warning NISSAN MURANO 2013 2.G Owners Manual

Black plate (168,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-16Pre-driving checks and adjustments
GUID-2CA37571-0169-4EEF-8C1B-5C2849855720
WARNING
The Intelligent Key transmits radio
waves when the buttons are pushed.
The FAA advises that radio waves may
affect aircraft navigation and commu-
nication systems. Do not operate the
Intelligent Key while on an airplane.
Make sure the buttons are not operated
unintentionally when the unit is stored
for a flight.
It is possible to lock/unlock all doors and the lift
gate/trunk lid, activate the panic alarm and open
the windows and lift gate/trunk lid (if so
equipped) by pushing the buttons on the
Intelligent Key from outside the vehicle.
Before locking the doors, make sure the
Intelligent Key is not left in the vehicle.
The LOCK/UNLOCK button on the Intelligent
Key can operate at a distance of approximately
33 ft (10 m) from the vehicle. (The effective
distance depends upon the conditions around
the vehicle.) As many as 4 Intelligent Keys can
be used with one vehicle. For information
concerning the purchase and use of additional
Intelligent Keys, contact a NISSAN dealer.
The lock and unlock buttons will not operate when:
.
the distance between the Intelligent Key and
the vehicle is over 33 ft (10 m) .
. the Intelligent Key battery is discharged.
After locking with the remote keyless entry
function, pull the door handle to make sure the
doors are securely locked.
The LOCK/UNLOCK operating range varies
depending on the environment. To securely
operate the lock and unlock buttons, approach
the vehicle to about 3 ft (1 m) from the door.
SPA2252A
Type A
SPA2436
Type B
REMOTE KEYLESS ENTRY SYSTEM
Condition:

Black plate (170,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-18Pre-driving checks and adjustments
button*2again until the window opens
completely.
The door windows can be opened or closed by
turning the mechanical key in a door lock. (See
“Doors” earlier in this section.)
Opening/closing lift gate (if so equipped)GUID-7A0EC3F3-A0FF-43A5-983C-6F30EE025AB41. Push the power lift gatebutton*3
for more than 1 second.
2. The lift gate will automatically open.
The hazard indicator flashes 4 times and the
outside chime sounds for approximately 3
seconds.
To close the lift gate, push the power lift gate
button*3.
The lift gate will automatically close.
If the power lift gate
button*3is pushed
while the lift gate is being opened or closed, the
lift gate will reverse.
The power lift gate
button*3cannot be
operated when the ignition switch is in the ON
position.
Using panic alarmGUID-0EEA2C46-8F73-4264-8914-B8CE095E8B5CIf you are near your vehicle and feel threatened,
you can activate the alarm according to the
following procedure to call attention.
1. Push the PANIC
button*4for more
than 1 second.
2. The theft warning alarm will sound and the headlights will flash for 25 seconds.
3. The panic alarm stops under either of the following conditions.
.It has run for 25 seconds, or.Any of the buttons is pushed. (Note: thePANIC
button*4should be
pushed for more than 1 second.)
Opening trunk lid (CrossCabriolet mod-
els)
GUID-87B7F82C-E682-4BF3-BE6B-52CC949856EB1. Push the TRUNKbutton*5on the
Intelligent Key for more than 1 second.
2. The trunk will unlatch.
3. Raise the trunk lid to open the trunk.
Setting hazard indicator and horn modeGUID-0B7C4602-8422-4E4E-A11F-E789553B0A3DThis vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
In hazard indicator and horn mode, when the
LOCK
button*1is pushed, the hazard
indicator flashes twice and the horn chirps once.
When the UNLOCK
button*2is pushed,
the hazard indicator flashes once.
If horns are not necessary, the system can be
switched to the hazard indicator mode.
In hazard indicator mode, when the LOCK
button*1is pushed, the hazard indicator
flashes twice. When the UNLOCK
button
*2is pushed, neither the hazard indicator nor
the horn operates.
Condition:

Black plate (172,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-20Pre-driving checks and adjustments
GUID-EFCA6993-4C66-4840-8CB7-A8AB3D34E97F
SPA2437
1.Pull the hood lock release handle*1
located below the instrument panel; the
hood will then spring up slightly.
2. Pull the lever
*2up at the front of the hood
with your fingertips and raise the hood.
3. When closing the hood, slowly close the hood down and make sure it locks into
place.
WARNING
.Make sure the hood is completely
closed and latched before driving.
Failure to do so could cause the
hood to fly open and result in an
accident.
. If you see steam or smoke coming
from the engine compartment, to
avoid injury do not open the hood.
GUID-4BA01BDD-7B7E-4674-BC74-CD9F5511DABB
WARNING
.Always be sure the lift gate has
been closed securely to prevent it
from opening while driving.
. Do not drive with the lift gate open.
This could allow dangerous exhaust
gases to be drawn into the vehicle.
See “Exhaust gas (carbon monox-
ide)” in the “5. Starting and driving”
section of this manual.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols. Unattended children could
become involved in serious acci-
dents.
. Always be sure that hands and feet
are clear of the door frame to avoid
injury while closing the lift gate.
HOOD LIFT GATE (Hardtop models)
Condition:

Black plate (175,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
The hazard flashes 4 times and the outside
chime sounds when the lift gate starts closing.
Reverse functionGUID-28EE2E95-2E6D-4231-A853-225C012F131BThe power lift gate will reverse immediately if
one of the following actions is performed during
power open or power close.
.pushing the power lift gate switch
*Aon
the instrument panel
. pushing the lift gate switch
*Don the lower
part of the lift gate
. pushing the lift gate button
*Con
the Intelligent Key.
The outside chime sounds when the lift gate
starts to reverse.
The power lift gate button
*Con the
Intelligent Key cannot be operated when the
ignition switch is in the ON position.
Auto reverse functionGUID-588A601D-27B2-48E9-8FDE-883DF425CE62The auto-reverse function enables the lift gate to
automatically reverse when something is caught
in the lift gate as it is opening or closing. When
the control unit detects an obstacle, the lift gate
will reverse and return to the full open or full
close position.
If a second obstacle is detected, the lift gate
motion will stop and the drive motor will
disengage. The lift gate will enter the manual mode.
A pinch sensor is mounted on each side of the
lift gate. If an obstacle is detected by the pinch
sensor during power close, the lift gate will
reverse and return to the full open position
immediately.
NOTE:
If the pinch sensor is damaged or removed,
the power close function will not operate.
WARNING
There is a small distance immediately
before the closed position that cannot
be detected. Make sure that all passen-
gers keep their hands, etc., clear from
the lift gate opening before closing the
lift gate.
Manual modeGUID-2D066900-C91C-4239-8B7E-587EF875F5E6If power operation is not available, the lift gate
can be operated manually. Power operation may
not be available if multiple obstacles have been
detected in a single power cycle or if the battery
voltage is low. When the power lift gate main
switch is in the OFF position, the lift gate can be
opened manually by pushing the lift gate opener
switch. If the power lift gate opener switch ispushed during power open or close, the power
operation will be canceled and the lift gate can
be operated manually.
Pre-driving checks and adjustments3-23
Condition:

Black plate (177,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA1915
LIFT GATE RELEASEGUID-1D614743-17EC-4673-B778-F929F5E10CB9If the lift gate cannot be opened due to a
discharged battery, follow these steps.
1. Remove the cover inside of the lift gate witha suitable tool.
2. Move the lever toward the direction
*Aas
illustrated to open the lift gate.
Have the vehicle checked by a NISSAN dealer.
GUID-2C264EE5-CF00-4D99-8287-BE0FA9532E1E
WARNING
. Do not drive with the trunk lid open.
This could allow dangerous exhaust
gases to be drawn into the vehicle.
See “Exhaust gas (carbon monox-
ide)” in the “5. Starting and driving”
section of this manual.
. Closely supervise children when
they are around cars to prevent
them from playing and becoming
locked in the trunk where they could
be seriously injured. Keep the car
locked, with the trunk closed, when
not in use, and prevent children’s
access to Intelligent Keys.
SPA2868
TRUNK LID RELEASE SWITCHGUID-3E3F75C6-3DEC-4CB3-AB7F-5D7232A3354CThe trunk lid release switch*Ais located on
the instrument panel.
To open the trunk lid, push the release switch
down as illustrated. To close, push the trunk lid
down.
Pre-driving checks and adjustments3-25
TRUNK LID (CrossCabriolet models)
Condition:

Black plate (179,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
you.
See “Keys” earlier in this section.
To connect the power to the trunk lid, push the
switch to the ON
*Bposition.
SPA2870
INTERIOR TRUNK LID RELEASEGUID-76617E49-69A3-42A3-B4CE-6BA318A11DE5
WARNING
Closely supervise children when they
are around cars to prevent them from
playing and becoming locked in the
trunk where they could be seriously
injured. Keep the car locked, with the
trunk lid securely latched, when not in
use, and prevent children’s access to
Intelligent Keys.The interior trunk lid release mechanism allows
opening of the trunk lid in the event that people
become locked inside the trunk or in the event of
the loss of electrical power such as a dis-
charged battery.
Releasing inside the trunkGUID-AF4D5EDF-174E-4F6F-B198-B456683E28BDTo open the trunk lid from the inside, pull the
release handle
*1until the lock releases and
push up on the trunk lid. The release lever is
made of a material that glows in the dark after a
brief exposure to ambient light.
The handle is located on the back of the trunk lid
as illustrated.
Pre-driving checks and adjustments3-27
Condition:

Black plate (181,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
Be sure to follow the operating instructions, and
all the warnings and cautions in this section.
Improper operation of the top could cause
a system malfunction, damage, or dete-
rioration of the top material and related
parts.
SPA2873
WARNING
.Do not operate the top when there
is not enough clearance behind the
vehicle. Someone could become
trapped between the top storage
lid and another object (for example
a wall) which could result in serious
injury.
. Park the vehicle in a safe and level
place and apply the parking brake.
. Do not operate the top in a strong
wind. It could be blown by the wind,
striking someone or damaging the top.
. Do not allow anyone to stand up or
extend any portion of their body out
of the opening while the vehicle is in
motion or while the top is being
operated.
. In an accident you could be thrown
from the vehicle with an open top.
Always use seat belts and proper
child restraints.
Pre-driving checks and adjustments3-29
Condition:

Black plate (183,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVP0045X
WARNING
.Never install a cover or film (for
example window tint) on the sky-
light glass. This may cause the dual
pop-up roll bars to operate impro-
perly and could result in serious
injury or death in the event of a
rollover. (see “Dual pop-up roll bar
system (CrossCabriolet models)” in
the “1. Safety — Seats, seat belts
and supplemental restraint system”
section.)
CAUTION
.Do not operate the top when the
temperature is below 328F (08C) .
This may result in damage to the
top material or operating system.
. Remove water drops, snow, ice or
sand from the top, and dry the
surface of the top completely before
opening it.
. Do not open the top when it is wet
or damp. This may cause interior
water damage, stains or mildew on
the top material.
. Be sure to turn off the rear window
defroster switch. Never turn it on
while the top is being operated or
fully opened. The heat may damage
the top material.
SPA2691
CAUTION
.Do not place any objects between
the top cloth and the structure.
Doing so could interfere with top
operation and cause damage to the
top operating system or the objects.
. Do not place anything on the top,
rear parcel shelf, inner flaps and
trunk lid. Even small items may
interfere with the top operation
and could cause damage to the top
or the vehicle body.
Pre-driving checks and adjustments3-31
Condition:

Black plate (184,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-32Pre-driving checks and adjustments
.Do not place anything in the top
storage area. The top will not fit
there properly, and this could da-
mage the top and/or the vehicle
body.
. Do not sit or place anything on the
top, rear parcel shelf, inner flaps,
storage lid and trunk lid, especially
when the top is being operated. The
top may be damaged.
. Do not drive the vehicle with the top
partially opened. Always make sure
the top is either fully opened or
closed before driving.
. Secure items so that they cannot be
blown from the vehicle while driving
with the top open.
. Do not operate the top manually
except for emergency cases. Manual
operation may damage the top.
. Be sure to fully open or fully close
the top. Do not release the switch
half way through the roof opening
or closing process. If the top is only
partially opened, significant da-
mage to the top could occur.
. Do not operate the top if the dual
pop-up roll bars have been acti- vated. Extended dual pop-up roll
bars may interfere with top opera-
tion and could cause damage to the
top or the vehicle body.
Make sure the trunk lid is securely closed before
operating the top.
SPA2874
WHEN OPERATING THE TOPGUID-9783AAEB-D9EE-4150-9CAA-F03901BE51C6
WARNING
Keep hands and other parts of the body
away from moving parts such as the
top, storage lid, inner flap
*Aand
power windows.
Condition:

Black plate (190,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-38Pre-driving checks and adjustments
IF THE TOP DOES NOT OPEN OR
CLOSE ELECTRICALLY
GUID-17B75AAD-7BCD-4553-9A36-FB3FA5E49CAFIf you cannot operate the soft top with the
operating switch, first check whether all the
following operating conditions are met.
.Vehicle is stopped
. Ignition switch is ON (Run the engine when
operating the top.)
. The trunk is closed
. The selector lever is in a position other than
the R (Reverse) position
. The luggage cover is pulled out and hooked
so that the roof storage area is separated
from the trunk.
If the top still does not move under the above
conditions or has any system malfunction, see a
NISSAN dealer as soon as possible. When you
must close the top by yourself, in the event of
emergency or when an immediate dealer service
is not available, close the top manually accord-
ing to the procedures shown in this section.
When closing the soft top manually:
. Move the vehicle to a safe place, away from
traffic.
. Two people should perform this procedure,
as some of the top parts are extremely
heavy.
The top cannot be opened manually.
WARNING
. Do not drive with the top partially
opened.
. If the top cannot be operated prop-
erly, see a NISSAN dealer as soon
as possible to have your vehicle
checked.
CAUTION
The storage lid is extremely heavy. The
storage lid should be manually opened
or closed by two people.
1. Open the trunk lid. In the event of a
discharged battery, the secondary trunk
release mechanism should be operated.
(See “Trunk lid (CrossCabriolet models)”
earlier in this section.)
2. Open the top storage lid.JVP0036X
a. Remove the trunk light*1.
b. Remove the lower trim clips
*3and
remove the upper and lower trim pieces
*2.
c. Remove the two luggage cover hooks
*4
on the left and right side of the trunk.
Then disconnect the connector
*5on
the left side luggage cover hook.
d. Remove the clips
*6behind the luggage
cover hooks.
Condition: