tow NISSAN PATHFINDER 2007 R51 / 3.G Quick Reference Guide

headlight and turn signal control
HEADLIGHT SWITCH
 Turn the headlight switch to the position to
turn on the front parking, tail, license plate and
instrument panel lights.
 Turn the headlight switch to the position to
turn on the headlights. All other lights remain on.
HIGH BEAM
 Push the headlight switch forward to select the high beam function. The blue

indicator light illuminates. Pull the headlight switch back to the original position to

select the low beam. The blue
indicator light goes off.
 Pull and release the headlight switch to flash the headlight high beams on and off.
TURN SIGNAL SWITCH
 Move the headlight control switch up or down to signal the turning direction. When
the turn is completed, the turn signals cancel automatically.
 To signal a lane change, move the headlight control switch up or down to the point
where the indicator light begins to flash, but the headlight control switch does not
latch.
AUTOMATIC HEADLIGHT OPERATION (if so equipped)
The autolight system can:
 Turn the headlights on automatically when it is dark.
 Turn the headlights off automatically when it is light.
 Keep the headlights on for 45 seconds after you turn the ignition switch to OFF and
all doors are closed.
WINDSHIELD WIPER/WASHER SWITCH
 The ignition switch must be in the ON position
to activate the windshield wipers.
 Move the lever to the following positions to
operate the windshield wipers:
1a Intermittent (INT) – Front wipers operate
intermittently and can be further adjusted
by twisting the time control ring 1B.
02 Low Speed (LO) – Continuous low-speed
operation of front wipers.
03 High Speed (HI) – Continuous high-speed
operation of front wipers.
04 Mist (MIST) – Lift the lever up for one sweep of the front wipers.
05 Rear Wipers (REAR) – Twist the end section to operate the first (INT)
or second (ON) speed settings for the rear wipers.
 The washer function activates the washer fluid and several sweeps of the wipers:
• For F
RONT WASHER, pull lever toward you.
• For REAR WASHER, push lever away from you.

1a
02
03
04
1B05

 Push the switch 02 forward to move the seatback forward; push it back to move the seatback backward.
LUMBAR SUPPORT (if so equipped) Your driver’s seat has a lumbar support; adjust it by moving the lever
03 up or down.
03
folding the 3rd row seats
 Pull up on the latches 01 located in the outer corners of each seatback and fold the seatbacks forward over the seat base.
 To return the 3rd row seats to a seating position use the pull straps 02 to raise each seatback. Pull back until the seatback latches into position.
Make sure to properly raise each seatback to an upright and
secured position.
folding the 2nd row Bench seat
To fold the 2nd row bench seat flat for maximum cargo hauling:
 Lower the head restraint to the “down” position.
 Pull the strap 01 located in the center of the seat cushion toward the front of the vehicle.  Lift up on the recline lever 02 to fold the seatback forward.
 Fold the carpet panel flap 03 toward the back of the vehicle. (The carpet panel flap provides a level cargo floor when the 3rd row seats are also folded flat.)
 Reverse this process to return the 2nd row bench seats to a seating position.
Make sure to properly raise the seatback to an upright position and push the seat cushion down into place.
01
02
03
01
02
ti P uP for eas Y entr Y or exit fro M the 3rd
row
The 2nd row outboard seats can be tipped forward for easy entry or exit from the 3rd row bench seat.
 To enter the 3rd row, lift up on the latch located on the upper corner of the seatback 01 on the back of the 2nd row outboard seats.
 This will then release the back of the seat and tip the 2nd row outboard seat forward. 02
 To exit the 3rd row bench seat, lift up on the same latch and tip the seatback forward.
01
02

This easy-to-use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle. However, it is not intended to replace your Owner’s Manual. The Owner’s Manual contains more detailed information to help you better understand the important safety warnings, features, operation, and maintenance of your vehicle.
QR7E-0R51U1 Printing: January 2007 (09)
Nissan, the Nissan Brand Symbol, “SHIFT_” tagline, Z and Nissan model names are Nissan trademarks. ©2007 Nissan North America, Inc.
Sh ift_
sunroof controls (if so equipped)
The ignition switch must be in the ON position to operate the sunroof.
TILTING THE SUNROOF
 To tilt the sunroof up, first close the sunroof by pushing the switch toward UP/CLOSE 01. Release the switch, then push the UP/CLOSE switch again to tilt the sunroof up.
 To tilt the sunroof down, push the switch toward DOWN/OPEN 02.
SLIDING THE SUNROOF
 To fully open the sunroof, push the switch toward DOWN/OPEN. To open the sunroof part way, push the switch in any direction while the sunroof is sliding to stop it in the desired position.
 To fully close the sunroof, push the switch toward UP/CLOSE. To close the sunroof part way, push the switch in any direction while the sunroof is sliding to stop it in the desired position.
02
01
fuel-filler door
The fuel-filler door lock (if so equipped) is automatically engaged with the door lock system.
1. Unlock the fuel-filler door using one of the following
operations.
 Press the
lpd0151
button on the keyfob once to unlock
the driver’s door and the fuel-filler door.
 Unlock all doors with the key cylinder. (Turn twice.)
 Press
lpd0151
on the power door lock switch.
 NOTE: The fuel-filler door will remain locked if the driver’s door is manually
unlocked using the inside door lock handle lever.
2. Push the left side of the fuel-filler door to open.
3. To lock, close the fuel-filler door and lock all doors.