light NISSAN MAXIMA 2012 A35 / 7.G 08IT Navigation Manual

Black plate (78,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-16
Setting destination
1. Push .
2. Highlight [Next Page] and push .3. Highlight [Freeway Entrance/Exit] and push
. A character input screen is
displayed.
4. Enter the name of the freeway.
5. After finishing the entry, highlight [List] and
push .6. Highlight the freeway of the destination from
the list, and push .
7. Highlight [Entrance] or [Exit] and push
. A list screen is displayed.8. Select the preferred destination from the list.
The position of the selected location is
displayed in the preview on the right side
of the screen. Then, push .

Black plate (79,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
INFO:
By selecting [By Distance], the list can be
sorted by the nearest distance.
9. The entire route is shown on the map. Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)
SETTING INTERSECTIONAn intersection of any two streets can be set as
the destination to which the system calculates a
route.1. Push .
2. Highlight [Next Page] and push .
3. Highlight [Intersection] and push
. A character input screen is
displayed.4. Enter the name of the 1st street.
After finishing the entry, highlight [List] and
push . A list screen is displayed.
Setting destination
4-17

Black plate (80,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-18
Setting destination
5. Highlight a street as the 1st street from the list and push . A character input
screen is displayed.6. Enter the name of the 2nd street.
After finishing the entry, highlight [List] and
push . A list screen is displayed.
7. Highlight a street as the 2nd street from the
list and push .8. The entire route is shown on the map.
Highlight [Start] after confirming the location
of the displayed dest ination, and push
. The system sets the destination
to the selected location and starts calculat-
ing a route.
INFO:
Even after setting a destination, the location of
the destination can be adjusted, the route can
be stored, etc.“Procedures after setting destination”
(page 5-2)
SETTING CITY CENTERThe system can calculate a route to the center of
a city, without setting a specific location.1. Push .
2. Highlight [Next Page] and push .

Black plate (81,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
3. Highlight [City Center] and push . A character input screen is
displayed.4. Enter the name of the city, highlight [List]and push . A list screen is
displayed.
INFO:
Highlight [Last 5 Cities] and push
to display 5 cities recently set
as destinations.
5. Highlight the preferred destination from the list and push . The position of the
selected location is displayed in the preview
on the right side of the screen.
INFO:
By selecting [By Distance], the list can be
sorted by the nearest distance.
6. The selected destination is displayed at the center of the map. Highlight [Start] after
confirming the location of the displayed
destination, and push . The system sets the destination to the
selected location and starts calculating a
route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING POINT ON MAPA location scrolled to on the map can be set as
the destination to which the system calculates a
route.1. Scroll the map, place the cross pointer over the preferred location, and push .
Setting destination
4-19

Black plate (82,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
4-20
Setting destinationINFO:.
Adjust the map scale to search for a location more effectively.
.
The point on the blinking road where thecenter of the cross pointer is located can
be set as a destination.
2. Highlight [New Dest.] and push .
INFO:
For the items except for [New Dest.], refer to
“Map menu screen”.
“Scrolled location map screen”
(page 2-17)
3. The system sets the destination to the selected location and starts calculating a
route.
INFO:
If a point on a freeway is set as the destination, a
confirmation message is displayed. It is possible to delete a destination and all
waypoints that have already been set.
1. Press
.
2. Select [Delete Destination] and press .3. A confirmation message is displayed. Select
[Yes] and press .
The destination and the waypoints are
deleted.DELETE DESTINATION

Black plate (86,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-2
Route guidance
After performing a route search, the route
guidance can be started immediately. Also, it is
possible to confirm or change a route.AVAILABLE ITEMS AFTER SETTING
DESTINATION. [Start]:
Starts route guidance to the selected
destination.
“Starting route guidance” (page 5-2)
. [More Routes]:
Displays 3 alternative routes.“Selecting route” (page 5-3)
. [Add/Route Info]:
Displays the route information or add a
destination or a waypoint.“Confirming route” (page 5-3)
. [Move Location]:
Displays a map screen and allows the
location of the destination to be adjusted.
“Moving location of destination”
(page 5-4)
. [Store Location]:
Stores the location in the Address Book.“Storing location” (page 5-5)
. [Place Info]:
Displays information about the facility that is
set as the destination if it is included in the
map data.“Viewing information about searched
location” (page 5-5)
INFO:
. If no operations are performed on the
system for several seconds, [Start] is auto-
matically selected, and the system starts
route guidance.
. When using waypoints, [More Routes] is
disabled. After the route is started, push
then select [Edit/Add to Route]
to change the route between each waypoint.
“Editing route” (page 5-14)
. The same screen as when [Move Location]
is selected can be displayed with the
following operations:
— Touching the map screen — Pushing the directional buttons except
for the up/down button (multi-function
controller with directional buttons)
— Pushing the slide switch except in the upward/downward direction (multi-func-
tion controller without directional but-
tons)
STARTING ROUTE GUIDANCE1. Highlight [Start] and push .
Route guidance starts.
PROCEDURES AFTER SETTING
DESTINATION

Black plate (87,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
SELECTING ROUTE1. Highlight [More Routes] and push .2. Highlight the preferred route condition and
push .
3. The display automatically returns to the previous screen.Available route conditions.[Short. Time] (purple):
Prioritizes by the shortest time. .
[Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
. When a route condition is selected, a
preview is displayed on the right side of
the screen.
. The 3 routes may not always be different.
CONFIRMING ROUTE1. Highlight [Add/Route Info] and push
.
2. Highlight the preferred information item and push .
3. Push to return to the previous
screen.
Available information. [Turn List]:
Displays the details of the suggested route.
“Using turn list” (page 5-19)
. [Preview]:
The system will trace the planned route
going forward or in reverse.“Using route preview” (page 5-19)
. [Add Way Pt.]:
Add a waypoint or a destination.“Adding destination or waypoint”
(page 5-4)
. [Store Route]:
A calculated route can be stored. A max-
imum of 5 routes can be stored. Stored
routes can be easily retrieved and set as the
suggested route.“Storing route” (page 6-5)
Route guidance
5-3

Black plate (88,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
5-4
Route guidance
. [Map Scroll]:
Displays a map screen where the location of
the destination can be confirmed.
The same screen as when [Map Scroll] is
touched can be displayed with the following
operations:
— Touching the map screen.
— Pushing the directional buttons except for the up/down button (multi-function
controller with directional buttons) .
— Pushing the slide switch except in the upward/downward direction (multi-func-
tion controller without directional but-
tons) .Adding destination or waypointBefore starting route guidance, destinations
and/or waypoints can be added. A total of 6
destinations or waypoints can be set.
1. Highlight [Add Way Pt.] and push .2. Set additional destinations or waypoints and
push .
The method of searching for a location is the
same as the one for a destination.
“4. Setting destination”
3. Highlight [Add Destination] or [Add Way- point] and push .
4. The system starts calculating a route that
includes the added destination or waypoint.
When the calculation is finished, the route is
displayed.
INFO:.
If a waypoint was added, [More Routes]
cannot be selected.
.
If a destination was added, the priordestination becomes a waypoint.
MOVING LOCATION OF DESTINATIONThe location of the destination can be adjusted
by moving the cross pointer across the map.

Black plate (89,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
1. Highlight [Move Location] and push .
INFO:
The screen for adjusting the location also
changes by touching the map screen dis-
played on the right side of the screen.
2. Adjust the location by moving the cross pointer across the map and push
. The location of the destination
is modified.
INFO:
. The map scale can be changed by pressing
or (if so
equipped) . The map scale can also be
changed by touching the scale icon.
. The same screen as when [Move Location]
is touched can be displayed with the
following operations:
— Touching the map screen.
— Pushing the directional buttons except up/down buttons (multi-function control-
ler with directional buttons) .
— Pushing the slide switch except upward/ downward (multi-function controller with-
out directional buttons) .
STORING LOCATIONA searched location can be stored in the
Address Book. Then it can be easily retrieved
and set as a destination (or waypoint) .
1. Highlight [Store Location] and push .2. The location is stored in the Address Book.
The corresponding icon is displayed at the
set location on the map.VIEWING INFORMATION ABOUT
SEARCHED LOCATIONInformation (street address and phone number)
about places stored in the map data can be
displayed.
Route guidance
5-5

Black plate (93,1)
[ Edit: 2011/ 6/ 13 Model: 08NJ-N ]
GUIDANCE SCREEN SETTINGSThe guidance screen can be displayed at all
times even when the vehicle is located away
from the guide point. The screen to be displayed
can be set.Split screen settingsThe display setting on the left-hand side screen
shown during route guidance can be changed.1. Push while the current location
map screen is displayed.
2. Highlight [Map View ] and push .
3. Highlight [View Settings] and push
.
4. Highlight the preferred screen and push . The indicator of the selected
screen illuminates.
Intersection:The map screen and the enlarged intersection
view can be displayed at the same time.
Push