glove box NISSAN PICK-UP 1999 Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1999, Model line: PICK-UP, Model: NISSAN PICK-UP 1999Pages: 666, PDF Size: 16.21 MB
Page 37 of 666
CAUTION:
lDisconnect both terminals from battery in advance.
lDisconnect air bag module connector in advance.
lBe careful not to scratch finishers and other parts.
lNever tamper with or force air bag lid open, as this may adversely affect air bag performance.
REMOVAL Ð Instrument panel assembly
Instrument panel assemblyCombination meterAudio controlHeater and A/C control
Remove driver's air bag module and steering wheel.
Refer to ªSUPPLEMENTAL RESTRAINT SYSTEMº in RS
section for details.Tilt steering column down
fully
V1Steering column coverlRemove screws.
V2Instrument lower panel driver side.lRemove screws and bolts.
V3Cluster lid AlRemove screws.
V4Combination meterlRemove screws, then disconnect harness connectors.
V5Glove box assemblylRemove screws.lThen disconnect passenger air bag module connec-
tor.
lThen remove passenger air bag module bracket.
Refer to ªSUPPLEMENTAL RESTRAINT SYSTEMº
in RS section for details.
V6Remove ashtray.
V7Cluster lid ClRemove screws, then disconnect harness connectors.
V8Audio and deck pocketlRemove screws, then disconnect harness connectors.
V9Heater and A/C controllDisconnect temperature control cable and harness connectors.
V10Instrument stay cover lower centerlRemove screws.
V11Ventilator grille driver side
V12Defroster grille
Remove front pillar garnish.
Refer to ªSide and Floor Trimº in ªINTERIOR TRIMº for
details, BT-2007.
V13Instrument panel assemblylRemove screws and bolts.
V14Air duct passenger sidelRemove screws.
V15Passenger air bag modulelRefer to ªSUPPLEMENTAL RESTRAINT SYSTEMº
in RS section for details.
INSTRUMENT PANEL
BT-2004
Page 633 of 666
Removal Ð Front Passenger Air Bag Module
CAUTION:
lBefore servicing SRS, turn the ignition switch off, dis-
connect both battery cables and wait for at least 3 min-
utes.
lAlways work from the side of or under air bag module.
1. Remove glove box assembly. Refer to ``INSTRUMENT
PANEL'' in BT section for details.
2. Disconnect passenger air bag module connector.
3. Remove bolts and special bolts using the TAMPER RESIS-
TANT TORX (Size T50) from front passenger air bag mod-
ule.
4. Remove instrument panel assembly. Refer to ``INSTRU-
MENT PANEL'' in BT section for details.
5. Remove air duct from instrument panel.
6. Remove the bolts from left and right sides of front passen-
ger air bag module. Then remove the air bag module from
the instrument panel assembly.
lThe air bag module is heavy and should be supported using
both hands during removal.
CAUTION:
lAlways place air bag module with pad side facing
upward.
lDo not attempt to disassemble air bag module.
lThe special bolts are coated with bonding agent. Do not
use old bolts after removal; replace with new coated
bolts.
lDo not insert any foreign objects (screwdriver, etc.) into
air bag module connector.
lReplace air bag module if it has been dropped or sus-
tained an impact.
lDo not expose the air bag module to temperatures
exceeding 90ÉC (194ÉF).
lDo not allow oil, grease or water to come in contact with
the air bag module.
Installation Ð Front Passenger Air Bag
Module
lAlways work from the side of or under air bag module.
1. Install front passenger air bag module to instrument panel
assembly.
2. Install air duct to instrument panel.
3. Install instrument panel.
lEnsure harness is not caught between rear of air bag mod-
ule and steering member.
4. Install front passenger air bag module to steering member.
5. Connect air bag module connector.
6. Install glove box assembly.
SRS730
SRS570
SBF814E
SRS731
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
RS-2011