brake NISSAN LEAF 2011 Manual PDF

.Do not place metalized film or any
metal parts (antenna, etc.) on the
windows. This may cause poor re-
ception of the signals from the tire
pressure sensors, and the TPMS will
not function properly.
Some devices and transmitters may temporarily
interfere with the operation of the TPMS and
cause the low tire pressure warning light to
illuminate. Some examples are:
. Facilities or electric devices using similar
radio frequencies that are near the vehicle.
. If a transmitter set to similar frequencies is
being used in or near the vehicle.
. If a computer (or similar equipment) or a DC/
AC converter is being used in or near the
vehicle.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation. NOTE:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.
For Canada:
This device complies with RSS-210 of
Industry Canada. Operation is subject to
the following two conditions: (1) this
device may not cause interference, and
(2) this device must accept any interfer-
ence, including interference that may
cause undesired operation of the device.
TPMS with Easy Fill Tire Alert
When tire pressure is low, the low tire pressure
warning light illuminates.
This vehicle provides visual and audible signals
to help you inflate the tires to the recommended
COLD tire pressure.
Vehicle set-up:
1. Park the vehicle in a safe and level place.
2. Apply the parking brake and push the P
position switch on the selector lever.
3. Place the power switch in the ON position. Do not place in the READY to drive mode. Operation:
1. Add air to the tire.
2. After a few seconds, the hazard indicators
will start flashing.
3. When the designated pressure is reached, the horn beeps once and the hazard
indicators stop flashing.
4. Perform the above steps for each tire.
. If the tire is over-inflated more than approxi-
mately 4 psi (30 kPa), the horn beeps and
the hazard indicators flash 3 times. To
correct the pressure, push the core of the
valve stem on the tire briefly to release
pressure. When the pressure reaches the
designated pressure, the horn beeps once.
. If the hazard indicator does not flash within
approximately 15 seconds after starting to
inflate the tire, it indicates that the Easy Fill
Tire Alert is not operating.
. The TPMS will not activate the Easy Fill Tire
Alert under the following conditions:
— If there is interference from an external
device or transmitter.
— The air pressure from the inflation device is not sufficient to inflate the tire such as
those using a power socket.

or ON position.
The power lock is designed so that the power
switch position cannot be switched to LOCK
until the vehicle is into the P (Park) position.
When the power switch cannot be switched to
the LOCK position, proceed as follows.
1. Push the P position switch on the selectorlever to place the vehicle in the P (Park)
position.
2. Push the power switch to the OFF position. The power switch position indicator
*Awill
not illuminate.
3. Open the door. The power switch will change to the LOCK position.
The vehicle can be moved from the P
(Park) position if the power switch is in
the ON position and the brake pedal is
depressed.
POWER SWITCH POSITIONS
LOCK (Normal parking position)
The power switch can only be locked in this
position.
The power switch will be unlocked when it is
pushed to the ACC position while the driver is
carrying the Intelligent Key.
ACC (Accessories)
This position activates electrical accessories,
such as the radio, when EV system is OFF.
ON
This position turns on the EV (Electric Vehicle)
system and electrical accessories.
READY (Normal operating position)
This position turns on the EV (Electric Vehicle)
system, electrical accessories and the vehicle
can be driven.
OFF
The EV (Electric Vehicle) system can be turned
off.
The power switch cannot be placed in the
LOCK position until the vehicle is in the P (Park)
position.

.Do not hang items on the selector
lever. This may cause an accident
due to a sudden start.
. Do not shift to the ECO position
abruptly on slippery roads. This may
cause a loss of control.
NOTE:
If the accelerator pedal is depressed when
the vehicle is in the D (Drive) or ECO
position and the driver’s seat belt is
securely fastened, the parking brake will
be released automatically. See “Electric
parking brake” later in this section.

NOTE:
.While the electric parking brake is
applied or released, an operating
sound is heard from the lower side of
the rear seat. However, this is not a
malfunction.
. When the electric parking brake is
frequently applied and released in a
short period of time, the electric park-
ing brake may not operate in order to
prevent the electric parking brake sys-
tem from overheating. If this occurs,
operate the electric parking brake
again after approximately 1 minute.
. The electric parking brake can be
released with the power switch in the
ON or READY to drive position.
. If the electric parking brake must be
applied while driving in an emergency,
pull up and hold the electric parking
brake switch. When you release the
parking brake switch, the parking
brake will be released.
. While pulling up on the electric parking
brake switch, the electric parking brake
is applied and a chime sounds. The
electric parking brake indicator light in
the meter and parking brake switch operation indicator illuminate. This
does not indicate a malfunction. The
electric parking brake indicator light
and parking switch operation indicator
turn off when the electric parking brake
switch is released.
. Pull up on the electric parking brake
switch twice so that the maximum
electric parking brake force can be
applied to the vehicle.
. When operating the electric parking
brake switch with the power switch in
the ON position, the electric parking
brake indicator light in the meter and
the electric parking brake switch op-
eration indicator turn on.
. Do not start driving while the parking
brake is applied. Doing so may cause
the parking brake to overheat or re-
duce its effectiveness, which could
result in an accident.
. When pulling the electric parking brake
switch with the power switch in the
OFF or ACC position, the electric park-
ing brake switch operation indicator
will continue to illuminate for a short
period of time.

speed driving you may feel that regenerative
brake provides less deceleration than the engine
braking in an ordinary vehicle. This is normal.
Less deceleration is provided by the regenera-
tive brake system when the Li-ion battery is fully
charged. Regenerative brake is automatically
reduced when the Li-ion battery is fully charged
to prevent the Li-ion battery from becoming
overcharged. Regenerative brake is also auto-
matically reduced when the battery temperature
is high/low (indicated by the red/blue zones on
the battery temperature gauge) to prevent Li-ion
battery damage.
The brake pedal should be used to slow or stop
the vehicle depending on traffic or road condi-
tions. The vehicle brakes are not affected by
regenerative brake system operation.
NOTE:
.When applying the regenerative
brakes, you may hear a sound coming
from the regenerative brake system.
This is a normal operating character-
istic of an EV (Electric vehicle) .
. If the power switch position is in a
position other than ON or READY to
drive, you can stop the vehicle by
depressing the brake pedal. However,
greater foot pressure on the brake pedal will be required to stop the
vehicle, and the stopping distance will
be longer.
. When depressing the brake pedal, the
braking pedal feel will not be smooth
or may change when the cooperative
regenerative brake system activates.
However, the electronically controlled
brake system is operating normally and
this does not indicate a malfunction.
Using brakes
Avoid resting your foot on the brake pedal while
driving. This will cause overheating of the
brakes, wearing out the brake pads and shoes
faster and will reduce driving range.
To help reduce brake wear and to prevent the
brakes from overheating, reduce speed and
select ECO position before going down a slope
or long grade. Overheated brakes may reduce
braking performance and could result in loss of
vehicle control.

ELECTRIC PARKING BRAKE
BREAK-IN
Break in the parking brake shoes whenever the
holding effect of the parking brake is weakened
or whenever the parking brake shoes and/or
drums are replaced, in order to maintain
optimum braking performance.
This procedure is described in the vehicle
Service Manual, and it can be performed by a
NISSAN certified LEAF dealer.
ANTI-LOCK BRAKING SYSTEM
(ABS)

the power switch is placed in the OFF position
then back to the ON position.
The computer has a built-in diagnostic feature
that tests the system each time you start the EV
(Electric Vehicle) and move the vehicle forward
or in reverse at a slow speed. When the self-test
occurs, you may hear a “clunk” noise and/or feel
a pulsation in the brake pedal. This is normal and
is not an indication of a malfunction.

6 In case of emergency
Roadside assistance program .............................................. 6-2
Emergency EV (Electric Vehicle) shut off .......................... 6-2 Flat tire ........................................................................................ 6-2
Tire Pressure Monitoring System (TPMS) ................... 6-2
Repairing flat tire ................................................................ 6-3
Jump starting ............................................................................. 6-9
If the Li-ion battery becomes completely discharged ... 6-11 Push starting .......................................................................... 6-12
Tools ........................................................................................ 6-12
Towing your vehicle ............................................................. 6-13
Towing recommended by NISSAN .......................... 6-14
Vehicle recovery (freeing stuck vehicle) ................. 6-15
Parking brake mechanical release ................................... 6-16

in the P (Park) position, and the electric
parking brake cannot be applied. If this
occurs, place suitable blocks at both
the front and back of a wheel to prevent
the vehicle from moving. Failure to
block a wheel may allow the vehicle to
move unexpectedly which may result in
serious personal injury or death.
To place the vehicle in the READY position so
the vehicle can be driven, charge the Li-ion
battery until the driving range on the instrument
panel changes from “---” to a numeric distance.

.Never tow a vehicle using the vehi-
cle tie down hook or recovery hook.
. Always pull the cable straight out
from the front of the vehicle. Never
pull on the vehicle at an angle.
. Pulling devices should be routed so
they do not touch any part of the
suspension, steering, brake or cool-
ing systems.
. Pulling devices such as ropes or
canvas straps are not recommended
for use in vehicle towing or recov-
ery.
Rocking a stuck vehicle
If the vehicle is stuck in sand, snow, mud, etc.,
try to free it by following the procedure below.
1. Turn off the Vehicle Dynamic Control (VDC)
system.
2. Make sure the area in front and behind the vehicle is clear of obstructions.
3. Turn the steering wheel left and right to clear an area around the front tires.
4. Slowly rock the vehicle forward and back- ward.
.Shift back and forth between the R
(Reverse) and D (Drive) positions.
.Apply the accelerator as little as possible
to maintain the rocking motion.
.Release the accelerator pedal before
shifting between R and D.
.Do not spin the tires above 35 MPH (55
km/h).
5. If the vehicle cannot be freed after a few tries, contact a professional towing service
to remove the vehicle.