lights NISSAN QUEST 2014 RE52 / 4.G Quick Reference Guide

5
TIre Pre SSure MONITOr ING SYSTeM (TPMS)
wITH eaSY FILL TI re aLerT

A CHe CK TIre P reSSure warning message will
appear in the vehicle information display
01 and

the low tire pressure warning light 02 will

illuminate when one or more tires are low on
pressure and air is needed.
•
The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mi (1.6 km) at moderate speeds.


When adding air to an under-inflated tire, the TPMS with
Easy Fill Tire Alert provides visual and audible signals
outside the vehicle to help you inflate the tires to the
recommended c OLD tire pressure.

To use the Easy Fill Tire Alert system:
1. Move the shift lever to the P (P arK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3.
Add air to the under-inflated tire, and within a few seconds the hazar\
d warning lights will
start flashing.
4.
When the designated tire pressure is reached, the horn will beep once and the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.


After tire pressures are adjusted, drive the vehicle at speeds above 16 MPH (25 km/h).
The CHe CK TIre PreSS ure warning message and low tire pressure warning light
will disappear.


When the low tire pressure warning light flashes for 1 minute and then \
remains on, the TPMS
is not functioning properly. Have the system checked by a NISSAN dealer.


Tire pressure rises and falls depending on the heat caused by the vehicle\
’s operation and the
outside temperature. Low outside temperature can lower the temperature o\
f the air inside
the tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure
warning light to illuminate. If the warning light illuminates, check the tire pressure in your tires.
• check the tire pressure (including the spare tire) often and always prior \
to long distance trips.

The Tire and Loading Information label contains valuable information. Please refer to section 9,
“Technical and consumer information”, in your Owner’s Manual for the location of the Tire and
Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
01
02
To view detailed instructional videos regarding these and other features, please go\
to www.nissanownersinfo.mobi
esse Ntial i Nfor matio N
1490690_14_Quest_QRG_072513.indd 57/25/13 9:23 AM

7
01
03
04
05
06
02
NISSaN INTeLLIGeNT K eY® SYST eM
The NISSAN Intelligent k ey® System allows you to lock or
unlock your vehicle, open your liftgate and start the engine.
It is important to make sure the Intelligent k ey is with you
(that is, in your pocket or purse).

The operating range of the Intelligent k ey is within
31.5 in (80 cm) from each request switch.


To lock the vehicle, push either door handle request
switch
01 or the liftgate request switch 02 or press

the
button 03 on the key fob.


To unlock the vehicle, perform one of the
following procedures:
•
Push either door handle request switch
01 or the

liftgate request switch 02; the corresponding door
will unlock. Push the request switch again within 1
minute; all other doors will unlock, or
•
Press the

button 04 on the key fob to unlock the

driver’s side door. Press the button 04 again

within 1 minute; all other doors will unlock.


To open the power liftgate (if so equipped), press the
button 05 for more than 1 second.


The Intelligent k ey can also be used to activate the
panic alarm by pressing and holding the
button 06

for more than 1 second. Once activated, the panic
alarm and headlights will stay on for a period of time.
INTELLIGENT k EY BATTERY DIS cHARGE


If the battery of the Intelligent k ey is discharged, or
environmental conditions interfere with the Intelligent
k ey operation, start the engine according to the
following procedure:
1. Move the shift lever to the P (ParK) position.
2. Firmly apply the foot brake.
3.
Touch the ignition switch with the Intelligent k ey and
a chime will sound.
4.
Within 10 seconds after the chime sounds, push the
ignition switch while depressing the brake pedal and
the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)”
and the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
f irst drive features
To view detailed instructional videos regarding these and other features, please go\
to www.nissanownersinfo.mobi
1490690_14_Quest_QRG_072513.indd 77/25/13 9:23 AM

13
HeaDLIGHT CONTr OL SwITCH
HEADLIGHT cONTROL

Turn the headlight control switch to the
position
01 to turn on the front parking, side marker, tail, license

plate and instrument panel lights. Turn the switch to the
position
02 to turn on the headlights.
AUTOLIGHT SYSTEM (if so equipped)

The autolight system will automatically turn the headlights on when it is\
dark and off when it is
light. The system will keep the headlights on for a period of time after you tur\
n the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to the au TO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF position,
position 01 or
position
02.
HIGH BEAM SELE cT

Push the headlight control switch forward
04 to

select the high beam function. The blue indicator light
illuminates in the instrument panel. Pull the
headlight switch back to the original position to select
the low beam
. The blue indicator light goes off.

Pull and release the headlight control switch
05 to

flash the headlight high beams on and off.
FOG LIGHT SWIT cH (if so equipped)

The headlights must be on and the low beams

selected for the fog lights to operate.

Turn the switch (inside collar) to the position
06 to

turn the fog lights on.

Turn the switch (inside collar)
to the OFF position to

turn the fog lights off.
LANE c HANGE SIGNAL

To signal a lane change, move the lever up or down to the point where the indicator light
begins to flash, but the lever does not latch.

The turn signal will flash 3 times automatically.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
01
04
03
02
05
06
To view detailed instructional videos regarding these and other features, please go\
to www.nissanownersinfo.mobi
1490690_14_Quest_QRG_072513.indd 137/25/13 9:24 AM

27
HOMeLINK® uNIVer SaL TraNSCe IVer (if so equipped)
The HomeLink system can learn and consolidate the functions of up to 3 di\
fferent
hand-held transmitters, operating items such as garage doors, property gates, outdoor and
indoor lights or alarm systems.

To program the Homelink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink surface,
keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter \
button
simultaneously until the HomeLink indicator light flashes slowly and then ra\
pidly.
• Both buttons may be released when the indicator light flashes rapidly.

To verify the programing is complete, press and hold the HomeLink button \
and observe the
indicator light:
• A solid continuous light indicates the programing is complete and the Ho\
meLink button
will activate your device.
• A blinking light that turns to a solid continuous light after 2 seconds \
indicates additional
steps are required to complete the programing.

An additional person may make the remaining steps easier. To complete the
programing process:
• At the receiver of the device that you are programing to the HomeLink bu\
tton, press
and release the learn or smart button (the name may vary by manufacture\
r, but it is
usually located near where the hanging antenna wire is attached to the unit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.

Repeat the previous 2 steps up to 3 times to complete the programing pro\
cess. HomeLink
should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
HOMeLINK®
To view detailed instructional videos regarding these and other features, please go\
to www.nissanownersinfo.mobi
1490690_14_Quest_QRG_072513.indd 277/25/13 9:24 AM