warning NISSAN MURANO 2013 2.G Owners Manual

Black plate (360,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-14Starting and driving
SSD0837
INTELLIGENT KEY BATTERY DIS-
CHARGE
GUID-B0FA47F4-2F8B-42AE-95A0-B8BDCC855CA4If the battery of the Intelligent Key is almost
discharged, the guide light
*Bof the key port
*Ablinks and the indicator appears on the dot
matrix liquid crystal display. (See “Dot matrix
liquid crystal display” in the “2. Instruments and
controls” section.)
In this case, inserting the Intelligent Key into the
port
*Aallows you to start the engine. Make
sure that the key ring side faces backward as
illustrated. Insert the Intelligent Key in the port
until it is latched and secured.
To remove the Intelligent Key from the port, push
the ignition switch to the OFF position and pull the Intelligent Key out of the port.
NOTE:
The key port does not charge the key
battery. If you see the low battery indicator
in the dot matrix liquid crystal display,
replace the battery as soon as possible.
(See “Intelligent Key battery replacement”
in the “8. Maintenance and do-it-yourself”
section.)
CAUTION
.
Never place anything except the
Intelligent Key in the key port. Doing
so may cause damage to the equip-
ment.
. Make sure the Intelligent Key is in
the correct direction when inserting
it to the key port. The engine may
not start if it is in the incorrect
direction.
. Remove the Intelligent Key from the
key port after the ignition switch is
pushed to the OFF position.
GUID-147FB3A5-0560-4EED-8FD9-82CD1174F15F.Make sure the area around the vehicle is
clear.
. Check fluid levels such as engine oil, cool-
ant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
. Check that all windows and lights are clean.
. Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
. Lock all doors.
. Position seats and adjust head restraints/
headrests.
. Adjust inside and outside mirrors.
. Fasten seat belts and ask all passengers to
do likewise.
. Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (See “Warning/indicator lights and
audible reminders” in the “2. Instruments
and controls” section.)
BEFORE STARTING THE ENGINE
Condition:

Black plate (362,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-16Starting and driving
GUID-874DAAA4-503F-461F-8A66-BEEC6486BBB0CONTINUOUSLY VARIABLE TRANS-
MISSION (CVT)
GUID-ACCD68EB-D536-48ED-BBB3-82DB1D8F06BAThe Continuously Variable Transmission (CVT)
in your vehicle is electronically controlled to
produce maximum power and smooth operation.
The recommended operating procedures for this
transmission are shown on the following pages.
Follow these procedures for maximum vehicle
performance and driving enjoyment.
Engine power may be automatically re-
duced to protect the CVT if the engine
speed increases quickly when driving on
slippery roads or while being tested on
some dynamometers.
Starting the vehicleGUID-35972EF7-F09E-4D7E-99A4-08117777767B1. After starting the engine, fully depress thefoot brake pedal before moving the selector
lever out of the P (Park) position.
This CVT is designed so that the foot
brake pedal must be depressed before
shifting from P (Park) to any driving
position while the ignition switch is in
the ON position.
The selector lever cannot be moved out
of the P (Park) position and into any of
the other positions if the ignition
switch is pushed to the LOCK, OFF or
ACC position. 2. Keep the foot brake pedal depressed and
move the selector lever to a driving position.
3. Release the parking brake and foot brake pedal, and then gradually start the vehicle in
motion.
WARNING
.Do not depress the accelerator
pedal while shifting from P (Park)
or N (Neutral) to R (Reverse) , D
(Drive) or L (Low) position. Always
depress the brake pedal until shift-
ing is completed. Failure to do so
could cause you to lose control and
have an accident.
. Cold engine idle speed is high, so
use caution when shifting into a
forward or reverse gear before the
engine has warmed up.
. Never shift to P (Park) or R (Re-
verse) while vehicle is moving. Fail-
ure to do so could cause you to lose
control and have an accident.
CAUTION
.Except in an emergency, do not shift
to the N (Neutral) position while
driving. Coasting with the transmis-
sion in the N (Neutral) position may
cause serious damage to the trans-
mission.
. When stopping the vehicle on an
uphill grade, do not hold the vehicle
by depressing the accelerator pedal.
The foot brake should be used for
this purpose.
. Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.
DRIVING THE VEHICLE
Condition:

Black plate (363,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSD0691
To move the selector lever,
: Push the button*Awhile depressing the
brake pedal.
: Push the button*A.
: Just move the selector lever.
ShiftingGUID-D5026A04-B5E5-49C1-B727-309E2651B4AEAfter starting the engine, fully depress the brake
pedal, push the selector lever button and move
the selector lever from the P (Park) position to
any of the desired shift positions.
WARNING
Apply the parking brake if the selector
lever is in any position while the engine
is not running. Failure to do so could
cause the vehicle to move unexpectedly
or roll away and result in serious
personal injury or property damage.
CAUTION
Use the P (Park) or R (Reverse) position
only when the vehicle is completely
stopped.
P (Park):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Use this selector position when the vehicle is
parked or when starting the engine. Make sure
the vehicle is completely stopped. The brake
pedal must be depressed and the selector
lever button pushed in to move the selec-
tor lever from N (Neutral) or any drive
position to P (Park) . Apply the parking brake.
When parking on a hill, apply the parking brake
first, then move the selector lever to the P (Park)
position. R (Reverse):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Use this position to back up. Make sure the
vehicle is completely stopped before selecting
the R (Reverse) position.
The brake pedal
must be depressed and the selector lever
button pushed in to move the selector
lever from P (Park) , N (Neutral) or any
driving position to R (Reverse) .
N (Neutral):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Neither forward nor reverse gear is engaged.
The engine can be started in this position. You
may shift to N (Neutral) and restart a stalled
engine while the vehicle is moving.
D (Drive):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Use this position for all normal forward driving.
L (Low):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Use this position for maximum engine braking on
steep downhill gradients/climbing steep slopes
and whenever approaching sharp bends. Do not
use the L position in any other circumstances.
Starting and driving5-17
Condition:

Black plate (364,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-18Starting and driving
SSD0692
Overdrive (O/D) OFF switchGUID-8A3D61C2-25AC-4088-A419-A1EAB3D4657FWhen the O/D OFF switch is pushed with the
selector lever in the D (Drive) position, the
indicator light in the instrument panel illuminates.
Use the overdrive off mode when you need
improved engine braking.
To turn off the overdrive off mode, push the O/D
OFF switch again. The
indicator light will
turn off.
Each time the engine is started, or when the
selector lever is shifted to any position other
than the D (Drive) position, the overdrive off
mode will be automatically turned off.
Accelerator downshift — In D position —GUID-CD19E66D-4772-4785-B00D-BC9BC6AC4E04For passing or hill climbing, fully depress the
accelerator pedal to the floor. This shifts the
transmission down into a lower gear, depending
on the vehicle speed.
High fluid temperature protection modeGUID-FE0DB0A0-F4AF-44F6-8609-E1599FEA814DThis transmission has a high fluid temperature
protection mode. If the fluid temperature be-
comes too high (for example, when climbing
steep grades in high temperature with heavy
loads, such as when towing a trailer), engine
power and, under some conditions, vehicle
speed will be decreased automatically to reduce
the chance of transmission damage. Vehicle
speed can be controlled with the accelerator
pedal, but the engine and vehicle speed may be
limited.
Fail-safeGUID-CA9C7C97-9363-4621-960F-9DED536408A1If the vehicle is driven under extreme
conditions, such as excessive wheel spin-
ning and subsequent hard braking, the
fail-safe system may be activated. The MIL
may illuminate to indicate the fail-safe
mode is activated. (See “Malfunction In-
dicator Light (MIL)” in the “2. Instruments
and controls” section.) This will occur even
if all electrical circuits are functioning
properly. In this case, place the ignition switch in the OFF position and wait for 10
seconds. Then place the ignition switch
back in the ON position. The vehicle should
return to its normal operating condition. If
it does not return to its normal operating
condition, have a NISSAN dealer check the
transmission and repair if necessary.
WARNING
When the high fluid temperature pro-
tection mode or fail-safe operation
occurs, vehicle speed may be gradually
reduced. The reduced speed may be
lower than other traffic, which could
increase the chance of a collision. Be
especially careful when driving. If ne-
cessary, pull to the side of the road at a
safe place and allow the transmission
to return to normal operation, or have it
repaired if necessary.
Condition:

Black plate (365,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SSD0693
Shift lock releaseGUID-4E0BBA67-0709-45D4-82B6-4589F6D64379If the battery charge is low or discharged, the
selector lever may not be moved from the P
(Park) position even with the brake pedal
depressed and the selector lever button pushed.
To move the selector lever, perform the following
procedure:
1. Push the ignition switch to the OFF or LOCKposition.
2. Apply the parking brake.
3. Remove the shift lock release cover
*A
using a suitable tool. 4. Push down the shift lock release
*Busing a
suitable tool.
5. Push the selector lever button
*Cand move
the selector lever to the N (Neutral) position
*Dwhile holding down the shift lock
release.
The vehicle may be moved to the desired
location.
Replace the removed shift lock release cover
after the operation.
If the selector lever cannot be moved out of the
P (Park) position, have a NISSAN dealer check
the CVT system as soon as possible.
WARNING
If the selector lever cannot be moved
from the P (Park) position while the
engine is running and the brake pedal
is depressed, the stop lights may not
work. Malfunctioning stop lights could
cause an accident injuring yourself and
others.
GUID-E081E1F7-54B4-4901-B654-AF785D4BF47C
WARNING
. Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
. Do not release the parking brake
from outside the vehicle.
. Do not use the gear shift in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged.
. Do not leave children unattended in
a vehicle. They could release the
parking brake and cause an acci-
dent.
Starting and driving5-19
PARKING BRAKE
Condition:

Black plate (366,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-20Starting and driving
SPA2331
To apply:Fully depress the parking brake pedal
*1.
To release:
1. Firmly apply the foot brake
*2.
2. Depress the parking brake pedal
*1and
the parking brake will be released.
3. Before driving, be sure the brake warning light goes out.
GUID-EAE4D145-2304-42BA-802A-31B01291BFE6The Blind Spot Warning (BSW) system helps
alert the driver of other vehicles in adjacent lanes
when changing lanes.
The Lane Departure Warning (LDW) system
helps alert the driver when the vehicle is
traveling close to either the left or the right of a
traveling lane.
JVS0152X
The BSW/LDW systems use the RearView
Monitor camera unit
*1with automatic washer
and blower.
WARNING
. The BSW system is not a replace-
ment for proper driving procedure
and is not designed to prevent
contact with vehicles or objects.
When changing lanes, always use
the side and rear mirrors and turn
and look in the direction you will
move to ensure it is safe to change
lanes. Never rely solely on the BSW
BLIND SPOT WARNING (BSW)/
LANE DEPARTURE WARNING (LDW)
SYSTEMS (if so equipped)
Condition:

Black plate (367,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
system.
. The LDW system is only a warning
device to help inform the driver of a
potential unintended lane depar-
ture. It will not steer the vehicle or
prevent loss of control. It is the
driver’s responsibility to stay alert,
drive safely, keep the vehicle in the
traveling lane, and be in control of
the vehicle at all times.
. The camera unit may not function
properly under the following condi-
tions:
— When towing a trailer.
— When strong light enters the
camera unit. (for example, light
directly shines on the rear of the
vehicle at sunrise or sunset.)
— When ambient brightness changes suddenly. (for example,
when the vehicle enters or exits
a tunnel or passes under a
bridge.)
. If the camera lens is excessively
dirty, the automatic washer may not
be able to completely clean the lens.
This could result in the camera not
detecting vehicles or lane markers. .
Excessive noise (for example, audio
system volume, open vehicle win-
dow) will interfere with the chime
sound, and it may not be heard.
SSD1086
Blind Spot Indicator light
SSD1029
BSW light (orange, green)
Starting and driving5-21
Condition:

Black plate (369,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVS0159X
SSD0885
Example
Perform the following steps to enable or disable
the BSW system.
1. Push the SETTING
*1button and highlight
the “Driver Assistance” key on the display
using the multi-function controller. Then
push the ENTER
*2button.
JVH0345X
2. Highlight the “Blind Spot Warning” key,
select ON (enabled) or OFF (disabled) and
push the ENTER
*2button.
Starting and driving5-23
Condition:

Black plate (370,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-24Starting and driving
SSD1156
Warning systems switch
The warning systems switch is used to tem-
porarily turn off the warning systems (Lane
Departure Warning (LDW) and Blind Spot
Warning (BSW) systems) that are activated
using the settings menu.
WARNING
.The camera unit may not be able to
detect when certain objects are
present such as:
— Pedestrians, bicycles, animals — Some types of small vehicles
such as motorcycles and very
short length vehicles
— Oncoming vehicles
— A vehicle approaching rapidly from behind. (See “BSW driving
situations” later in this section.)
— A vehicle which your vehicle overtakes rapidly. (See “BSW
driving situations” later in this
section.)
— A vehicle that merges or changes lanes rapidly directly
next to your vehicle.
. The camera unit may not be able to
detect properly when your vehicle
travels beside the middle section of
a vehicle with long wheelbase (for
example, trailer truck, semi-trailer,
tractor) .
. The camera detection zone is de-
signed based on a standard lane
width. When driving in a wider lane,
the camera unit may not detect
vehicles in an adjacent lane. When
driving in a narrow lane, the camera
unit may detect vehicles driving two lanes away.
. The camera unit is designed to
ignore most stationary objects,
however objects such as guardrails,
walls, foliage and parked vehicles
may occasionally be detected. This
is a normal operating condition.
. The camera unit may detect the
reflected image of vehicles or road-
side objects that are not actually in
the detection zone, especially when
the road is wet.
Condition:

Black plate (374,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
5-28Starting and driving
JVH0345X
2. Highlight the “Lane Departure Warning” key,select ON (enabled) or OFF (disabled) and
push the ENTER
*2button.
SSD1156
Warning systems switch
The warning systems switch is used temporarily
turn off the warning systems (Lane Departure
Warning (LDW) and Blind Spot Warning (BSW)
systems) that are activated using the settings
menu.
WARNING
.The camera unit may not be able to
detect properly under the following
conditions:
— On roads where there are multi-
ple parallel lane markers; lane
markers that are faded or not painted clearly; yellow painted
lane markers; nonstandard lane
markers; or lane markers cov-
ered with water, dirt, snow, etc.
— On roads where the discontin- ued lane markers are still de-
tectable.
— On roads where there are sharp curves.
— On roads where there are shar- ply contrasting objects, such as
shadows, snow, water, wheel
ruts, seams or lines remaining
after road repairs. (The LDW
system could detect these items
as lane markers.)
— On roads where the traveling lane merges or separates.
— When the vehicle’s traveling di- rection does not align with the
lane marker.
— When the road surface is very dark due to weak ambient light
or impaired tail lamp.
. When driving on a curved road,
warning will be late on the outside
Condition: