immobilizer NISSAN NOTE 2016 Service Workshop Manual

B2198 NATS ANTENNA AMP.SEC-61
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.
Is the inspection result normal?
YES >> Replace NATS antenna amp. Refer to SEC-114, "Removal and Installation".
NO >> GO TO 8.
8.CHECK NATS ANTENNA AMP. OUTPUT SIGNAL CIRCUIT 2
1. Disconnect BCM connector.
2. Check continuity between NATS antenna amp. harness connector and BCM connector.
3. Check continuity between NATS antenna amp. harness connector and ground.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace harness.
9.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End
(+) (–) Condition Voltage (V)
(Approx.)
NATS antenna amp.
Connector Terminal
M21 3 Ground Intelligent Key: Intelligent
Key battery is removed.Brake pedal: Depressed
NOTE:
Waveform varies each time
when brake pedal is de-
pressed.
Brake pedal: Not depressed
Battery voltage
JMKIA6233JP
NATS antenna amp. BCM
Continuity
Connector TerminalConnector Terminal
M21 3M97 25Yes
NATS antenna amp. GroundContinuity
Connector Terminal
M21 3 No
Revision: August 2015 2016 Versa Note

cardiagn.com

B2555 STOP LAMPSEC-63
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
3.CHECK STOP LAMP SWITCH INPUT SIGNAL 2
1. Connect stop lamp switch connector.
2. Check voltage between BCM harness connector and ground.
Is the inspecting result normal?
YES >> GO TO 4.
NO >> GO TO 5.
4.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
5.CHECK STOP LAMP SWITCH CIRCUIT
1. Disconnect stop lamp switch connector.
2. Check continuity between stop lamp switch harness connector and BCM harness connector.
3. Check continuity between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK STOP LAMP SWITCH
Refer to SEC-63, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace stop lamp switch. Refer to BR-20, "
Exploded View".
7.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430375
1.CHECK STOP LAMP SWITCH
1. Turn ignition switch OFF.
(+)
(–)Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M97 9Ground Brake pedal Depressed Battery voltage
Not depressed 0
St op la mp sw i tc h BC M
Continuity
Connector TerminalConnector Terminal
E13 (CVT) 2M979 Y es
E57 (MT)
St op la mp sw i tc h GroundContinuity
Connector Terminal
E13 (CVT) 2N o
E57 (MT)
Revision: August 2015 2016 Versa Note

cardiagn.com

SEC-66
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2556 PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
4.CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK PUSH-BUTTON IGNITION SWITCH
Refer to SEC-66, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace push-button ignition switch. Refer to SEC-115, "
Removal and Installation".
6.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
Component InspectionINFOID:0000000012430378
1.CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check continuity between push- button ignition switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace push-button ignition switch. Refer to SEC-115, "
Removal and Installation".
Push-button ignition switch
GroundContinuity
Connector Terminal
M25 4 Yes
Push-button ignition switch
Condition Continuity
Te r m i n a l
48 Push-button ignition
switchPressed
Yes
Not pressed No
Revision: August 2015 2016 Versa Note

cardiagn.com

B2601 SHIFT POSITIONSEC-69
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
2.CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R connector.
2. Check continuity between CVT shift selector (par k position switch) harness connector and IPDM E/R har-
ness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B2601. Refer to SEC-68, "
DTC Logic".
Is DTC B2601 detected again?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO >> Inspection End.
CVT shift selector (park position switch) IPDM E/R
Continuity
Connector TerminalConnector Terminal
M38 8E47 80Yes
Revision: August 2015 2016 Versa Note

cardiagn.com

B2602 SHIFT POSITIONSEC-71
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.REPLACE BCM
1. Replace BCM. Refer to PCS-30, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
6.CHECK CVT SHIFT SELECTOR CIRCUIT
1. Disconnect BCM connector and IPDM E/R connector.
2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness connector.
3. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)
Refer to SEC-72, "
Component Inspection".
Is the inspection result normal?
(+)
(–)Voltage (V)
(Approx.)
CVT shift selector (park position switch)
Connector Terminal
M38 7GroundBattery voltage
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 7M98 104Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 7 No
CVT shift selector (park position switch) BCM
Continuity
Connector TerminalConnector Terminal
M38 8M97 37Yes
CVT shift selector (park position switch) GroundContinuity
Connector Terminal
M38 8 No
Revision: August 2015 2016 Versa Note

cardiagn.com

SEC-76
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B2603 SHIFT POSITION
YES >> GO TO 11.
NO >> Repair or replace harness.
11 .CHECK CVT SHIFT SELECTOR
(PARK POSITION SWITCH)
Refer to SEC-76, "
Component Inspection [CVT Shift Selector (Park Position Switch)]".
Is the inspection result normal?
YES >> GO TO 13.
NO >> Replace CVT shift selector. Refer to TM-231, "
Removal and Installation".
12.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
13.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
Component Inspection (T ransmission Range Switch)INFOID:0000000012430388
1.CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace transmission range switch.
Component Inspection [CVT Shift Selector (Park Position Switch)]INFOID:0000000012430389
1.CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Check continuity between CVT shift se lector (park position switch) terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace CVT shift selector. Refer to TM-231, "
Removal and Installation".
Transmission range switch
Condition Continuity
Te r m i n a l
71 0P or N position
Yes
Other than above No
CVT shift selector (detention switch)
Condition Continuity
Terminal
78 Selector lever: P positionSelector button: Released No
Selector button: Pressed
Ye s
Selector lever: Other than P position
Revision: August 2015 2016 Versa Note

cardiagn.com

B2604 SHIFT POSITIONSEC-79
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK TRANSMISSION RANGE SWITCH
Refer to SEC-79, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Replace transmission range switch.
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> Inspection End.
9.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
Component InspectionINFOID:0000000012430392
1.CHECK TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Check continuity between trans mission range switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace transmission range switch.
Transmission range switch ConditionContinuity
Te r m i n a l
71 0P or N position
Yes
Other than above No
Revision: August 2015 2016 Versa Note

cardiagn.com

B2605 SHIFT POSITIONSEC-81
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec- tor.
5. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
3.CHECK BCM INPUT SIGNAL
1. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK BCM INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Disconnect transmission range switch connector.
4. Check continuity between BCM harness connecto r and transmission range switch harness connector.
5. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM using CONSULT. Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to SEC-80, "
DTC Logic".
Is DTC B2605 detected again?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO >> Inspection End.
IPDM E/R Transmission range switch
Continuity
Connector TerminalConnector Terminal
F 424 0F 521 0Y es
IPDM E/R GroundContinuity
Connector Terminal
F42 40 No
(+)
(–)Condition Voltage (V)
(Approx.)
BCM
Connector Terminal
M98 102Ground Selector lever P or N position Battery voltage
Other than above 0
BCM Transmission range switch
Continuity
Connector TerminalConnector Terminal
M98 102F52 10Yes
BCM GroundContinuity
Connector Terminal
M98 102 No
Revision: August 2015 2016 Versa Note

cardiagn.com

B2608 STARTER RELAYSEC-83
< DTC/CIRCUIT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
SEC
N
O P
3.CHECK STARTER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect starter relay.
3. Disconnect BCM connector.
4. Check continuity between starter relay harness connector and BCM harness connector.
5. Check continuity between starter relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
4.CHECK STARTER RELAY
Refer to SEC-83, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace starter relay.
5.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of al l Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
3. Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to SEC-80, "
DTC Logic".
Is DTC B2605 detected again?
YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO >> Inspection End.
Component InspectionINFOID:0000000012430397
1.CHECK STARTER RELAY
1. Turn ignition switch OFF.
2. Disconnect starter relay.
3. Check continuity between starter relay terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace starter relay.
Starter relay BCM
Continuity
Connector TerminalConnector Terminal
E41 1M98 97Yes
Starter relay GroundContinuity
Connector Terminal
E41 1 No
Starter relay
ConditionContinuity
Te r m i n a l
35 12 V direct current supply between terminals 1 and 2
Yes
No current supply No
Revision: August 2015 2016 Versa Note

cardiagn.com

SEC-86
< DTC/CIRCUIT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
B261F ASCD CLUTCH SWITCH
3.CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY
1. Disconnect clutch interlock switch connector.
2. Turn ignition switch ON.
3. Check voltage between clutch interlock switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK CLUTCH INTERLOCK SWITCH SIGNAL
1. Connect clutch interlock switch connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 6.
5.REPLACE BCM
1. Replace BCM. Refer to BCS-74, "
Removal and Installation".
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
6.CHECK CLUTCH INTERLOCK SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between clutch interlock switch harness connector and BCM harness connector.
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace harness.
7.CHECK CLUTCH INTERLOCK SWITCH
Refer to SEC-87, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Replace clutch interlock switch. Refer to CL-11, "
Exploded View".
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
(+)
(–)Voltage (V)
(Approx.)
Clutch interlock switch
Connector Terminal
E34 1GroundBattery voltage
(+)
(–)Condition Voltage
BCM
Connector Terminal
M98 101Ground Clutch pedal Released
0 V
Depressed Battery voltage
Clutch interlock switch BCM
Continuity
Connector TerminalConnector Terminal
E34 2M98 101Yes
Revision: August 2015 2016 Versa Note

cardiagn.com