B6340D93-45A3-48B4-BE8B-20DD3A8E0867If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system.
1. Place the ignition switch in the ON position.
2. Close the door.
3. Open the window completely by operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.
5. Release the power window switch. Operate the window by the automatic function to
confirm the initialization is complete.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked by a
NISSAN dealer.
GUID-763E28EB-A953-4A35-A10F-6F137F82E26B
WARNING
. In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts
and child restraints.
. Do not allow anyone to stand up or
extend any portion of their body out
of the moonroof opening while the
vehicle is in motion or while the
moonroof is closing.
CAUTION
.Remove water drops, snow, ice or
sand from the moonroof before
opening.
. Do not place any heavy object on
the moonroof or surrounding area.
POWER MOONROOFGUID-60D1BFD6-832F-432D-8BEE-8F0AE9FFB2B4The moonroof only operates when the ignition
switch is in the ON position.
The moonroof is operational for about 45
seconds, even if the ignition switch is pushed
to the OFF position. If the driver's door or the
Instruments and controls2-51
MOONROOF (if so equipped)
& R Q G L W L R Q
Page 128 of 399
> ( G L W 0 R G H O ) ' @
2-52Instruments and controls
passenger's door is opened during this period of
about 45 seconds, power to the moonroof is
canceled.
SunshadeGUID-F2AE68AD-35BC-4AA8-83C0-4AA506392BF1The sunshade will open automatically when the
moonroof is opened. However, it must be closed
manually.
SIC4624
Sliding the moonroofGUID-F85D3D5F-862B-4CED-BA76-75CBE0FDAF74To fully open or close the moonroof, push the
switch toward
*1or*2and release
it; it need not be held. The roof will automatically
open or close all the way. To stop the roof, push
the switch in any direction while it is opening or
closing.
Tilting the moonroofGUID-5A375FB1-2459-4E69-B8C9-A8D87A6925A0To tilt up, first close the moonroof by pushing the
switch toward
*2. Push the switch toward
*2again and release it; it need not be
held. To tilt down the moonroof, push the switch
toward
*1.
Auto reverse functionGUID-05D9BD58-A278-4709-A03A-80DC088F07EC
WARNING
There are some small distances imme-
diately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., in-
side the vehicle before closing the
moonroof.
If the control unit detects something caught in
the moonroof when it is closing, the moonroof
will be immediately opened.
The auto reverse function can be activated when
the moonroof is closed by automatic operation
when the ignition switch is in the ON position or
for about 45 seconds after the ignition switch is
pushed to the OFF position.
If the moonroof cannot be closed automatically
when the auto reverse function activates due to
a malfunction, push and hold the switch toward
*2.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the moonroof
occurs.
& R Q G L W L R Q
Page 130 of 399
> ( G L W 0 R G H O ) ' @
2-54Instruments and controls
SIC4573
MAP LIGHT CONTROL SWITCH (if so
equipped)
GUID-D030AC73-6A5E-41D1-B4E5-4C8B6A705368The map lights control switch has three posi-
tions: ON
*1, OFF*2and center.
ON positionGUID-96EAA639-DA91-44C2-B280-951FC4FE7379When the switch is in the ON position*1, the
map lights will illuminate.
OFF positionGUID-315173DD-FC92-4382-95FF-5966BDBA76F5When the switch is in the OFF position*2, the
map lights will not illuminate, regardless of the
condition.
Center positionGUID-2C777A6B-3617-446F-8361-A456EE072540When the switch is in the center position, the
map lights will illuminate under the following
conditions:
. ignition switch is placed in the OFF position
Ð remain on for about 15 seconds.
. doors are unlocked by pushing the UN-
LOCK
button (on the Intelligent Key) or
the request switch with the ignition switch in
the LOCK position
Ð remain on for about 15 seconds.
. any door is opened and then closed with the
ignition switch in the LOCK position
Ð remain on for about 15 seconds.
. any door is opened with the ignition switch
in the ACC or ON position
Ð remain on while the door is opened.
When the door is closed, the lights go
off.
The lights will turn off after a period of
time when the lights remain illuminated to
prevent the battery from becoming dis-
charged.
CARGO LIGHTGUID-4E7D7193-19FC-43A7-8050-94552D64EF00The cargo room lights illuminate when the lift
gate is opened. When the lift gate is closed, the
lights will turn off.
& R Q G L W L R Q