Oil NISSAN TEANA 2003 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 1159 of 3502
DTC P1777 STEP MOTOR - CIRCUIT
CVT-153
D
E
F
G
H
I
J
K
L
MA
B
CVT
DTC P1777 STEP MOTOR - CIRCUITPFP:31020
DescriptionBCS001LS
The step motor changes the step with turning 4 coils ON/OFF according to the signal from TCM. As a result,
the flow of line pressure to primary pulley is changed and pulley ratio is controlled.
CONSULT-II Reference ValueBCS001LT
Remarks: Specification data are reference values.
On Board Diagnosis LogicBCS001LU
Diagnostic trouble code “P1777 STEP MOTR CIRC” with CONSULT-II is detected under the following condi-
tions.
When operating step motor ON and OFF, there is no proper change in the voltage of TCM terminal which
corresponds to it.
Possible CauseBCS001LV
Step motor
Harness or connectors
(Step motor circuit is open or shorted.)
DTC Confirmation ProcedureBCS001LW
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, touch “ERASE” on “SELF-DIAG RESULTS” and then perform the following procedure to con-
firm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON and select “DATA MONITOR” mode for
“TRANSMISSION” with CONSULT-II.
2. Drive vehicle for at least 5 consecutive seconds.
3. If DTC is detected, go to CVT-155, "
Diagnostic Procedure" .
Item name Condition Display value (Approx.)
STM STEP
During driving−20 step - 190 step
SMCOIL A
Changes ON⇔OFF SMCOIL B
SMCOIL C
SMCOIL D
BCIA0031E
Page 1161 of 3502
DTC P1777 STEP MOTOR - CIRCUIT
CVT-155
D
E
F
G
H
I
J
K
L
MA
B
CVT
TCM terminals data are reference values.
Diagnostic ProcedureBCS001LY
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine.
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “TRANSMISSION” with CONSULT-II.
3. Start vehicle and read out the value of “STM STEP”, “SMCOIL
A”, “SMCOIL B”, “SMCOIL C”, and “SMCOIL D”.
OK or NG
OK >> GO TO 4.
NG >> GO TO 2.
2. CHECK HARNESS BETWEEN TCM AND STEP MOTOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector and TCM connector.
3. Check continuity between TCM connector terminals and CVT
unit harness connector terminals.
4. If OK, check harness for short to ground and short to power.
5. If OK, check continuity between body ground and CVT assembly.
6. Reinstall any part removed.
OK or NG
OK >> GO TO 3.
NG >> Repair open circuit or short to ground or short to power in harness or connectors.
Terminal Wire color Item Condition Data (Approx.)
11 G/R Step motor A Within 2 seconds after ignition switch ON, the time measure-
ment by using the pulse width measurement function (Hi level) of
CONSULT-II.*1
CAUTION:
Connect the diagnosis data link cable to the vehicle diagno-
sis connector.
*1: A circuit tester cannot be used to test this item.30.0 msec
12 O/B Step motor B10.0 msec
20 R Step motor C30.0 msec
21 R/G Step motor D10.0 msec
Item name Condition Display value (Approx.)
STM STEP
During driving−20 step - 190 step
SMCOIL A
Changes ON⇔OFF SMCOIL B
SMCOIL C
SMCOIL D
SCIA4516E
Item Connector Terminal Continuity
TCM F106 11
Ye s
CVT unit harness connector F49 6
TCM F106 12
Ye s
CVT unit harness connector F49 7
TCM F106 20
Ye s
CVT unit harness connector F49 8
TCM F106 21
Ye s
CVT unit harness connector F49 9
SCIA4695E
Page 1193 of 3502
DIFFERENTIAL SIDE OIL SEAL
CVT-187
D
E
F
G
H
I
J
K
L
MA
B
CVT
DIFFERENTIAL SIDE OIL SEALPFP:33111
Removal and InstallationBCS001MW
COMPONENTS
REMOVAL
1. Remove drive shaft assembly. Refer to FA X - 8 , "FRONT DRIVE
SHAFT" .
2. Remove differential side oil seals using a flat-bladed screw-
driver.
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
1. Transaxle assembly 2. Differential side oil seal
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-10, "
Components" .
However, refer to the following symbols for others.
: Apply CVT Fluid NS-2.
SCIA7917E
SCIA2412E
Page 1194 of 3502
CVT-188
DIFFERENTIAL SIDE OIL SEAL
INSTALLATION
1. As shown below, use a drift to drive the differential side oil seal
into the case until it is flush. Refer to dimensions A.
Unit: mm (in)
NOTE:
The differential side oil seal pulling direction is used as the refer-
ence.
Drift to be used:
CAUTION:
When installing differential side oil seals, apply NISSAN CVT Fluid NS-2.
Do not reuse differential side oil seals.
2. Reinstall any part removed.
CAUTION:
If lubricant leak has occurred, after finishing work, check fluid level. Refer to CVT-13, "
Checking
CVT Fluid" .
Dimensions A 0±0.5 (0±0.020)
SCIA7918E
Location Tool number: A
Transaxle case side (left)
ST33400001
Converter housing side (right)
SCIA6583E
Page 1200 of 3502
CVT-194
TRANSAXLE ASSEMBLY
REMOVAL
CAUTION:
The transaxle assembly itself cannot be removed from the vehicle. Remove the transaxle assembly
and engine assembly together from the vehicle.
1. Disconnect the batter cable from the negative terminal.
2. Remove engine undercover.
3. Remove exhaust front tube with power tool. Refer to EX-2, "
Removal and Installation" .
4. Remove rear plate cover. Refer to EM-145, "
Removal and
Installation" .
5. Turn crankshaft, and remove the four tightening nuts for drive
plate and torque converter.
CAUTION:
The crankshaft should be rotated clockwise, viewed from
the front of the engine.
6. Remove the four bolts in the figure.
7. Remove transaxle assembly and engine assembly together
from the vehicle. Refer to EM-223, "
Removal and Installation" .
8. Remove drive shaft. Refer to FA X - 11 , "
Removal and Installation
(LH)" .
CAUTION:
Be sure to replace the differential side oil seal with new one
at the every removal of drive shaft. Refer to CVT-187,
"Removal and Installation" .
9. Remove rear gusset.
10. Remove CVT fluid level gauge.
11. Remove CVT fluid charging pipe.
12. Remove O-ring from CVT fluid charging pipe.
13. Disconnect harness connector and wire harness.
SCIA6475E
SCIA1861E
SCIA1893E
SCIA1894E
Page 1207 of 3502
DI-1
DRIVER INFORMATION SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION DI
A
B
DI
DRIVER INFORMATION SYSTEM
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
COMBINATION METERS ........................................... 4
System Description .................................................. 4
UNIFIED METER CONTROL UNIT ...................... 4
UNIFIED METER AND A/C AMP. ......................... 4
FAIL-SAFE ............................................................ 5
HOW TO CHANGE THE DISPLAY FOR ODO/
TRIP METER ........................................................ 6
POWER SUPPLY AND GROUND CIRCUIT ........ 6
SPEEDOMETER ................................................... 7
TACHOMETER ..................................................... 7
LOW WATER TEMPERATURE INDICATOR
LAMP, HIGH WATER TEMPERATURE WARN-
ING LAMP ............................................................. 7
FUEL GAUGE ....................................................... 7
Component Parts and Harness Connector Location ..... 7
Arrangement of Combination Meter ......................... 8
Internal Circuit .......................................................... 9
Wiring Diagram — METER — ................................ 10
Terminals and Reference Value for Combination
Meter ...................................................................... 12
Terminals and Reference Value for Unified Meter
and A/C Amp. ......................................................... 13
Self-Diagnosis Mode of Combination Meter ........... 13
SELF-DIAGNOSIS MODE FUNCTION ............... 13
OPERATION PROCEDURE ............................... 13
CONSULT-II Function ............................................ 14
Trouble Diagnosis .................................................. 14
HOW TO PROCEED WITH TROUBLE DIAGNO-
SIS ...................................................................... 14
PRELIMINARY CHECK ...................................... 15
SYMPTOM CHART 1 .......................................... 17
SYMPTOM CHART 2 .......................................... 17
Power Supply and Ground Circuit Inspection ........ 18
Vehicle Speed Signal Inspection ............................ 20
Engine Speed Signal Inspection ............................ 21
Engine Coolant Temperature Signal Inspection ..... 21Fuel Level Sensor Signal Inspection ...................... 22
Fuel Gauge Does Not Move to FULL position ........ 23
Electrical Components Inspection .......................... 24
CHECK FUEL LEVEL SENSOR UNIT ................ 24
Removal and Installation of Combination Meter ..... 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Disassembly and Assembly of Combination Meter ... 25
DISASSEMBLY ................................................... 26
ASSEMBLY ......................................................... 26
UNIFIED METER AND A/C AMP .............................. 27
System Description ................................................. 27
INPUT/OUTPUT SIGNALS ................................. 27
Schematic ............................................................... 28
CONSULT-II Function (METER A/C AMP) ............. 29
CONSULT-II BASIC OPERATION ....................... 29
SELF-DIAGNOSTIC RESULTS ........................... 29
DATA MONITOR ................................................. 30
DTC [U1000] CAN Communication Circuit ............. 32
DTC [B2202] Meter Communication Circuit ........... 32
DTC [B2205] Vehicle Speed Circuit ........................ 34
Removal and Installation of Unified Meter and A/C
Amp. ....................................................................... 34
REMOVAL ........................................................... 34
INSTALLATION ................................................... 34
WARNING LAMPS .................................................... 35
System Description ................................................. 35
OIL PRESSURE WARNING LAMP ..................... 35
Schematic ............................................................... 36
Wiring Diagram — WARN — .................................. 37
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) ............................................................. 45
Oil Pressure Warning Lamp Does Not Turn Off (Oil
Pressure Is Normal) ................................................ 46
Electrical Component Inspection ............................ 47
OIL PRESSURE SWITCH ................................... 47
A/T INDICATOR ........................................................ 48
Wiring Diagram — AT/IND — ................................. 48
A/T Indicator Is Malfunction .................................... 50
CVT INDICATOR ....................................................... 52
Page 1211 of 3502
COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI
FA I L - S A F E
Solution When Communication Error Between the Unified Meter and A/C Amp. and the Com-
bination Meter
Function Specifications
SpeedometerReturn to zero when discontinuing communication or receiv-
ing irregular data.
Tachometer
Reset to zero by suspending communication.
Fuel gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
Shift indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lampLow water temperature indicator lamp
The lamp turns on by suspending communication. VDC OFF indicator (With VDC)
SLIP indicator (With VDC)
Brake warning lamp
ABS warning lamp
ASCD CRUISE indicator lamp
The lamp turns off by suspending communication. ASCD SET indicator lamp
Turn signal indicator lamp
High-beam indicator lamp
Front fog indicator lamp
Rear fog indicator lamp
Oil pressure warning lamp
Door warning lamp
High water temperature warning lamp
Malfunction indicator lamp
A/T CHECK warning lamp
CVT indicator lamp
KEY warning lamp
LOCK warning lamp
Page 1221 of 3502
COMBINATION METERS
DI-15
C
D
E
F
G
H
I
J
L
MA
B
DI
PRELIMINARY CHECK
1. CHECK SELF-DIAGNOSIS RESULT OF UNIFIED METER AND A/C AMP.
1. Start engine.
2. Select “METER A/C AMP” on COSULT-II, and perform self-diagnosis of unified meter and A/C amp. Refer
to DI-29, "
CONSULT-II Function (METER A/C AMP)"
3. After erasing the self-diagnosis result, perform self-diagnosis again.
Self-diagnosis results content
No malfunction detected >> GO TO 2.
Malfuction detected >> GO TO DI-17, "
SYMPTOM CHART 2" .
2. CHECK WARNING LAMP ILLUMINATION
1. Turn ignition switch ON.
2. Make sure warninig lamps (such as malfunction indicator lamp and oil pressure warning lamp) illuminate.
Do warninig lamps illuminate?
OK >> GO TO 3.
NG >> Check ignition power supply system of combination meter.
3. CHECK SELF-DIAGNOSIS OPERATION OF COMBINATION METER
Perform combination meter self-diagnosis. Refer to DI-13, "
OPERATION PROCEDURE" .
Does self-diagnosis function operate?
OK >> GO TO 4.
NG >> Check battery power supply of combinatiom meter and ground circuit.
4. CHECK COMBINATION METER CIRCUIT
Check indication of each meter/gauge in self-diagnosis mode.
OK or NG
OK >> GO TO 5
NG >> Replace combination meter.
5. CHECK LOW-FUEL WARNING LAMP ILLUMINATION
While checking low-fuel warning lamp check, confirm illumination of low-fuel warning lamp.
Does low
-fuel warning lamp illuminate (while not pushing odo/trip meter switch)?
YES >> GO TO 6.
NO >> Replace combination meter.
Condition of odo/trip meter switch Low-fuel warning lamp
Pressed Does not illuminate.
Released Illuminates.
Page 1233 of 3502
UNIFIED METER AND A/C AMP
DI-27
C
D
E
F
G
H
I
J
L
MA
B
DI
UNIFIED METER AND A/C AMPPFP:27760
System DescriptionBKS001SK
For the unified meter and A/C amp., the signal required for con-
trolling the combination meter are integrated in the A/C auto
amp.
Unified meter and A/C amp. controls each operation for A/C
auto amp. For information regarding A/C control, refer to AT C -
24, "AIR CONDITIONER CONTROL" .
Unified meter and A/C amp. inputs necessary information for
combination meter from each unit by CAN communication and
so on.
And unified meter and A/C amp. outputs these signals using
communication line (TX, RX) between unified meter and A/C
amp. and combination meter.
The signals required for the distance to empty (DTE) display are centralized in the unified meter and A/C
amp., converted into data, and sent to the display unit (with display unit) using CAN communication.
Other input signals are also sent to the ECM, TCM, BCM and display unit (with display unit) using CAN
communication.
The unified meter and A/C amp. correspond a CONSULT-II function (self-diagnostic results, CAN diag-
nostic support monitor and data monitor).
INPUT/OUTPUT SIGNALS
Between Unified Meter and A/C amp. and Combination Meter
SKIB0778E
Unit Input Output
Unified meter and A/C amp.
Seat belt buckle switch signal (Driver's side)
Parking brake signal
Illumination control nighttime required signal
Refuel status signal
Low-fuel warning lamp condition signal
Combination meter receive error signal
Delivery destination data signal
Combination meter specifications signal
Vehicle speed signal (8-pulse)
Engine speed signal
Engine coolant temperature signal
Fuel level sensor signal (resistance value)
Malfunction indicator lamp signal
ABS warning lamp signal
Brake warning lamp signal
KEY warning lamp signal (With Intelligent Key)
LOCK warning lamp signal (With Intelligent Key)
High-beam request signal
Turn indicator signal
VDC OFF indicator lamp signal (With VDC)
SLIP indicator lamp signal (With VDC)
ASCD CRUISE indicator lamp signal
ASCD SET indicator lamp signal
A/T position indicator signal
A/T CHECK warning lamp signal
CVT indicator lamp signal
CVT position indicator signal
Door switch signal
Oil pressure switch signal
Position lights request signal
Front fog light request signal
Rear fog light request signal
Buzzer output signal
Page 1236 of 3502
DI-30
UNIFIED METER AND A/C AMP
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on the “DATA MONITOR” screen.
3. When “SELECTION FROM MENU” is selected, touch individual
items to be monitored. When “MAIN SIGNALS” is selected,
main items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the moni-
tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
MAIN SIGNALS Monitors main signals.
SELECTION FROM MENU Selects and monitors individual signal.
SKIA8739E
Monitor item [Unit] MAIN SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] or [mph] X XThis is the angle correction value after the speed signal from
the ABS actuator and electric unit (control unit) is converted
into the vehicle speed.
SPEED OUTPUT [km/h] or [mph] X XThis is the angle correction value before the speed signal
from the ABS actuator and electric unit (control unit) is con-
verted into the vehicle speed.
TACHO METER [rpm] X XThis is the converted value for the engine speed signal from
the ECM.
W TEMP METER [°C] or [°F] X XThis is the converted value for the engine coolant tempera-
ture signal from the ECM.
FUEL METER [lit.] X XThis is the processed value for the signal (resistance value)
from the fuel gauge.
DISTANCE [km] or [mile] X XThis is the calculated value for the speed signal from the
ABS actuator and electric unit (control unit), the signal
(resistance signal) from the fuel gauge and fuel consumption
signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
MIL [ON/OFF] X Indicates [ON/OFF] condition of malfunction indicator lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high-beam indicator.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
FR FOG IND X Indicates [ON/OFF] condition of front fog lamp indicator.
RR FOG IND X Indicates [ON/OFF] condition of rear fog lamp.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
LIGHT IND [ON/OFF] X Indicates [ON/OFF] condition of light indicator lamp.
VDC/TCS IND [ON/OFF] X Indicates [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Indicates [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (green).