cam NISSAN TEANA 2003 Service Manual

EM-202
[VQ]
CAMSHAFT

Summary of the inspection items:
* Transmission/transaxle/CVT fluid. power steering fluid, brake fluid, etc.
Valve ClearanceBBS004W2
INSPECTION
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1. Remove rocker covers (right and left banks). Refer to EM-160, "
ROCKER COVER" .
2. Remove splash guard (RH).
3. Measure the valve clearance as follows:
a. Set No. 1 cylinder at TDC of its compression stroke.

Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) with timing indicator.

Make sure that intake and exhaust cam noses on No. 1 cylin-
der (engine front side of right bank) are located as shown in
the figure.

If not, rotate crankshaft one revolution (360 degrees) and
align as shown in the figure.
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —
SEM713A
SEM918G
SEM418G

CAMSHAFT
EM-203
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

b. Use feeler gauge, measure the clearance between valve lifter
and camshaft.
Valve clearance:
Unit: mm (in)
*: Approximately 80°C (176°F)

By referring to the figure, measure the valve clearances at
locations marked “×” as shown in the table below (locations
indicated in the figure) with feeler gauge.

No. 1 cylinder at compression TDC
c. Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No. 3 cylinder at
TDC of its compression stroke.
NOTE:

To align cylinder No.3 with the compression top dead center,
place matching marks (A) on the crank pulley (1) side and on
the cylinder block side at a point 240°counterclockwise from
the compression top dead center using the hex head of the
crank pulley mounting bolt as aguide.
SEM139D
Cold Hot * (reference data)
Intake 0.26 - 0.34 (0.010 - 0.013) 0.304 - 0.416 (0.012 - 0.016)
Exhaust 0.29 - 0.37 (0.011 - 0.015) 0.308 - 0.432 (0.012 - 0.017)
Measuring position (right bank) No. 1 CYL. No. 3 CYL. No. 5 CYL.
No. 1 cylinder at
compression TDCEXH×
INT×
Measuring position (left bank) No. 2 CYL. No. 4 CYL. No. 6 CYL.
No. 1 cylinder at
compression TDCINT×
EXH×
PBIC2054E
PBIC4628J

EM-204
[VQ]
CAMSHAFT


By referring to the figure, measure the valve clearances at
locations marked “×” as shown in the table below (locations
indicated in the figure).

No. 3 cylinder at compression TDC
d. Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No. 5 cylinder at
TDC of compression stroke.
NOTE:

To align cylinder No.5 with the compression top dead center,
place matching marks (A) on the crank pulley (1) side and on
the cylinder block side at a point 240°counterclockwise from
the compression top dead center using the hex head of the
crank pulley mounting bolt as aguide.
Measuring position (right bank) No. 1 CYL. No. 3 CYL. No. 5 CYL.
No. 3 cylinder at
compression TDCEXH×
INT×
Measuring position (left bank) No. 2 CYL. No. 4 CYL. No. 6 CYL.
No. 3 cylinder at
compression TDCINT×
EXH ×
PBIC2055E
PBIC4628J

CAMSHAFT
EM-205
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM


By referring to the figure, measure the valve clearances at
locations marked “×” as shown in the table below (locations
indicated in the figure).

No. 5 cylinder at compression TDC
4. For the measured value are out of the standard, perform adjustment. Refer to EM-205, "
ADJUSTMENT" .
ADJUSTMENT

Perform adjustment depending on selected head thickness of valve lifter.
1. Remove camshaft. Refer to EM-192, "
REMOVAL" .
2. Remove valve lifters at the locations that are out of the standard.
3. Measure the center thickness of removed valve lifters with
micrometer.
4. Use the equation below to calculate valve lifter thickness for replacement.
Measuring position (right bank) No. 1 CYL. No. 3 CYL. No. 5 CYL.
No. 5 cylinder at
compression TDCEXH×
INT×
Measuring position (left bank) No. 2 CYL. No. 4 CYL. No. 6 CYL.
No. 5 cylinder at
compression TDCINT×
EXH ×
PBIC2056E
KBIA0057E
Valve lifter thickness calculation: t = t1 + (C1 – C2 )
t = Valve lifter thickness to be replaced
t
1 = Removed valve lifter thickness
C
1= Measured valve clearance
C
2= Standard valve clearance:
Intake : 0.30 mm (0.012 in)*
Exhaust : 0.33 mm (0.013 in)*
*: Approximately 20°C (68°F)

EM-206
[VQ]
CAMSHAFT


Thickness of new valve lifter can be identified by stamp marks
on the reverse side (inside the cylinder).
VQ23DE
Available thickness of valve lifter: 27 sizes with range 6.66 to 7.18 mm (0.2622 to 0.2827 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to EM-258, "
Available Valve Lifter" .
VQ35DE
Available thickness of valve lifter: 27 sizes with range 7.88 to 8.40 mm (0.3102 to 0.3307 in) in steps of
0.02 mm (0.0008 in) (when manufactured at factory). Refer to EM-258, "
Available Valve Lifter" .
CAUTION:
Install identification letter at the end, “U” and “R”, at each of proper positions. (Be careful of
mis-installation between intake and exhaust)
5. Install selected valve lifter.
6. Install camshaft. Refer to EM-197, "
INSTALLATION" .
7. Manually rotate crankshaft pulley a few rotations.
8. Make sure that the valve clearances for cold engine are within the specifications by referring to the speci-
fied values. Refer to EM-202, "
INSPECTION" .
9. Install all removed parts in the reverse order of removal. Refer to EM-197, "
INSTALLATION" .
10. Warm up the engine, and check for unusual noise and vibration.
KBIA0119E
Stamp mark
Thickness
INT EXH
666U 6.66 mm
668U 6.68 mm
··
··
718U 7.18 mm
Stamp mark
Thickness
INT EXH
788U 788R 7.88 mm
790U 790R 7.90 mm
·· ·
·· ·
840U 840R 8.40 mm

OIL SEAL
EM-207
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

OIL SEALPFP:00100
Removal and Installation of Valve Oil SealBBS004W3
REMOVAL
1. Remove engine assembly from vehicle, and separate front suspension member and transaxle from
engine. Refer to EM-223, "
ENGINE ASSEMBLY" .
2. Install engine sub-attachment with engine stand shaft [SST: KV10117001 and KV10106500] to right side
of cylinder block, then lift engine, and mount it onto engine stand [SST: ST0501S000]. Refer to EM-228,
"CYLINDER BLOCK" .
3. Remove camshaft relating to valve oil seal to be removed. Refer to EM-192, "
CAMSHAFT" .
4. Remove valve lifters. Refer to EM-192, "
CAMSHAFT" .
5. Rotate crankshaft until the cylinder requiring new oil seals is at TDC. This will prevent valve from dropping
into cylinder.
6. Remove valve collet.

Compress valve spring with valve spring compressor, attach-
ment, adapter (SST). Remove valve collet with magnet hand.
CAUTION:
When working, take care not to damage valve lifter holes.
7. Remove valve spring retainer and valve spring.
8. Remove valve oil seal using valve oil seal puller (SST).
INSTALLATION
1. Apply engine oil on new valve oil seal joint and seal lip.
2. Using valve oil seal drift (SST), press-fit valve seal to height “H”
shown in the figure.
NOTE:
Dimension “H”: Height measured before valve spring seat instal-
lation
3. Install in the reverse order of removal after this step.
PBIC1791E
PBIC1610E
Intake and exhaust : 14.3 - 14.9 mm (0.563 - 0.587 in)
PBIC1611E

EM-212
[VQ]
CYLINDER HEAD

3. Remove camshaft. Refer to EM-192, "CAMSHAFT" .
4. Remove engine slingers.
5. Remove the following:

Fuel tube and fuel injector assembly; Refer to EM-155, "FUEL INJECTOR AND FUEL TUBE" .

Intake manifold; Refer to EM-138, "INTAKE MANIFOLD" .

Exhaust manifold; Refer to EM-140, "EXHAUST MANIFOLD AND THREE WAY CATALYST" .

Water inlet and thermostat assembly; Refer to CO-50, "WATER INLET AND THERMOSTAT ASSEM-
BLY" .

Water outlet, water bypass pipe, heater pipe and water connector; Refer to CO-52, "WATER OUTLET
AND WATER PIPING" .
6. Remove cylinder head bolts in the reverse order as shown in the
figure with cylinder head bolt wrench (commercial service tool)
to remove cylinder heads (right and left banks).
7. Remove cylinder head gaskets.
INSPECTION AFTER REMOVAL
Cylinder Head Bolts Outer Diameter

Cylinder head bolts are tightened by plastic zone tightening
method. Whenever the size difference between “d1” and “d2”
exceeds the limit, replace them with new one.

If reduction of outer diameter appears in a position other than
“d2”, use it as “d2” point.
PBIC2057E
Limit (“d1” – “d2”) : 0.11 mm (0.0043 in)
PBIC2480E

EM-220
[VQ]
CYLINDER HEAD

5. Using valve guide drift (commercial service tool), press valve
guide from camshaft side to the dimensions as in the figure.
CAUTION:
Cylinder head contains heat. When working, wear protec-
tive equipment to avoid getting burned.
6. Using valve guide reamer (commercial service tool), apply
reamer finish to valve guide.
VALVE SEAT CONTACT

After confirming that the dimensions of valve guides and valves
are within the specifications, perform this procedure.

Apply prussian blue (or white lead) onto contacting surface of
valve seat to check the condition of the valve contact on the sur-
face.

Check if the contact area band is continuous all around the cir-
cumference.

If not, grind to adjust valve fitting and check again. If the contact-
ing surface still has “NG” conditions even after the re-check,
replace valve seat. Refer to EM-220, "
VALVE SEAT REPLACE-
MENT" .
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with oversized [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this. Refer to EM-262, "
Va l v e S e a t" .
CAUTION:
Prevent to scratch cylinder head by excessive boring.
2. Ream cylinder head recess diameter for service valve seat.

Be sure to ream in circles concentric to valve guide center.
This will enable valve to fit correctly.Projection “L”
Intake and exhaust
: 12.6 - 12.8 mm (0.496 - 0.504 in)
SEM950E
Standard:
Intake and exhaust
: 6.000 - 6.018 mm (0.2362 - 0.2369 in)
SEM932C
SBIA0322E
Oversize [0.5 mm (0.020 in)]
Intake
VQ23DE : 35.500 - 35.516 mm (1.3976 - 1.3983 in)
VQ35DE : 38.500 - 38.516 mm (1.5157 - 1.5164 in)
Exhaust
VQ23DE : 30.500 - 30.516 mm (1.2008 - 1.2014 in)
VQ35DE : 32.700 - 32.716 mm (1.2874 - 1.2880 in)
SEM795A

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-257
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

CAMSHAFT AND CAMSHAFT BEARING
Unit: mm (in)
*
1 : Cam wear limit
*2 : Total indicator reading
Valve Lifter
Unit: mm (in)
Valve Clearance
Unit: mm (in)
*: Approximately 80°C (176°F) ItemsStandard
Limit
VQ23DE VQ35DE
Camshaft journal oil clearanceNo. 1 0.045 - 0.086 (0.0018 - 0.0034)
0.15 (0.0059)
No. 2, 3, 4 0.035 - 0.076 (0.0014 - 0.0030)
Camshaft bracket inner diameterNo. 1 26.000 - 26.021 (1.0236 - 1.0244) —
No. 2, 3, 4 23.500 - 23.521 (0.9252 - 0.9260) —
Camshaft journal diameterNo. 1 25.935 - 25.955 (1.0211 - 1.0218) —
No. 2, 3, 4 23.445 - 23.465 (0.9230 - 0.9238) —
Camshaft end play 0.115 - 0.188 (0.0045 - 0.0074) 0.24 (0.0094)
Camshaft cam height “A”Intake44.265 - 44.455
(1.7427 - 1.7502)44.865 - 45.055
(1.7663 - 1.7738)
0.2 (0.008)*
1
Exhaust43.405 - 43.595
(1.7089 - 1.7163)44.865 - 45.055
(1.7663 - 1.7738)
Camshaft runout [TIR*
2 ]Less than 0.02 (0.0010) 0.05 (0.0020)
Camshaft sprocket runout [TIR*
2 ]— 0.15 (0.0059)
SEM671
ItemsStandard
VQ23DE VQ35DE
Valve lifter outer diameter 29.977 - 29.987 (1.1802 - 1.1806) 33.977 - 33.987 (1.3377 - 1.3381)
Valve lifter hole diameterIntake 30.015 - 30.031 (1.1817 - 1.1823)
34.000 - 34.016 (1.3386 - 1.3392)
Exhaust 30.003 - 30.019 (1.1812 - 1.1818)
Valve lifter clearanceIntake 0.028 - 0.054 (0.0011 - 0.0021)
0.013 - 0.039 (0.0005 - 0.0015)
Exhaust 0.016 - 0.042 (0.0006 - 0.0017)
Items Cold Hot* (reference data)
Intake 0.26 - 0.34 (0.010 - 0.013) 0.304 - 0.416 (0.012 - 0.016)
Exhaust 0.29 - 0.37 (0.011 - 0.015) 0.308 - 0.432 (0.012 - 0.017)

FSU-1
FRONT SUSPENSION
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION FSU
A
B
FSU

FRONT SUSPENSION
PRECAUTIONS .......................................................... 2
Caution ..................................................................... 2
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 4
NVH Troubleshooting Chart ..................................... 4
FRONT SUSPENSION ASSEMBLY ........................... 5
On-Vehicle Inspection .............................................. 5
INSPECTION OF TRANSVERSE LINK BALL
JOINT END PLAY ................................................. 5
STRUT INSPECTION ........................................... 5
Wheel Alignment Inspection ..................................... 5
DESCRIPTION ...................................................... 5
PRELIMINARY CHECK ........................................ 5
INSPECTION OF CAMBER, CASTER AND
KINGPIN INCLINATION ANGLES. ....................... 5
Components ............................................................. 7
Removal and Installation .......................................... 8
REMOVAL ............................................................. 8
INSTALLATION ..................................................... 9
COIL SPRING AND STRUT ..................................... 10
Removal and Installation ........................................ 10
REMOVAL ........................................................... 10INSTALLATION ................................................... 11
Disassembly and Assembly .................................... 11
DISASSEMBLY ................................................... 11
INSPECTION AFTER DISASSEMBLY ................ 12
ASSEMBLY ......................................................... 12
TRANSVERSE LINK ................................................. 14
Removal and Installation ........................................ 14
REMOVAL ........................................................... 14
INSPECTION AFTER REMOVAL ....................... 14
INSTALLATION ................................................... 15
STABILIZER BAR ..................................................... 16
Removal and Installation ........................................ 16
REMOVAL ........................................................... 16
INSPECTION AFTER REMOVAL ....................... 16
INSTALLATION ................................................... 16
FRONT SUSPENSION MEMBER ............................. 17
Removal and Installation ........................................ 17
REMOVAL ........................................................... 17
INSPECTION AFTER REMOVAL ....................... 17
INSTALLATION ................................................... 17
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 18
Wheel Alignment (Unladen*) .................................. 18
Ball Joint ................................................................. 18
Wheelarch Height (Unladen*) ................................. 18