transmission NISSAN MURANO 2012 2.G Warranty Booklet

LIMITATION OF WARRANTIES AND OTHER
WARRANTY TERMS AND STATE LAW
RIGHTS
EXTRA EXPENSES - LIMITATIONS OF DAMAGES
This warranty does not cover incidental or
consequential damages such as loss of the
use of the vehicle, inconvenience or commer-
cial loss.
ANY IMPLIED WARRANTY OF MERCHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PUR-
POSE SHALL BE LIMITED TO THE DURATION
OF THIS WRITTEN WARRANTY.
Some states do not allow the exclusion or limitation
of incidental or consequential damages or limita-
tions on how long an implied warranty lasts, so the
above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights,
and you may also have other rights which vary from
state to state.
Nissan does not authorize any person to create for
it any other warranty, obligation or liability in con-
nection with this vehicle.
THE WARRANTY BEGINS
The warranty period begins on the date the vehicle is
delivered to the first retail buyer or put into use, which-
ever is earlier.
FOR HOW LONG AND WHAT IS
COVERED
BASIC COVERAGEThe basic coverage period is 36 months or
36,000 miles, whichever comes first.
This warranty covers any repairs needed to cor-
rect defects in materials or workmanship of all
parts and components of each new Nissan ve-
hicle supplied by Nissan subject to the exclusions
listed under the heading “WHAT IS NOT COV-
ERED” or, if the part is covered by one of the
separate coverages described in the following
sections of this warranty, that specific coverage
applies instead of the basic coverage.
Bedliners will be repaired to commercially ac-
ceptable standards subject to the conditions and
limitations listed in WHAT IS NOT COVERED.
POWERTRAIN COVERAGEThe Powertrain coverage period is 60 months or
60,000 miles, whichever comes first.
This warranty covers any repairs needed to cor-
rect defects in materials or workmanship.
Powertrain coverage applies to components
listed below under the headings, Engine, Trans-
mission and Transaxle, Drivetrain, and Restraint
System, supplied by Nissan subject to the exclu-
sions listed under the heading “WHAT IS NOT
COVERED”. ENGINE
Cylinder heads and block and all internal parts,
rocker covers and oil pan, valve train and front
cover, timing chain and tensioner, oil pump, water
pump and fuel pump, fuel injectors, intake and
exhaust manifolds and supercharger, flywheel,
seals, and gaskets.
TRANSMISSION AND TRANSAXLE
Case and all internal parts, torque converter and
converter housing, automatic transmission control
module, transfer case and all internal parts, seals
and gaskets, clutch cover and housing A/T cooler,
and electronic transmission controls.
DRIVETRAIN
Drive shafts, final drive housing, and all internal
parts, propeller shafts, universal joints, bearings,
seals and gaskets.
RESTRAINT SYSTEM
Air bags and related electronic control systems.
CORROSION COVERAGE (PERFORATION
FROM CORROSION)
Any body sheet metal panel supplied by Nissan
found to have developed perforation (rust-
through) due to corrosion in normal use is covered
for 60 months, regardless of mileage, subject to
the exclusions listed under the heading “WHAT IS
NOT COVERED”. No additional rust proofing ap-
plications are required. Perforation is a condition
in which any body sheet metal panel has corroded
from one surface through to another.
(Continued on next page)
6 2012 NEW VEHICLE LIMITED WARRANTY

LONG-TERM EMISSION SYSTEM
DEFECTS WARRANTY PARTS LIST
EGI Wiring
Harness
Throttle Body
Intake Manifold
Engine Control
Module
o
Fuel Tank
Exhaust Manifold
w/Catalytic Converter
o
Front Exhaust Tube
w/Catalytic Converter
RHoFront Exhaust Tube
w/Catalytic Converter
o
Flywheel
Torque Converter
Drive Plate
Transmission
Control Module
Air Fuel Ratio
Sensor, Front (LH)
Air Fuel Ratio
Sensor, Front
Front Exhaust Tube
Muffler Assy
w/Catalytic Converter
o
Three-Way
Catalyst
o
Intake Manifold
Collector
Exhaust
Manifold, RH
Exhaust Manifold
Knock Sensor
Mass Air Flow
Sensor
Turbocharger
JukeXXXXXX X X X XX
Versa1.6L XXXXX XX
Versa1.8L XXXXX X
cube XXXXXX X X
Sentra2.0L XXXXXX XXX X
Rogue XXXXXX X X X
Altima 2.5L X XX X X XXX X
Altima SULEV
2.5L
ooXX XXX X X XX
Sentra2.5L XXXXXX XXX X
Frontier2.5L XXXXXX XX X
Murano X XX X XX X XX X X X
Murano Convert-
ible XX XX
X XX X XXXX
Quest X XX X XX X X X X XX
Altima 3.5L X XX X X X X X XX
M axim a XXXX XXX XXXX
370Z Coupe X XXXX XXXX X XXX
370Z Roadster X XXXX XXXX X XXX
(Continued on next page)
14CALIFORNIA VEHICLE EMISSION CONTROL WARRANTIES1, 2

EGI Wiring
Harness
Throttle Body
Intake Manifold
Engine Control
Module
o
Fuel Tank
Exhaust Manifold
w/Catalytic Converter
o
Front Exhaust Tube
w/Catalytic Converter
RHoFront Exhaust Tube
w/Catalytic Converter
o
Flywheel
Torque Converter
Drive Plate
Transmission
Control Module
Air Fuel Ratio
Sensor, Front (LH)
Air Fuel Ratio
Sensor, Front
Front Exhaust Tube
Muffler Assy
w/Catalytic Converter
o
Three-Way
Catalyst
o
Intake Manifold
Collector
Exhaust
Manifold, RH
Exhaust Manifold
Knock Sensor
Mass Air Flow
Sensor
Turbocharger
Frontier 4.0LXX X XX X XXX X
X te rra XXX X XX XXXX
Pathfinder 4.0L XX X XX X XX X X
Pathfinder 5.6L X X X X X X
Armada XX X X X
Titan XX X X X
(Continued on next page)
o = Long Term Federal Emission Parts covered for 96 months or 80,000 miles.
oo = Altima SULEV ONLY: All Long Term Emission Parts covered for 96 months or 100,000 miles. Please refer to underhood Vehicle Emission Information label to determine emission
certification level.
CALIFORNIA VEHICLE EMISSION CONTROL WARRANTIES1, 215

WHEEL ALIGNMENT AND BALANCING
Wheel alignment and balancing are important for safety
and maximum mileage from your tires. Check how your
tires are wearing at least once a month. If your tires are
wearing unevenly, such as the inside shoulder of the tire
wearing faster than the rest of the tread, or if you detect
excessive vibration, your vehicle may be out of align-
ment or balance. These conditions not only shorten the
life of your tires, but adversely affect the handling char-
acteristics of your vehicle which could be dangerous. If
you detect irregular wear or vibration, have your align-
ment and balance checked immediately. Tires which
have been run underinflated will show more wear on the
shoulders than in the center of the tread.
HARD BRAKING
You must inspect your tires after any hard braking cir-
cumstances or after tires have slid on the pavement.
This can cause a flat spot in a section of the tire tread.
TIRE SPINNING
Never spin your tires above a speedometer reading of
35 mph (55 km/h) if your vehicle becomes stuck. The
centrifugal force generated by the free spinning
tire/wheel assembly may cause a sudden tire explosion,
resulting in vehicle damage and/or serious personal
injury or death. Never allow anyone to stand near or
behind a tire spinning at high speed while attempting to
push a vehicle that is stuck. When in mud, sand, snow,
ice or other slippery conditions, do not indulge in exces-
sive wheel spin. In such conditions, with automatic
transmission vehicles, by accelerating the engine ex-
cessively, it is possible to spin one of the drive tiresbeyond its speed capability. This is also true when
balancing a drive tire/wheel assembly using the engine
of the vehicle to spin the wheel.
TIRE TREAD
Tires must be replaced when the depth of the tread
reaches 2/32 inch (1.6 mm) . Tires are manufactured
with tread wear indicators molded into the tire grooves
which indicate tread wearout. As tires approximate 2/32
inch (1.6 mm) wearout, the tread gauge becomes thin-
ner and more vulnerable to the effects of road hazards.
Also, worn tires are more subject to hydroplaning, which
can cause loss of control. Therefore, visual tire inspec-
tion becomes more crucial as the tires wear out.
WORN TIRES
Never drive on worn tires. Tires should be replaced by
trained personnel when 2/32nds of an inch tread depth
remains, as indicated by the tread wear indicators
molded into the tread grooves. In most states, it is illegal
to drive with less than 2/32nds of an inch of tread
remaining.
TIRE MIXING
For best performance select tires similar in size and load
rating to the original equipment tires. It is recommended
that the same size and type of tire be used on all four
wheel positions. In certain tires, casing ply material and
ply construction may vary as indicated on the sidewall of
the tire. When changing or replacing tires, it is preferred
that all four tires are the same construction type (i.e.,
High Performance, All Season, Mud & Snow) and con-
struction (Radial or Bias Ply) . Before mixing tires ofdifferent types on a vehicle in any configuration, be sure
to check the vehicle OWNER’S MANUAL for its recom-
mendations.
Tires which meet the Rubber Manufacturer’s Associa-
tion (RMA) definition of mud and snow tires are marked
M/S, M+S, M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are
not recommended for mud and/or snow driving.
If snow tires are needed, it is necessary to select tires
equivalent in size and load rating to the original equip-
ment tires. Always fit performance snow tires in sets of
four (4) for optimum mud & snow traction and mainte-
nance of vehicle handling characteristics. If you do not,
it may adversely affect the safety and handling of your
vehicle. It is also important to check the vehicle OWN-
ER’S MANUAL before mixing or matching tires on
4-wheel drive vehicles as this may require special pre-
cautions.
Please refer to your OWNER’S MANUAL for more
information on tire replacement precautions.
TIRE ROTATION
Tires on your Nissan vehicle should be rotated every
7,500 miles or as irregular wear develops. If irregular
wear becomes apparent or if the wear rate on the tires is
perceptibly uneven, the tires should be rotated in such a
way to alleviate the problem. Check your vehicle for any
mechanical problems and correct if necessary. Any
rotation pattern or procedure may be followed including
those indicated in the OWNER’S MANUAL. Some tires
have arrows on the sidewall showing the direction in
(Continued on next page)1 Provided by and published at the request of the tire manufacturers/warrantors.
44
IMPORTANT TIRE SAFETY INFORMATION1