light NISSAN MURANO 2013 2.G Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2013, Model line: MURANO, Model: NISSAN MURANO 2013 2.GPages: 507, PDF Size: 4.61 MB
Page 147 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (145,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SIC3250
PERSONAL LIGHTS (Hardtop models)GUID-649CAF7C-2CCF-4E76-A1BD-9F34B3E94A95
RearGUID-0958BB58-F974-4165-8A79-D4E6DD15AACDPush the button as](/img/5/332/w960_332-146.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (145,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SIC3250
PERSONAL LIGHTS (Hardtop models)GUID-649CAF7C-2CCF-4E76-A1BD-9F34B3E94A95
RearGUID-0958BB58-F974-4165-8A79-D4E6DD15AACDPush the button as")
Black plate (145,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SIC3250
PERSONAL LIGHTS (Hardtop models)GUID-649CAF7C-2CCF-4E76-A1BD-9F34B3E94A95
RearGUID-0958BB58-F974-4165-8A79-D4E6DD15AACDPush the button as illustrated to turn the light on
or off.
SIC4239
INTERIOR LIGHT CONTROL SWITCHGUID-2A6055BA-7B37-4FE4-B397-77EF5A05A796The interior light control switch has three
positions: ON, DOOR and OFF.
ON positionGUID-7462AA90-5FAE-4F84-925A-24F0133E09B3When the switch is in the ON position*1the
map lights and rear personal lights will illumi-
nate.
DOOR positionGUID-2534F567-EC7E-4D89-9E58-CCFFC0DDC2B3When the switch is in the DOOR position*2,
the map lights and rear personal lights will
illuminate under the following conditions:
. ignition switch is switched to the LOCK
position — remain on for about 15 seconds.
. doors are unlocked by pushing the UN-
LOCK button on the Intelligent Key or door
handle request switch with the ignition
switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened with the ignition switch
in the ACC or ON position
— remain on while the door is opened.
When the door is closed, the lights go
off.
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
Models with color display:
When the auto interior illumination is set to the
OFF position (see “Vehicle information and
settings” in the “4. Monitor, heater, air condi-
tioner, audio, phone and voice recognition
systems” section) , the lights will illuminate under
the following condition:
. any door is opened with the ignition switch
in any position
Instruments and controls2-61
Condition:
Page 148 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (146,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-62Instruments and controls
— remain on while the door is opened.When the door is closed, the lights go
off.
OFF positionGUID-2E9E6196-2FCF-49](/img/5/332/w960_332-147.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (146,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-62Instruments and controls
— remain on while the door is opened.When the door is closed, the lights go
off.
OFF positionGUID-2E9E6196-2FCF-49")
Black plate (146,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-62Instruments and controls
— remain on while the door is opened.When the door is closed, the lights go
off.
OFF positionGUID-2E9E6196-2FCF-4993-83DD-8C4EF8E70D73When the switch is in the OFF position*3, the
lights will not illuminate, regardless of the
condition.
CAUTION
Do not use for extended periods of time
with the engine stopped. This could
result in a discharged battery.
GUID-010F00F5-89B1-468A-B28C-562B74BD8B74
SIC3599
Map lights
The mood lights*Alocated in the following
positions will illuminate whenever the headlight
switch is in the
orposition.
. next to the map lights
. under the instrument panel
. under the driver’s power window switch
The brightness of the mood lights can be
adjusted with the illumination control buttons.
See “Instrument brightness control” earlier in
this section.
GUID-6E431C2A-BCAB-4ED8-9FA7-03F14AE124F0
SIC2064
The light on the vanity mirror will turn on when
the cover on the vanity mirror is opened.
When the cover is closed, the light will turn off.
The lights will turn off after a period of
time when the lights remain illuminated to
prevent the battery from becoming dis-
charged.
MOOD LIGHTS (Hardtop models) VANITY MIRROR LIGHTS
Condition:
Page 149 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (147,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-AC16BAD8-F320-4304-996B-A0D05319728A
SIC2131A
When the switch is in the ON position*1, the
light illuminates while the lift gate is opened.](/img/5/332/w960_332-148.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (147,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-AC16BAD8-F320-4304-996B-A0D05319728A
SIC2131A
When the switch is in the ON position*1, the
light illuminates while the lift gate is opened.")
Black plate (147,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-AC16BAD8-F320-4304-996B-A0D05319728A
SIC2131A
When the switch is in the ON position*1, the
light illuminates while the lift gate is opened.
When the lift gate is closed, the light will turn off.
When the switch is in the OFF position
*2, the
light will turn off.
The lights will turn off after a period of
time when the light remain illuminated to
prevent the battery from becoming dis-
charged.
GUID-F7665349-183E-4013-AA39-F31226267085The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the light
will turn off.
The light will also turn off after a period of
time when the light remains illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.GUID-55E56F2F-00B7-4A2E-969B-A4422F852328The HomeLink®Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.
HomeLink
®Universal Transceiver:
. Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
. Is powered by your vehicle’s battery. No
separate batteries are required. If the
vehicle’s battery is discharged or is dis-
connected, HomeLink
®will retain all pro-
gramming.
When the HomeLink
®Universal Transcei-
ver is programmed, retain the original
transmitter for future programming proce-
dures (Example: new vehicle purchases) .
Upon sale of the vehicle, the programmed
HomeLink
®Universal Transceiver buttons
should be erased for security purposes.
For additional information, refer to “Pro-
gramming HomeLink
®” later in this sec-
tion.
Instruments and controls2-63
CARGO LIGHTS (Hardtop models) TRUNK LIGHT (CrossCabriolet
models)HomeLink®UNIVERSAL
TRANSCEIVER (if so equipped)
Condition:
Page 150 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (148,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-64Instruments and controls
WARNING
.Do not use the HomeLink®Universal
Transceiver with any garage door
opener that lacks safety stop and
rever](/img/5/332/w960_332-149.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (148,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-64Instruments and controls
WARNING
.Do not use the HomeLink®Universal
Transceiver with any garage door
opener that lacks safety stop and
rever")
Black plate (148,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-64Instruments and controls
WARNING
.Do not use the HomeLink®Universal
Transceiver with any garage door
opener that lacks safety stop and
reverse features as required by
federal safety standards. (These
standards became effective for
opener models manufactured after
April 1, 1982) . A garage door opener
which cannot detect an object in the
path of a closing garage door and
then automatically stop and reverse,
does not meet current federal safety
standards. Using a garage door
opener without these features in-
creases the risk of serious injury or
death.
. During the programming procedure
your garage door or security gate
will open and close (if the transmit-
ter is within range) . Make sure that
people or objects are clear of the
garage door, gate, etc. that you are
programming.
. Your vehicle’s engine should be
turned off while programming the
HomeLink
®Universal Transceiver.
Do not breathe exhaust gases; they contain colorless and odorless car-
bon monoxide. Carbon monoxide is
dangerous. It can cause uncon-
sciousness or death.
PROGRAMMING HomeLink®GUID-D8C5E61E-41B3-4673-B29E-956822CDD882If you have any questions or are having difficulty
programming your HomeLink®buttons, refer to
the HomeLink®web site at: www.homelink.com
or call 1-800-355-3515.
NOTE:
It is also recommended that a new battery
be placed in the hand-held transmitter of
the device being programmed to
HomeLink
®for quicker programming and
accurate transmission of the radio-fre-
quency.
1. Position the end of your hand-held transmit- ter 1-3 in (26-76 mm) away from the
HomeLink
®surface, keeping the HomeLink®
indicator light*1in view.
JVI0428X
2. Using both hands, simultaneously press and
hold the desired HomeLink®button and
handheld transmitter button. DO NOT re-
lease until the HomeLink
®indicator light*1
flashes slowly and then rapidly. When the
indicator light flashes rapidly, both buttons
may be released. (The rapid flashing indi-
cates successful programming.)
NOTE:
Some devices to be programmed may
require you to replace Step 2 with the
cycling procedure noted in the “Pro-
gramming HomeLink
®for Canadian
customers and gate openers”.
Condition:
Page 151 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (149,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVI0429X
3. Press and hold the programmed HomeLink®
button and observe the indicator light..If the indicator light*1is solid/contin-
uous, progr](/img/5/332/w960_332-150.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (149,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVI0429X
3. Press and hold the programmed HomeLink®
button and observe the indicator light..If the indicator light*1is solid/contin-
uous, progr")
Black plate (149,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
JVI0429X
3. Press and hold the programmed HomeLink®
button and observe the indicator light..If the indicator light*1is solid/contin-
uous, programming is complete and your
device should activate when the
HomeLink
®button is pressed and re-
leased.
.If the indicator light*1blinks rapidly for
two seconds and then turns to a solid/
continuous light, continue with Steps 4-6
for a rolling code device. A second
person may make the following steps
easier. Use a ladder or other device. Do
not stand on your vehicle to perform the
next steps. 4. At the receiver located on the garage door
opener motor in the garage, locate the
“learn” or “smart” button (the name and
color of the button may vary by manufacturer
but it is usually located near where the
hanging antenna wire is attached to the
unit). If there is difficulty locating the button,
reference the garage door opener’s manual.
5. Press and release the “learn” or “smart” button.
NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate
the next step.
6. Return to the vehicle and firmly press and hold the programmed HomeLink
®button for
two seconds and release. Repeat the
“press/hold/release” sequence up to 3
times to complete the programming pro-
cess. HomeLink
®should now activate your
rolling code equipped device.
7. If you have any questions or are having difficulty programming your HomeLink
®but-
tons, refer to the HomeLink®web site at:
www.homelink.com or call 1-800-355-
3515.
PROGRAMMING HomeLink®FOR CA-
NADIAN CUSTOMERS AND GATE
OPENERS
GUID-8263D00C-5505-4CBD-9B5E-CB372155C17ACanadian radio-frequency laws require trans-
mitter signals to “time-out” (or quit) after several
seconds of transmission – which may not be
long enough for HomeLink
®to pick up the signal
during programming. Similar to this Canadian
law, some U.S. gate operators are designed to
“time-out” in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator or garage door
opener by using the “Programming HomeLink
®”
procedures, replace “Programming HomeLink®”
Step 2 with the following:
NOTE:
When programming a garage door opener,
etc., unplug the device during the “cycling”
process to prevent possible damage to the
garage door opener components.
Step 2: Using both hands, simultaneously press
and hold the desired HomeLink
®button and the
hand-held transmitter button. During program-
ming, your hand-held transmitter may automati-
cally stop transmitting. Continue to press and
hold the desired HomeLink
®button while you
press and re-press (“cycle”) your hand-held
transmitter every two seconds until the fre-
quency signal has been learned. The HomeLink
®
Instruments and controls2-65
Condition:
Page 152 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (150,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-66Instruments and controls
indicator light will flash slowly and then rapidly
after several seconds upon successful program-
ming.DO NOT releas](/img/5/332/w960_332-151.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (150,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-66Instruments and controls
indicator light will flash slowly and then rapidly
after several seconds upon successful program-
ming.DO NOT releas")
Black plate (150,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-66Instruments and controls
indicator light will flash slowly and then rapidly
after several seconds upon successful program-
ming.DO NOT release until the HomeLink
®
indicator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both
buttons may be released. The rapid flashing
indicates successful programming.
Proceed with “Programming HomeLink
®” step 3
to complete.
Remember to plug the device back in when
programming is completed.
OPERATING THE HomeLink®UNIVER-
SAL TRANSCEIVER
GUID-19BE850B-BBDC-470B-9850-DE6B57FF6B98The HomeLink®Universal Transceiver, after it is
programmed, can be used to activate the
programmed device. To operate, simply press
and release the appropriate programmed
HomeLink
®Universal Transceiver button. The
amber indicator light will illuminate while the
signal is being transmitted.
For convenience, the hand-held transmitter of
the device may also be used at any time.
PROGRAMMING TROUBLESHOOT-
ING
GUID-0B904713-E37A-46A3-9A90-63FADE14E79CIf the HomeLink®does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter batteries
with new batteries.
. position the hand-held transmitter with its
battery area facing away from the
HomeLink
®surface.
. press and hold both the HomeLink®and
hand-held transmitter buttons without inter-
ruption.
. position the hand-held transmitter 1-3 in
(26-76 mm) away from the HomeLink
®
surface. Hold the transmitter in that position
for up to 15 seconds. If HomeLink®is not
programmed within that time, try holding the
transmitter in another position - keeping the
indicator light in view at all times.
If you have any questions or are having difficulty
programming your HomeLink
®buttons, refer to
the HomeLink®web site at: www.homelink.com
or 1-800-355-3515.
CLEARING THE PROGRAMMED IN-
FORMATION
GUID-8C1871E3-C252-465F-A399-47B1EB58E018The following procedure clears the programmed
information from both buttons. Individual buttons
cannot be cleared. However, individual buttons
can be reprogrammed, see “Reprogramming a
single HomeLink
®button” later in this section.
To clear all programmingGUID-A8FB6BA7-7DB6-4CE5-B9B3-E2187D21C0EE1. Press and hold the two outer HomeLink®
buttons until the indicator light begins to
flash in approximately 10 seconds. Do not
hold for longer than 20 seconds.
2. Release both buttons.
HomeLink
®is now in the programming mode
and can be programmed at any time beginning
with “Programming HomeLink
®” - Step 1.
REPROGRAMMING A SINGLE
HomeLink®BUTTONGUID-2BF52974-A0FA-4080-821F-2E188B5DC58BTo reprogram a HomeLink®Universal Transcei-
ver button, complete the following.
1. Press and hold the desired HomeLink
®
button. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink
®
button, proceed with “Programming
HomeLink®” - Step 1.
For questions or comments, contact HomeLink®
Condition:
Page 155 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (153,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3 Pre-driving checks and adjustments
Keys...
........................................................................\
...................... 3-3](/img/5/332/w960_332-154.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (153,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3 Pre-driving checks and adjustments
Keys...
........................................................................\
...................... 3-3")
Black plate (153,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3 Pre-driving checks and adjustments
Keys...
........................................................................\
...................... 3-3
Intelligent Key system ...
......................................................... 3-3
Mechanical key ...
.................................................................... 3-4
Valet hand-off ...
....................................................................... 3-5
Doors ...
........................................................................\
.................... 3-5
Locking with mechanical key ...
............................................ 3-5
Opening and closing windows with the
mechanical key ...
..................................................................... 3-6
Locking with inside lock knob ...
.......................................... 3-6
Locking with power door lock switch ...
............................ 3-7
Automatic door locks ...
......................................................... 3-7
Child safety rear door lock (Hardtop models) ...
............. 3-8
Intelligent Key system ...
.............................................................. 3-8
Intelligent Key operating range ...
..................................... 3-10
Door locks/unlocks precaution ...
..................................... 3-10
Intelligent Key operation ...
................................................. 3-11
Battery saver system ...
....................................................... 3-14
Warning signals ...
................................................................ 3-14
Troubleshooting guide ...
..................................................... 3-15
Remote keyless entry system ...
............................................. 3-16
How to use remote keyless entry system ...
.................. 3-17
Hood ...
........................................................................\
.................. 3-20
Lift gate (Hardtop models) ...
.................................................. 3-20
Operating manual lift gate ...
............................................. 3-21
Operating power lift gate (if so equipped) ...
............... 3-21 Auto closure
...
.................................................................... 3-24
Lift gate release ...
.............................................................. 3-25
Trunk lid (CrossCabriolet models) ...
.................................... 3-25
Trunk lid release switch ...
................................................ 3-25
Trunk open request switch ...
.......................................... 3-26
Trunk button ...
.................................................................... 3-26
Opening with key ...
........................................................... 3-26
Trunk release power cancel switch ...
........................... 3-26
Interior trunk lid release ...
................................................ 3-27
Soft top (CrossCabriolet models) ...
.................................... 3-28
Before operating the top ...
.............................................. 3-28
When operating the top ...
............................................... 3-32
Luggage cover ...
................................................................ 3-33
Soft top indicator light ...
.................................................. 3-33
Automatic window lowering ...
........................................ 3-34
Opening the top ...
............................................................. 3-34
Closing the top ...
............................................................... 3-35
Opening the top using the intelligent key ...
............... 3-35
Troubleshooting guide ...
.................................................. 3-37
If the top does not open or close electrically ...
......... 3-38
Care of the soft top and the vehicle body ...
.............. 3-43
Fuel-filler door ...
........................................................................\
3-44
Opening fuel-filler door ...
................................................ 3-44
Fuel-filler cap ...
.................................................................. 3-44
Condition:
Page 162 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (160,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-8Pre-driving checks and adjustments
SPA2433
CHILD SAFETY REAR DOOR LOCK
(Hardtop models)
GUID-02E4EA0C-4602-4E41-993C-FC56ED415767The child saf](/img/5/332/w960_332-161.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (160,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-8Pre-driving checks and adjustments
SPA2433
CHILD SAFETY REAR DOOR LOCK
(Hardtop models)
GUID-02E4EA0C-4602-4E41-993C-FC56ED415767The child saf")
Black plate (160,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-8Pre-driving checks and adjustments
SPA2433
CHILD SAFETY REAR DOOR LOCK
(Hardtop models)
GUID-02E4EA0C-4602-4E41-993C-FC56ED415767The child safety rear door locks help prevent
doors from being opened accidentally, espe-
cially when small children are in the vehicle.
When the levers are in the lock position
*1, the rear doors can be opened only
from the outside.
To disengage, move the levers to the unlock
position
*2.
GUID-A26B93CD-32CF-44F2-8707-5F0887B9E015
WARNING
. Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should con-
tact the electric medical equipment
manufacturer for the possible influ-
ences before use.
. The Intelligent Key transmits radio
waves when the buttons are
pushed. The FAA advises that radio
waves may affect aircraft navigation
and communication systems. Do not
operate the Intelligent Key while on
an airplane. Make sure the buttons
are not operated unintentionally
when the unit is stored for a flight.
The Intelligent Key system can operate all the
door (including the lift gate) and the trunk lid
locks using the remote keyless function or
pushing the request switch on the vehicle
without taking the key out from a pocket or
purse. The operating environment and/or condi-
tions may affect the Intelligent Key system
operation.
Be sure to read the following before using the
Intelligent Key system.
CAUTION
. Be sure to carry the Intelligent Key
with you when operating the vehi-
cle.
. Never leave the Intelligent Key in
the vehicle when you leave the
vehicle.
The Intelligent Key is always communicating with
the vehicle as it receives radio waves. The
Intelligent Key system transmits weak radio
waves. Environmental conditions may interfere
with the operation of the Intelligent Key system
under the following operating conditions.
. When operating near a location where
strong radio waves are transmitted, such
as a TV tower, power station and broad-
casting station.
. When in possession of wireless equipment,
such as a cellular telephone, transceiver,
and CB radio.
. When the Intelligent Key is in contact with or
covered by metallic materials.
. When any type of radio wave remote control
is used nearby.
. When the Intelligent Key is placed near an
electric appliance such as a personal
INTELLIGENT KEY SYSTEM
Condition:
Page 170 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (168,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-16Pre-driving checks and adjustments
GUID-2CA37571-0169-4EEF-8C1B-5C2849855720
WARNING
The Intelligent Key transmits radio
waves when the butto](/img/5/332/w960_332-169.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (168,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-16Pre-driving checks and adjustments
GUID-2CA37571-0169-4EEF-8C1B-5C2849855720
WARNING
The Intelligent Key transmits radio
waves when the butto")
Black plate (168,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-16Pre-driving checks and adjustments
GUID-2CA37571-0169-4EEF-8C1B-5C2849855720
WARNING
The Intelligent Key transmits radio
waves when the buttons are pushed.
The FAA advises that radio waves may
affect aircraft navigation and commu-
nication systems. Do not operate the
Intelligent Key while on an airplane.
Make sure the buttons are not operated
unintentionally when the unit is stored
for a flight.
It is possible to lock/unlock all doors and the lift
gate/trunk lid, activate the panic alarm and open
the windows and lift gate/trunk lid (if so
equipped) by pushing the buttons on the
Intelligent Key from outside the vehicle.
Before locking the doors, make sure the
Intelligent Key is not left in the vehicle.
The LOCK/UNLOCK button on the Intelligent
Key can operate at a distance of approximately
33 ft (10 m) from the vehicle. (The effective
distance depends upon the conditions around
the vehicle.) As many as 4 Intelligent Keys can
be used with one vehicle. For information
concerning the purchase and use of additional
Intelligent Keys, contact a NISSAN dealer.
The lock and unlock buttons will not operate when:
.
the distance between the Intelligent Key and
the vehicle is over 33 ft (10 m) .
. the Intelligent Key battery is discharged.
After locking with the remote keyless entry
function, pull the door handle to make sure the
doors are securely locked.
The LOCK/UNLOCK operating range varies
depending on the environment. To securely
operate the lock and unlock buttons, approach
the vehicle to about 3 ft (1 m) from the door.
SPA2252A
Type A
SPA2436
Type B
REMOTE KEYLESS ENTRY SYSTEM
Condition:
Page 172 of 507
![NISSAN MURANO 2013 2.G Repair Manual Black plate (170,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-18Pre-driving checks and adjustments
button*2again until the window opens
completely.
The door windows can be opened or closed by
turning the m](/img/5/332/w960_332-171.png "NISSAN MURANO 2013 2.G Repair Manual Black plate (170,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-18Pre-driving checks and adjustments
button*2again until the window opens
completely.
The door windows can be opened or closed by
turning the m")
Black plate (170,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-18Pre-driving checks and adjustments
button*2again until the window opens
completely.
The door windows can be opened or closed by
turning the mechanical key in a door lock. (See
“Doors” earlier in this section.)
Opening/closing lift gate (if so equipped)GUID-7A0EC3F3-A0FF-43A5-983C-6F30EE025AB41. Push the power lift gatebutton*3
for more than 1 second.
2. The lift gate will automatically open.
The hazard indicator flashes 4 times and the
outside chime sounds for approximately 3
seconds.
To close the lift gate, push the power lift gate
button*3.
The lift gate will automatically close.
If the power lift gate
button*3is pushed
while the lift gate is being opened or closed, the
lift gate will reverse.
The power lift gate
button*3cannot be
operated when the ignition switch is in the ON
position.
Using panic alarmGUID-0EEA2C46-8F73-4264-8914-B8CE095E8B5CIf you are near your vehicle and feel threatened,
you can activate the alarm according to the
following procedure to call attention.
1. Push the PANIC
button*4for more
than 1 second.
2. The theft warning alarm will sound and the headlights will flash for 25 seconds.
3. The panic alarm stops under either of the following conditions.
.It has run for 25 seconds, or.Any of the buttons is pushed. (Note: thePANIC
button*4should be
pushed for more than 1 second.)
Opening trunk lid (CrossCabriolet mod-
els)
GUID-87B7F82C-E682-4BF3-BE6B-52CC949856EB1. Push the TRUNKbutton*5on the
Intelligent Key for more than 1 second.
2. The trunk will unlatch.
3. Raise the trunk lid to open the trunk.
Setting hazard indicator and horn modeGUID-0B7C4602-8422-4E4E-A11F-E789553B0A3DThis vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
In hazard indicator and horn mode, when the
LOCK
button*1is pushed, the hazard
indicator flashes twice and the horn chirps once.
When the UNLOCK
button*2is pushed,
the hazard indicator flashes once.
If horns are not necessary, the system can be
switched to the hazard indicator mode.
In hazard indicator mode, when the LOCK
button*1is pushed, the hazard indicator
flashes twice. When the UNLOCK
button
*2is pushed, neither the hazard indicator nor
the horn operates.
Condition: