windshield wipers NISSAN SENTRA 2017 B17 / 7.G Quick Reference Guide

14
To activate the autolight system, turn the headlight control switch to the AUTO
position 3 then place the ignition switch in the ON position. To deactivate the
autolight system, turn the headlight control switch to the OFF position,
position 1 or position 2.
HIGH BEAM SELECT

With the headlights ON (either in the AUTO
position 3 or position 2), push the
headlight control switch forward 4 to select
the high beam function. The blue indicator
light
will illuminate in the instrument panel.
Pull the headlight switch back to the original
position to select the low beam. The blue indicator light will extinguish.

Pull and release the headlight control switch 5 to flash the headlight high
beams on and off.
FOG LIGHT SWITCH (if so equipped)

The headlights must be in the AUTO position 3 or the low beams selected for the fog
lights to operate.

Turn the switch (inside collar) to the
position 6 to turn the fog lights on.

Turn the switch (inside collar) to the OFF position to turn the fog lights off.
LANE CHANGE SIGNAL

Move the lever up or down until the turn signal begins to flash but the lever
does not latch to signal a lane change. Hold the lever until the lane change
is completed.

Move the lever up or down until the turn signal begins to flash but the lever does
not latch and release the lever. The turn signal will automatically flash three times.
Choose the appropriate method to signal a lane change based on road and
traffic conditions.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
6
45
WIPER AND WASHER SWITCH
Move the lever to one of the following
positions to operate the windshield wipers:

1 Mist (MIST) – One sweep operation of
the wipers.

2 Intermittent (INT) – Wipers operate
intermittently. The intermittent operation
speed can be adjusted by twisting the
time control ring
3 to increase or
decrease wiper speed.

4 Low ( LO) – Wipers operate at a continuous low-speed.
1
2
4
5
MIST
OFFINT
LO
HI3
FIRST DRIVE FEATURES
2434454_17b_Sentra_US_pQRG_101416.indd 1410/14/16 10:59 AM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.

15
6
5 High (HI) – Wipers operate at
a continuous high-speed.

6 Pull the lever toward you to activate
the washer. The wipers will operate
several times.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service
position in order to replace the wiper blades.
To move the wiper blades to the service position,
follow this procedure:

When the ignition switch is in the ON position
or within 60 seconds of placing the ignition
switch in the OFF position, lif t the windshield
wiper and washer lever up to the MIST position
1 two times in less than 0.5
seconds. The windshield wipers will move to the service position automatically,
and the wiper blades can now be replaced.
To move the wiper blades back to the original position:

Lif t the windshield wiper and washer lever up for more than 1 second or lower
the lever down to operate at any wiper speed.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Do-it-yourself
(section 8)” of your Owner’s Manual.
12
3
5
4
6
78
9
10
1112
HEATER AND AIR CONDITIONER (automatic) (if so equipped)
1 AUTO BUTTON

This mode may be used year-round. Press the AUTO button to turn the
system on. The system will automatically control the inside temperature
(automatic cooling and/or dehumidified heating), air flow distribution and fan
speed. The A/C automatically turns on when the AUTO button is selected.
2434454_17b_Sentra_US_pQRG_101416.indd 1510/14/16 10:59 AM
To view detailed instructional videos regarding these and other features, please go to www.nissanownersinfo.mobi.