Oil NISSAN TEANA 2003 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 650 of 3502
BCS-8
BCM (BODY CONTROL MODULE)
SYSTEMS CONTROLLED BY BCM DIRECTLY
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER
SYSTEMS CONTROLLED BY BCM, COMBINATION METER AND IPDM E/R
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT
System Reference
Power door lock systemBL-21, "
POWER DOOR LOCK SYSTEM"
Remote keyless entry systemBL-46, "REMOTE KEYLESS ENTRY SYSTEM"
Power window system NOTEGW-17, "POWER WINDOW SYSTEM"
Sunroof NOTERF-10, "SUNROOF"
Interior room lamp timerLT-219, "INTERIOR ROOM LAMP"
Interior room lamp battery saver controlLT-222, "INTERIOR ROOM LAMP BATTERY SAVER CONTROL"
Rear fog lampLT-142, "REAR FOG LAMP"
System Reference
NATSBL-139, "
NATS(Nissan Anti-Theft System)"
HeadlampLT- 6 , "HEADLAMP - XENON TYPE -"
LT-38, "HEADLAMP - HALOGEN TYPE -"
Auto light systemLT-64, "AUTO LIGHT SYSTEM"
Parking, license plate and tail lamps LT-196, "PARKING, LICENSE PLATE AND TAIL LAMPS"
Front fog lampLT-126, "FRONT FOG LAMP"
Exterior lamp battery saver controlLT-197, "EXTERIOR LAMP BATTERY SAVER CONTROL"
Front wiper and washer systemWW-4, "FRONT WIPER AND WASHER SYSTEM"
Headlamp washerWW-40, "HEADLAMP WASHER"
Rear window defoggerGW-54, "REAR WINDOW DEFOGGER"
System Reference
Warning chimeDI-56, "
WARNING CHIME"
Turn signal and hazard warning lampsLT-152, "TURN SIGNAL AND HAZARD WARNING LAMPS"
System Reference
Oil pressure warning lampDI-35, "
WARNING LAMPS"
System Reference
Intelligent Key systemBL-68, "
INTELLIGENT KEY SYSTEM"
Page 652 of 3502
BCS-10
BCM (BODY CONTROL MODULE)
CAN Communication UnitBKS001UH
Refer to LAN-49, "CAN System Specification Chart" .
Rear fog lamp Combination switch
Rear fog lamp
Combination meter
(Rear fog lamp indicator)
Turn signal lamp
Combination switch
Ignition switch (ON)
Turn signal lamp
Combination meter
(turn signal indicator, warning chime)
Hazard lamp Hazard switch
Turn signal lamp
Combination meter
(turn signal indicator, warning chime)
Interior room lamp timer
Key switch
Remote keyless entry receiver
Power window main switch
(door lock and unlock switch)
Front door lock assembly (driver side)
Front door switch (driver side)
Front door switch (passenger side)
Rear door switch LH
Rear door switch RH
Ignition switch (ON)
Map lamp
Personal lamp RH
Personal lamp LH
Ignition keyhole illumination
Key warning chime
Key switch
Front door switch (driver side)
Ignition switch (ON)Combination meter (warning buzzer)
Light warning chime
Combination switch
Front door switch (driver side)
Ignition switch (ON)Combination meter (warning buzzer)
Oil pressure warning lamp
IPDM E/R
Ignition switch (ON)Combination meter (warning lamp)
Front wiper and washer system
Combination switch
Combination meter
Ignition switch (ON)IPDM E/R
Headlamp washer
Headlamp washer switch
Combination switch
Ignition switch (ON)IPDM E/R
Rear window defogger
Rear window defogger switch
Ignition switch (ACC, ON)IPDM E/R
A/C switch signal
Unified meter and A/C amp.
Ignition switch (ON)ECM
Blower fan switch signal
Unified meter and A/C amp.
Ignition switch (ON)ECM System Input Output
Page 655 of 3502
BCM (BODY CONTROL MODULE)
BCS-13
C
D
E
F
G
H
I
J
L
MA
B
BCS
CONSULT-II Function (BCM)BKS001UK
CONSULT-II can display each diagnostic item using the diagnostic test mode shown following.
CONSULT-II BASIC OPERATION
Refer to GI-34, "CONSULT-II Start Procedure" .
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
×:Applicable
NOTE:
This item is displayed, but should not be used.BCM diagnostic test item Check item, diagnostic test mode Content
Inspection by partWORK SUPPORT Changes setting of each function.
SELF-DIAGNOSIS RESULTS BCM performs self-diagnosis of CAN communication.
DATA MONITOR Displays the input data of BCM in real time.
CAN DIAG SUPPORT MNTRThe result of transmit/receive diagnosis of CAN communication
can be read.
ACTIVE TEST Gives a drive signal to a load to check the operation.
ECU PART NUMBER ECM part number can be read.
CONFIGURATION (Not be used.)
CONSULT-II display System and itemDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSDATA
MONITORCAN
DIAG
SUP-
PORT
MNTRACTIVE
TESTECU
PA R T
NUMBERCON-
FIGU-
RATION
BCM BCM×× × ×
×
NOTE
DOOR LOCK Power door lock system×××
REAR DEFOGGER Rear window defogger××
BUZZER Warning chime××
INT LAMP Room lamp timer×××
MULTI REMOTE ENTRemote keyless entry
system×××
HEAD LAMP Headlamp×××
WIPER Wiper×××
FLASHERTurn signal lamp
Hazard lamp××
AIR CONDITONERBlower fan switch signal
A/C switch signal×
INTELLIGENT KEY Intelligent Key system×
COMB SW Combination switch×
IMMU NATS××
BATTERY SAVER Room lamp battery saver×× ×
TRUNK Trunk lid opener××
SIGNAL BUFFER Oil pressure switch××
PANIC ALARM Panic alarm×
Page 821 of 3502
PRECAUTIONS
BR-3
C
D
E
G
H
I
J
K
L
MA
B
BR
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000BB
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000BC
Clean dust on front brake and rear brake with a vacuum dust collector. Do not blow with compressed air.
Recommended fluid is brake fluid “DOT 3 or DOT 4”. Refer to MA-14, "Fluids and Lubricants" .
Do not reuse drained brake fluid.
Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is splashed
on painted surfaces of body, immediately wipe it off and them wash it away with water immediately.
To clean or wash all parts of master cylinder, disc brake caliper, use clean brake fluid.
Do not use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system.
Use a flare nut torque wrench when installing brake tube.
When installing brake tube, be sure to check torque.
Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery cables.
Burnish the brake contact surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low
mileage. Refer to BR-32, "
BRAKE BURNISHING PROCE-
DURE" (Front disc brake), BR-39, "BRAKE BURNISHING
PROCEDURE" (Rear disc brake).
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with a dust collector.
SBR820BA
Page 833 of 3502
BRAKE MASTER CYLINDER
BR-15
C
D
E
G
H
I
J
K
L
MA
B
BR
Disassembly and AssemblyBFS000BR
COMPONENTS
1. Reservoir tank 2. Reservoir cap 3. Oil strainer
(Models with VDC)
4. Pin 5. Cylinder body 6. Piston stopper
(Models with VDC)
7. Grommet 8. Secondary piston assembly 9. Primary piston assembly
10. O-ring 11. Snap ring 12. Guide assembly
13. Plate 14. Stopper cap
Refer to GI-10, "
Components" and the followings for the symbols in the figure.
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
: Apply brake fluid.
PFIA0822E
Page 834 of 3502
BR-16
BRAKE MASTER CYLINDER
MODELS WITHOUT VDC
CAUTION:
Remove reservoir tank only when absolutely necessary.
Disassembly (Piston Assembly)
1. Using a flat-bladed screwdriver as shown in the figure, lift up
tabs on stopper cap and remove it from master cylinder.
NOTE:
Remove stopper cap while holding it because primary piston
assembly in master cylinder may pop out.
2. Carefully pull primary piston assembly straight out to prevent
cylinder inner wall from being damaged.
3. Tap flange using a soft block, such as wood, and carefully pull
secondary piston assembly straight out to prevent cylinder body
inner wall from being damaged.
Inspection After Disassembly (Piston Assembly)
Cylinder body
Check a inner wall of cylinder for damage, abrasions, corrosion, and pinholes. Replace cylinder body if
detected.
Assembly (Piston Assembly)
CAUTION:
Do not use mineral oils such as kerosene, gasoline during the cleaning and assembly process.
Make sure there is no foreign matter such as dirt or dust attached to inner cylinder walls, piston,
or cap seal, and use care to avoid damaging parts with the assembly tools.
Do not drop parts. If a part is dropped, do not use it.
1. Apply brake fluid to cylinder inner wall, piston cups and contact
surfaces between piston assemblies. Then insert secondary pis-
ton assembly and primary piston assembly into cylinder body in
this order.
CAUTION:
Do not reuse primary and secondary piston assemblies.
Be sure to replace piston assemblies without disassem-
bling new inner kit.
Pay attention to the orientation of piston cup, and insert
straight to prevent cup seal from being caught by cylin-
der inner wall.
BRA0031D
BRA0033D
SFIA2051E
Page 837 of 3502
BRAKE MASTER CYLINDER
BR-19
C
D
E
G
H
I
J
K
L
MA
B
BR
6. Remove snap ring while pressing in primary piston assembly
into prevent piston from popping out.
7. Hold primary piston rod, and then pull primary piston assembly,
plate, and guide assembly straight out.
8. Remove plate and guide assembly from primary piston assem-
bly.
CAUTION:
When removing plate from primary piston rod, make sure
inside of plate dose not damage rod.
9. Tap flange using a soft block, such as wood, and carefully pull
secondary piston assembly straight out to prevent a cylinder
body inner wall from being damaged.
Inspection After Disassembly
Cylinder body
Check a inner wall of cylinder for damage, abrasions, corrosion, and pinholes. Replace cylinder body if
detected.
Assembly
CAUTION:
Do not use mineral oils such as kerosene, gasoline during the cleaning and assembly process.
Make sure there is no foreign matter such as dirt or dust attached to inner cylinder wall, piston, or
piston cup seal, and use care to avoid damaging parts with assembly tools.
Do not drop parts. If a part is dropped, do not use it.
1. Apply brake fluid to cylinder inner wall, piston cup seal and con-
tact surfaces between piston assembly. Then insert secondary
piston assembly and primary piston assembly into cylinder body
in this order.
CAUTION:
Do not reuse primary and secondary piston assemblies.
Be sure to replace piston assemblies without disassem-
bling new inner kit.
Pay attention to the orientation of piston cup, and insert
straight to prevent piston cup seal from being caught by
cylinder inner wall.
2. Visually inspect secondary piston assembly slit through piston
stopper mounting hole and then install piston stopper while
pushing in primary piston assembly.
BRA0561D
BRA0033D
PFIA0263E
BRA0560D
Page 842 of 3502
BR-24
VACUUM LINES
VACUUM LINESPFP:41920
ComponentsBFS000BU
Removal and InstallationBFS000BV
CAUTION:
Because vacuum hose contains a check valve, it must be installed in the correct direction. Refer to
the stamp or label to confirm correct installation. Brake booster will not operate normally if hose is
installed in the wrong direction.
Insert vacuum hose at least 24 mm (0.94 in).
Do not use lubricating oil during assembly.
1. Clamp 2. Vacuum hose 3. Hose clamp
4. Vacuum tube 5. Vacuum hose (Build in check valve) 6. Engine side indicator stamp
A: To intake manifold
B: To brake booster
PFIA0823E
SBR225B
Page 847 of 3502
FRONT DISC BRAKE
BR-29
C
D
E
G
H
I
J
K
L
MA
B
BR
INSTALLATION
CAUTION:
Refill with new brake fluid “DOT 3 or DOT 4”.
Do not reuse drained brake fluid.
1. Install disc rotor.
CAUTION:
Align the matching marks of disc rotor and wheel hub,
which were marked at the time of removal when reusing
disc rotor.
2. Install brake caliper assembly to vehicle, and tighten torque
member mounting bolts to the specified torque. Refer to BR-26,
"Components" .
CAUTION:
Before installing torque member to vehicle, wipe oil and
grease on washer seats on steering knuckle and mounting
surface of torque member.
3. Install brake hose to brake caliper assembly, and tighten union bolts to the specified torque. Refer to BR-
26, "Components" .
CAUTION:
Do not reuse copper washers for union bolts.
Connect brake hose aligning with caliper assembly mounting protrusion.
4. Refill with new brake fluid and bleed air. Refer to BR-10, "
Bleeding Brake System" .
5. Check front disc brake for drag.
6. Install tyres to vehicle.
Disassembly and Assembly of Brake Caliper AssemblyBFS000C1
NOTE:
Do not remove torque member, pads, shims, inner shim cover, and pad retainers when disassembling and
assembling cylinder body.
DISASSEMBLY
1. Remove caliper assembly from Vehicle. Refer to BR-28, "Removal and Installation of Brake Caliper
Assembly" .
2. Remove sliding pin bolts, from cylinder body, and remove pads
shims shim cover and pad retainers from torque member.
CAUTION:
When removing pad retainers from torque member, lift
pad retainer in the direction by the arrow (shown in the
figure) so as not to damage it.
Do not drop pads, shims, inner shim cover and pad
retainers from torque member.
3. Remove sliding pins and sliding pin boots from torque member.
SDIA2608E
SBR556E
Page 848 of 3502
BR-30
FRONT DISC BRAKE
4. Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Do not get fingers caught in pistons.
5. Using a flat-bladed screwdriver, remove piston seal from cylin-
der body.
CAUTION:
Be careful not to damage a cylinder inner wall.
INSPECTION AFTER DISASSEMBLY
Cylinder Body
CAUTION:
Use new brake fluid to clean. Do not use mineral oils such as gasoline or kerosene.
Check inner wall of cylinder for corrosion, wear, and damage. If a malfunction is detected, replace cylinder
body.
Minor flaws caused by corrosion or a foreign material can be removed by polishing a surface of inner wall
with a fine sandpaper. Replace cylinder body, if necessary.
To r q u e M e m b e r
Check for wear, cracks, and damage. If a malfunction is detected, replace torque member.
Piston
CAUTION:
Piston sliding surface is plated. Do not polish with sandpaper.
Check piston surface for corrosion, wear, and damage. If a malfunction is detected, replace applicable part.
Sliding Pin, Sliding Pin Bolt, and Sliding Pin Boot
Check sliding pins and sliding pin boots for wear, damage, and cracks. If a malfunction is detected, replace
applicable part.
ASSEMBLY
1. Apply polyglycol ether based lubricant to piston seal, and install
them to cylinder body.
CAUTION:
Do not reuse piston seal.
MAA0272D
SFIA0999E
SFIA2278E