transmission NISSAN TEANA 2003 Service Manual

CVT INDICATOR CIRCUIT
CVT-159
D
E
F
G
H
I
J
K
L
MA
B
CVT

CVT INDICATOR CIRCUITPFP:24810
DescriptionBCS001M6
TCM sends the switch signals to unified meter and A/C amp via CAN communication line. Then manual mode
switch position is indicated on the CVT indicator.
CONSULT-II Reference ValueBCS001M7
Diagnostic ProcedureBCS001M8
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-II and read
out the value of “M GEAR POS”.
3. Drive vehicle in the manual mode, and confirm that the actual gear position and the meter's indication of
the position mutually coincide when the select lever is shifted to the “+ (up)” or “- (down)” side (1st ⇔ 6th
gear).
OK or NG
OK >>INSPECTION END
NG >> Check the following.
CVT INDICATOR SYMPTOM CHART
Item name Condition Display value
M GEAR POS During driving 1, 2, 3, 4, 5, 6
Items Presumed location of trouble
The actual gear position does not change, or shifting into the
manual mode is not possible (no gear shifting in the manual mode
possible).
The shift position indicator is not indicated.

Manual mode switch
Refer to CVT-113, "
DTC P0826 MANUAL MODE SWITCH
CIRCUIT" .

CVT main system (Fail-safe function actuated)
Refer to CVT-47, "
SELF-DIAGNOSTIC RESULT MODE" .
The actual gear position changes, but the shift position indicator
is not indicated.Perform the self-diagnosis function.
Refer to CVT-47, "
SELF-DIAGNOSTIC RESULT MODE" .
The actual gear position and the indication on the shift position
indicator do not coincide.Perform the self-diagnosis function.
Refer to CVT-47, "
SELF-DIAGNOSTIC RESULT MODE" .
Only a specific position or positions is/are not indicated on the
shift position indicator.Check the meter control unit.
Refer to DI-4, "
COMBINATION METERS" .

CVT-174
TRANSMISSION CONTROL MODULE

TRANSMISSION CONTROL MODULEPFP:31036
Removal and InstallationBCS0026K
COMPONENTS
REMOVAL
1. Disconnect the battery cable from the negative terminal.
2. Remove Instrument passenger lower panel. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Disconnect connector (1) and (2).
1. TCM 2. ECM
Refer to GI section make sure icons (symbol marks) in the figure. Refer to GI-10, "
Components" .
SCIA7873E
SCIA7874E

TRANSMISSION CONTROL MODULE
CVT-175
D
E
F
G
H
I
J
K
L
MA
B
CVT

4. Disconnect TCM harness connectors (1) and ECM harness
connectors (2).

: nut (2)
5. Remove TCM (1) with ECM (2).

: nut (3)
6. Remove TCM (1) from ECM.
INSTALLATION
Install in the reverse order of removal.
SCIA7875E
SCIA7876E
SCIA7877E

CVT-186
AIR BREATHER HOSE

AIR BREATHER HOSEPFP:31098
Removal and InstallationBCS001MV
COMPONENTS
REMOVAL
Refer to the figure for air breather hose removal procedure.
INSTALLATION
Note the following, and install in the reverse order of removal.

Install air breather hose (1) to air breather tube (2) so that the
paint mark (A) faces leftward. Also make sure air breather hose
end laps with air breather tube 17 mm (0.67 in) or more.

When installing air breather hose (1) to air duct assembly, make
sure to fully insert the hose with clip (2).
1. Air duct assembly 2. Transmission assembly 3. Air breather tube
4. Air breather hose
SCIA7895E
SCIA7896E
SCIA7897E

CVT-198
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsBCS001N1
*1: Refer to MA-14, "Fluids and Lubricants" .
Vehicle Speed at Which Gear Shifting OccursBCS001N2
Numerical value data are reference values.
CAUTION:
Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall SpeedBCS001N3
Line PressureBCS001N4
*1 : Reference values
Solenoid ValvesBCS001N5
Applied modelVQ35DE engine
2WD
CVT modelRE0F09A
CVT assembly Model code number 1XD14
Transmission gear ratioD range Variable
Reverse 1.766
Final drive 5.173
Recommended fluid NISSAN CVT Fluid NS-2*1
Fluid capacity 10.2 liter (9 Imp qt)
CAUTION:

Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid.

Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may
damage the CVT, which is not covered by the warranty.
Engine type Throttle position Shift patternEngine speed (rpm)
At 40 km/h (25 MPH) At 60 km/h (37 MPH)
VQ35DE8/8 “D” position 3,100 - 4,200 4,200 - 5,300
2/8 “D” position 1,200 - 2,000 1,300 - 2,100
Stall speed 2,700 - 3,250 rpm
Engine Engine speedLine pressure kPa (bar, kg/cm2 , psi)
“R”, “D” positions
VQ35DEAt idle speed 750 (7.50, 7.65, 108.8)
At stall speed
5,700 (57.00, 58.14, 826.5)*
1
Name Resistance (Approx.) Terminal
Pressure control solenoid valve B (Secondary
pressure solenoid valve)
3 - 9 Ω3
Pressure control solenoid valve A (Line pressure
solenoid valve)2
Torque converter clutch solenoid valve12
Lock-up select solenoid valve 6 - 19 Ω13

CVT INDICATOR
DI-55
C
D
E
F
G
H
I
J
L
MA
B
DI

4. CHECK SELF-DIAGNOSIS OF TCM.
Perform TCM self-diagnosis. Refer to CVT-43, "
CONSULT-II Function (TRANSMISSION)" .
Self-diagnostic results content
No malfunction detected>> Check TCM input/output signal, and repair or replace malfunctioning parts. Refer
to CVT-40, "
TCM Input/Output Signal Reference Values" .
Malfunction detected>> Check applicable parts, and repair or replace corresponding parts.

DI-76
CAN COMMUNICATION

CAN COMMUNICATIONPFP:23710
System DescriptionBKS003SL
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS003SM
Refer to LAN-49, "CAN System Specification Chart" in “LAN SYSTEM”.

EC-26
[QR]
CAN COMMUNICATION

CAN COMMUNICATIONPFP:23710
System DescriptionBBS005BJ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Refer to LAN-49, "
CAN System Specification Chart" , about CAN communication for detail.

EC-48
[QR]
BASIC SERVICE PROCEDURE


PNP switch: ON

Electric load switch: OFF
(Air conditioner, head lamp, rear window defogger)

Steering wheel: Neutral (Straight-ahead position)

Vehicle speed: Stopped

Transmission: Warmed-up
With CONSULT-II: Drive vehicle until “FLUID TEMP SE” in “DATA MONITOR” mode of “A/T” system indi-
cates less than 0.9V.
Without CONSULT-II: Drive vehicle for 10 minutes.
OPERATION PROCEDURE
With CONSULT-II
1. Perform EC-47, "Accelerator Pedal Released Position Learning" .
2. Perform EC-47, "
Throttle Valve Closed Position Learning" .
3. Start engine and warm it up to normal operating temperature.
4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5. Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode.
6. Touch “START” and wait 20 seconds.
7. Make sure that “CMPLT” is displayed on CONSULT-II screen. If
“CMPLT” is not displayed, Idle Air Volume Learning will not be
carried out successfully. In this case, find the cause of the inci-
dent by referring to the DIAGNOSTIC PROCEDURE below.
8. Rev up the engine two or three times and make sure that idle
speed and ignition timing are within the specifications.
Without CONSULT-II
NOTE:

It is better to count the time accurately with a clock.

It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit
has a malfunction.
SEF217Z
SEF454Y
ITEM SPECIFICATION
Idle speed 700±50 rpm (in P or N position)
Ignition timing 15±5° BTDC (in P or N position)
MBIB0238E

TROUBLE DIAGNOSIS - SPECIFICATION VALUE
EC-95
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EC

TROUBLE DIAGNOSIS - SPECIFICATION VALUEPFP:00031
DescriptionBBS005CB
The specification (SP) value indicates the tolerance of the value that is displayed in “DATA MONITOR (SPEC)”
mode of CONSULT-II during normal operation of the Engine Control System. When the value in “DATA MONI-
TOR (SPEC)” mode is within the SP value, the Engine Control System is confirmed OK. When the value in
“DATA MONITOR (SPEC)” mode is NOT within the SP value, the Engine Control System may have one or
more malfunctions.
The SP value is used to detect malfunctions that may affect the Engine Control System, but will not light the
MI.
The SP value will be displayed for the following three items:

B/FUEL SCHDL (The fuel injection pulse width programmed into ECM prior to any learned on board cor-
rection)

A/F ALPHA-B1 (The mean value of air-fuel ratio feedback correction factor per cycle)

MAS A/F SE-B1 (The signal voltage of the mass air flow sensor)
Testing ConditionBBS005CC

Vehicle driven distance: More than 5,000 km (3,107 miles)

Barometric pressure: 98.3 - 104.3 kPa (0.983 - 1.043 bar, 1.003 - 1.064 kg/cm2 , 14.25 - 15.12 psi)

Atmospheric temperature: 20 - 30°C (68 - 86°F)

Engine coolant temperature: 75 - 95°C (167 - 203°F)

Engine speed: Idle

Transmission: Warmed-up
–After the engine is warmed up to normal operating temperature, drive vehicle until “FLUID TEMP SE” (A/T
fluid temperature sensor signal) indicates more than 60°C (140°F).

Electrical load: Not applied
–Rear window defogger switch, air conditioner switch, lighting switch are OFF. Steering wheel is straight
ahead.
Inspection ProcedureBBS005CD
NOTE:
Perform “DATA MONITOR (SPEC)” mode in maximum scale display.
1. Perform EC-40, "
Basic Inspection" .
2. Confirm that the testing conditions indicated above are met.
3. Select “B/FUEL SCHDL”, “A/F ALPHA-B1” and “MAS A/F SE-
B1” in “DATA MONITOR (SPEC)” mode with CONSULT-II.
4. Make sure that monitor items are within the SP value.
5. If NG, go to EC-96, "
Diagnostic Procedure" .
SEF601Z