key NISSAN MURANO 2003 1.G Owner's Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: MURANO, Model: NISSAN MURANO 2003 1.GPages: 265, PDF Size: 2.03 MB
Page 100 of 265
LOCKING WITH KEY
PowerThe power door lock system allows you to lock
or unlock all doors simultaneously.
Turning the driver’s door key to the front of
the vehicle will lock all doors (including the
back door) and fuel filler lid.
Turning the driver’s door key one time to the
rear of the vehicle will unlock the driver’s
door. From that position, returning the key to
neutral (where the key can only be removed
and inserted) and turning it to the rear againwithin 5 seconds will unlock all doors and fuel
filler lid.
Opening and closing front windowsTurn the driver’s door key to the unlock position
and hold for about 1 second, the front windows
will begin to lower.
To stop opening, turn the key to the neutral
position.
To close the front windows with the door key
cylinder, turn the key to the lock position and
hold for about 1 second.
To stop closing, turn the key to the neutral
position.
In the event of a hand in the way, or other
obstruction, the auto reverse function will acti-
vate.
LOCKING WITH INSIDE LOCK
KNOBTo individually lock the doors, move the inside
lock knobto the LOCK position, then close the
door. To unlock, pull up the inside lock knobto
the UNLOCK position.
The front doors will automatically be unlocked
and you can open the door by pulling the inside
door handle.
When locking the door without a key, be
sure not to leave the key inside the vehicle.
SPA1575
SPA1422
Pre-driving checks and adjustments
3-3
03.1.28/Z50-D/V5.0
Page 101 of 265
LOCKING WITH POWER DOOR
LOCK SWITCHAll door and fuel filler lid locks will be engaged
when the power door lock switch is moved to the
LOCK position with the driver’s or front passen-
ger’s door open. Then close the door and all
doors will be locked.
When the power door lock switch is moved to
the LOCK position with front doors open while a
key is in the ignition switch, all doors will lock
once and then unlock automatically.
CHILD SAFETY REAR DOOR LOCKChild safety locking helps prevent doors from
being opened accidentally, especially when
small children are in the vehicle.
When the lever is in the lock position, the
rear door can be opened only from the
outside.It is possible to lock/unlock all doors (including
the back door) and fuel filler lid and activate the
panic alarm by using the keyfob from outside the
vehicle.
Before locking the doors, make sure the
key is not left in the vehicle.
The keyfobcan operate at a distance of approxi-
mately 33 ft (10 m) from the vehicle. (The
effective distance depends upon the conditions
around the vehicle.)
As many as five keyfobs can be used with one
vehicle. For information concerning the purchase
and use of additional keyfobs, contact your
NISSAN dealer.
The keyfobwill not function when:
the battery is dead,
the distance between the vehicle and the
keyfobis over 33 ft (10 m).
The panic alarm will not activate when the
key is in the ignition switch.
CAUTION
The following conditions or occurrences
will damage the keyfob.
SPA1576
SPA1577
REMOTE KEYLESS ENTRY
SYSTEM
3-4
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 102 of 265
Do not allow the keyfob to become
wet.
Do not drop the keyfob.
Do not strike the keyfob sharply
against another object.
Do not place the keyfob for an ex-
tended period in an area where tem-
peratures exceed 140°F (60°C).
If a keyfob is lost or stolen, NISSAN
recommends erasing the ID code of that
keyfob. This will prevent the keyfob
from unauthorized use to unlock the
vehicle. For information regarding the
erasing procedure, please contact a
NISSAN dealer.HOW TO USE REMOTE KEYLESS
ENTRY SYSTEM
Setting hazard indicator and horn
modeThis vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
In hazard indicator and horn mode, when theLOCK button is pushed, the hazard indicator
flashes twice and the horn chirps once. When
the UNLOCK button is pushed, the hazard indi-
cator flashes once.
If hazard indicator and horn mode is not neces-
sary, you can switch to hazard indicator only
mode by following the switching procedure.
In hazard indicator only mode, when the LOCK
button is pushed, the hazard indicator flashes
twice. When the UNLOCK button is pushed,
neither the hazard indicator nor the horn oper-
ates.
(Switching procedure)
Push the LOCK and UNLOCK buttons on the
keyfobsimultaneously for more than 2 seconds
to switch from one mode to the other.
When pushing the buttons to set hazard indica-
tor only mode, the hazard indicator flashes 3
times.
When pushing the buttons to set hazard indica-
tor and horn mode, the hazard indicator flashes
once and the horn chirps once.
Pre-driving checks and adjustments
3-5
03.1.28/Z50-D/V5.0
Page 103 of 265
Locking doors and fuel filler lid1. Remove the ignition key.*1
2. Close all the doors and fuel filler lid.*2
3. Push the LOCK button on the keyfob.
4. All the doors and fuel filler lid will lock.
All of the doors will lock when the LOCK
button on the keyfob is pushed even
though a door remains open and/or the
ignition key is in the ONposition.
5. The hazard indicator flashes twice and the
horn chirps once.When the LOCK button is pushed with all
doors and fuel filler lid locked, the hazard
indicator flashes twice and the horn chirps
once as a reminder that the doors and fuel
filler lid are already locked.
*1: Doors and fuel filler lid lock with the keyfob
while a key is in the ignition switch. How-
ever, the panic alarm will not activate when
the key is in the ignition switch.
*2: Doors and fuel filler lid lock with the keyfob
while any door is open. However, hazard
indicator and horn mode will not function.
Unlocking doors1. Push the UNLOCK button on the keyfob
once.
The driver’s door and fuel filler lid unlocks
The hazard indicator flashes once if all doors
and fuel filler lid are completely closed with
the ignition key in any position except the ON
position.
The interior light turns on and the light timer
activates for 30 seconds when the switch is
in the DOOR position with the ignition key in
any position except the ON position.
SPA1260
SPA1397
3-6
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 104 of 265
2. Push the UNLOCK button on the keyfob
again within 5 seconds.
All doors unlock
The hazard indicator flashes once if all doors
are completely closed.
If the following operation is not carried out
within 1 minute after pressing the
UNLOCK button, all doors will be locked
automatically.
any door is opened.
the ignition key is turned to the ON
position
The interior light can be turned off without
waiting for 30 seconds by turning the ignition
switch to the ON position or by locking the
doors with the keyfob.Opening the front windowPush the UNLOCK button on the keyfob.
The driver’s door will unlock.
Continue to press the UNLOCK button for 3
seconds. The driver’s and front passenger’s
windows will be lowered.
Continue to press the UNLOCK button until
windows are fully open.To stop lowering the windows, release the UN-
LOCK button.
To start lowering the windows, press the UN-
LOCK button again for 3 more seconds.
This function will operate after the ignition switch
is off and 45 seconds passed or either the front
door is opened.
Using the panic alarmIf you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
1. Push the PANIC button on the keyfob for
longer than 0.5 seconds.
2. The theft warning alarm and headlights will
stay on for 30 seconds.
3. The panic alarm stops when:
It has run for 30 seconds, or
The LOCK or the UNLOCK button is
pressed, or
The panic button is pushed on the keyfob for
more than 0.5 seconds.
BATTERY REPLACEMENTReplace the battery as follows:
1. Open the lid using a suitable tool.
2. Replace the battery with a new one.
SPA1374
Pre-driving checks and adjustments
3-7
03.1.28/Z50-D/V5.0
Page 105 of 265
Recommended battery: Sanyo CR2025 or
equivalent
Make sure that the⊕side faces the
bottom case.
3. Close the lid securely.
4. Push the keyfobbutton two or three times to
check its operation.
See your NISSAN dealer if you need any assis-
tance for replacement.
If the battery is removed for any reason
other than replacement, perform the step 4
above.
Be careful not to touch a circuit board
and a battery terminal.
An improperly disposed battery can
harm the environment. Always confirm
local regulations for battery disposal.
The keyfob is water-resistant; however,
if it does get wet, immediately wipe
completely dry.
When changing batteries, do not let
dust or oil get on the keyfob.
FCC Notice:
Changes or modifications not expressly
approved by the manufacturer compliancecould void the user’s authority to operate
the equipment. This device complies with
Part 15 of the FCC Rules and RSS-210 of
Industry Canada. Operation is subject to
the following two conditions: (1) This de-
vice may not cause harmful interference,
and (2) this device must accept any inter-
ference received, including interference
that may cause undesired operation of the
device.
3-8
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 108 of 265
OPEN THE FILLER LIDTo open the fuel filler lid, unlock it using one of
the following operations, then push the right-
hand side of the lid
A.
Press the unlock button on the keyfob once.
Insert the key into the door lock cylinder and
turn the door key clockwise twice.
Press the power door lock switch to the
unlock side.
To lock, close the fuel filler lid and lock the doors.
FUEL FILLER CAPThe fuel filler cap is a ratcheting type. Tighten the
cap clockwise until ratcheting clicks are heard.
Put the fuel filler cap on the cap holder while
refueling.
WARNING
Gasoline is extremely flammable and
highly explosive under certain condi-
tions. You could be burned or seri-ously injured if it is misused or mis-
handled. Always stop the engine and
do not smoke or allow open flames
or sparks near the vehicle when refu-
eling.
Fuel may be under pressure. Turn the
cap a quarter turn, and wait for any
hissing sound to stop to prevent fuel
from spraying out and possible per-
sonal injury. Then remove the cap.
Do not attempt to top off the fuel
SPA1580
SPA1581
FUEL FILLER LID
Pre-driving checks and adjustments
3-11
03.1.28/Z50-D/V5.0
Page 113 of 265
ignition switch is in the ACC or ON position.
Move the switch to right
A
or left
B
to select
the right or left outside mirror, then adjust the
mirror to the desired position by pushing the
button
C.
Foldable outside mirrorsPush the outside mirror backward to fold it.
AUTOMATIC DRIVE POSITIONER
OPERATIONThis system is designed so that the driver’s seat,
outside mirror and pedals (Brake, Accelerator)
will automatically move when the selector lever is
in the P (Park) position. This allows the driver to
get in and out of the driver’s seat more easily.
When one of the following conditions is met, the
driver’s seat will slide backward while the selec-
tor lever is in the P (Park) position:
When the key is removed from the ignition
switch.
When the driver’s door is opened with the
key turned to LOCK.
When the key is turned from ACC to LOCK
with the driver’s door open.
When one of the following conditions is met
while the selector lever is in the P (Park) position,
the driver’s seat will return to the positions
before being set.
When the key is inserted into the ignition
switch.
When the driver’s door is closed with the key
turned to LOCK.
When the key is turned from ACC to ON.
MPA0008
AUTOMATIC DRIVE POSITIONER
(if so equipped)
3-16
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0
Page 114 of 265
PROCEDURE FOR STORING
MEMORYTwo positions can be stored in the automatic
drive positioner memory.Follow these proce-
dures to use the memory system.
1. Set the selector lever to the P (Park)
position.
2. Turn the ignition ON.
3. Adjust the driver’s seat, outside mirrors and
pedals to the desired positions by manually
operating each adjusting switch. For addi-
tional information, see “Seats” in the “1.
Seats, restraints and supplemental air bag
systems” section and “Pedal position adjust-
ment” earlier in this section.
During this step, do not turn the ignition to
any positions other than ON.
4. Push the SET switch and, within 5 seconds,push the memory switch 1 or 2 fully for at
least 1 second.
The indicator light for the pushed memory
switch will come on and stay on for approxi-
mately 5 seconds after pushing the switch.
After the indicator light goes off, the selected
positions are stored in the selected memory
(1 or 2). Pushing the unlock button on the
keyfobwithin this 5 seconds, will link the
selected memory to the keyfob.
When the link is completed, the indicator light
of the selected memory switch will blink for
approximately 5 seconds.
When you unlock the door with the link
completed keyfob, the driver’s seat will move
back and move to the memorized position.
If memory is stored in the same memory
switch, the previous memory and the memory
which is linked to the keyfob, will be deleted.
Confirming memory storageTurn the ignition ON and push the SET
switch. If the main memory has not been
stored, the indicator light will come on for
approximately 0.5 seconds. When the
memory has stored the position, the indicator
light will stay on for approximately 5 seconds.
If the battery cable is disconnected, or if the
SPA1584
Pre-driving checks and adjustments
3-17
03.1.28/Z50-D/V5.0
Page 115 of 265
fuse blows, the memory will be canceled. In
such a case, reset the desired positions
using the following procedures.
1. Open and close the driver’s door more than
two times with the ignition key in the LOCK
position.
2. Reset the desired position using the previous
procedure.
Selecting the memorized position1. Set the selector lever to the P (Park) position.
2. Turn the ignition ON.
3. Push the memory switch 1 or 2 fully for at
least 1 second.
The driver’s seat, pedals and outside mirror
will move to the memorized position with the
indicator light flashing. Then the light will stay
on for approximately 5 seconds.Cancellation of the systemThe automatic drive positioner system can be
canceled.
See “4. Display screen, heater, air conditioner
and audio systems” section.System operationThe automatic drive positioner system will notwork or will stop operating under the following
conditions:
when the vehicle speed is above 4 MPH (7
km/h).
when either of the memory switches is
pressed while the automatic drive positioner
is operating.
when the adjusting switch for the driver’s
seat, pedal or outside mirror is turned on
while the automatic drive positioner is oper-
ating.
when the memory switch 1 or 2 is not pushed
for at least 1 second.
when the seat, pedal and outside mirror has
already been moved to the memorized posi-
tion.
when no seat position is stored in the
memory switch.3-18
Pre-driving checks and adjustments
03.1.28/Z50-D/V5.0