accelerator NISSAN TEANA 2003 User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: TEANA, Model: NISSAN TEANA 2003Pages: 3502, PDF Size: 74.56 MB
Page 55 of 3502
TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
5. Start engine and measure line pressure at idle and stall speed.
CAUTION:
Keep the brake pedal pressed all the way down during
measurement.
When measuring line pressure at stall speed, refer to AT-
43, "STALL TEST" .
Line Pressure
Judgement of Line Pressure Test
SAT493G
Engine speed rpmLine pressure kPa (bar, kg/cm2 , psi)
“D”, “3”, “2” and “1” positions “R” position
Idle 500 (5.00, 5.1, 73) 778 (7.78, 7.9, 113)
Stall 1,233 (12.33, 12.6, 179) 1,918 (19.18, 19.6, 278)
Judgement Suspected parts
At idleLine pressure is low in all positions.
Oil pump wear
Control piston damage
Pressure regulator valve or plug sticking
Spring for pressure regulator valve damaged
Fluid pressure leakage between oil strainer and pressure regulator valve
Clogged strainer
Line pressure is low in particular posi-
tion.
Fluid pressure leakage between manual valve and particular clutch
For example, line pressure is:
− Low in “R” and “1” positions, but
− Normal in “D”, “3” and “2” positions.
Therefore, fluid leakage exists at or around low and reverse brake circuit.
Refer to AT-18, "
CLUTCH AND BAND CHART" .
Line pressure is high.
Accelerator pedal position signal malfunction
A/T fluid temperature sensor damaged
Line pressure solenoid valve sticking
Short circuit of line pressure solenoid valve circuit
Pressure modifier valve sticking
Pressure regulator valve or plug sticking
Open in dropping resistor circuit
At stall
speedLine pressure is low.
Accelerator pedal position signal malfunction
Line pressure solenoid valve sticking
Short circuit of line pressure solenoid valve circuit
Pressure regulator valve or plug sticking
Pressure modifier valve sticking
Pilot valve sticking
Page 58 of 3502
AT-50
TROUBLE DIAGNOSIS
Cruise Test — Part 1BCS00106
1. CHECK STARTING GEAR (D1 ) POSITION
1. Drive vehicle for approximately 10 minutes to warm engine oil and ATF up to operating temperature.
2. Park vehicle on flat surface.
3. Move selector lever to “P” position.
4. Start engine.
5. Move selector lever to “D” position.
6. Accelerate vehicle by constantly depressing accelerator pedal half-way.
Read gear position. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does vehicle start from D
1 ?
YES >> GO TO 2.
NO >>
Mark the box AT- 1 8 2 , "Vehicle Cannot Be Started From D1" on the AT- 3 8 , "DIAGNOSTIC
WORKSHEET" .
Continue “Road Test”.
2. CHECK SHIFT-UP (D1 TO D2 )
Check shift-up (D
1 to D2 ).
Specified speed when shifting from D
1 to D2 (Throttle position: half throttle). Refer to AT- 5 4 , "Vehicle Speed
Which Gear Shifting Occurs" .
Read gear position, throttle opening and vehicle speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
1 to D2 at the specified speed?
YES >> GO TO 3.
NO >>
Mark the box AT- 1 8 4 , "A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2" on the
AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .
Continue “Road Test”.
3. CHECK SHIFT-UP (D2 TO D3 )
Check shift-up (D
2 to D3 ).
Specified speed when shifting from D
2 to D3 (Throttle position: half throttle). Refer to AT- 5 4 , "Vehicle Speed
Which Gear Shifting Occurs" .
Read gear position, throttle opening and vehicle speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
2 to D3 at the specified speed?
YES >> GO TO 4.
NO >>
Mark the box AT- 1 8 6 , "A/T Does Not Shift: D2 → D3" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .
Continue “Road Test”.
4. CHECK SHIFT-UP (D3 TO D4 )
Check shift-up (D
3 to D4 ).
Specified speed when shifting from D
3 to D4 (Throttle position: half throttle). Refer to AT- 5 4 , "Vehicle Speed
Which Gear Shifting Occurs" .
Read gear position, throttle opening and vehicle speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
3 to D4 at the specified speed?
YES >> GO TO 5.
NO >>
Mark the box AT- 1 8 8 , "A/T Does Not Shift: D3 → D4" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .
Continue “Road Test”. ATF operating temperature: 50 - 80°C (122 - 176°F)
Page 59 of 3502
TROUBLE DIAGNOSIS
AT-51
D
E
F
G
H
I
J
K
L
MA
B
AT
5. CHECK LOCK-UP (D4 TO D4 L/U)
Check lock-up (D
4 to D4 L/U).
Specified speed when lock-up occurs (Throttle position: half throttle). Refer to AT- 5 4 , "
Vehicle Speed at When
Lock-up Occurs/Releases" .
Read vehicle speed, throttle opening when lock-up duty becomes 94%. Refer to AT- 7 0 , "
DATA
MONITOR MODE" .
Does A/T perform lock-up at specified speed?
YES >> GO TO 6.
NO >>
Mark the box AT- 1 9 1 , "A/T Does Not Perform Lock-up" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .
Continue “Road Test”.
6. CHECK LOCK-UP HOLD
Check lock-up hold.
When lock-up duty becomes 94%. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T hold lock-up condition for more than 30 seconds?
YES >> GO TO 7.
NO >>
Mark the box AT- 1 9 3 , "A/T Does Not Hold Lock-up Condition" on the AT- 3 8 , "DIAGNOSTIC
WORKSHEET" .
Continue “Road Test”.
7. CHECK SHIFT-DOWN (D4 L/U TO D4 )
Release accelerator pedal.
When lock-up duty becomes 4%. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Is lock-up released when accelerator pedal is released?
YES >> GO TO 8.
NO >>
Mark the box AT- 1 9 5 , "Lock-up Is Not Released" on the AT- 3 8 , "DIAGNOSTIC WORKSHEET"
.
Continue “Road Test”.
8. CHECK SHIFT-DOWN (D4 TO D3 )
Decelerate vehicle by applying foot brake lightly.
Read gear position and engine speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does engine speed return to idle smoothly when A/T is shifted from D
4 to D3 ?
YES >> 1. Stop vehicle.
2. Go to AT- 5 1 , "
Cruise Test — Part 2" .
NO >>
Mark the box AT- 1 9 5 , "Engine Speed Does Not Return To Idle (Light Braking D4 → D3 )" on the
AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .
Continue “Road Test”.
Cruise Test — Part 2BCS00107
1. CHECK STARTING GEAR (D1 ) POSITION
1. Move selector lever to “D” position.
2. Accelerate vehicle by half throttle again.
Read gear position. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does vehicle start from D
1 ?
YES >> GO TO 2.
NO >>
Mark the box AT- 1 8 2 , "Vehicle Cannot Be Started From D1" on the AT- 3 8 , "DIAGNOSTIC
WORKSHEET" .
Continue “Road Test”.
Page 60 of 3502
AT-52
TROUBLE DIAGNOSIS
2. CHECK SHIFT-UP AND SHIFT-DOWN (D3 TO D4 TO D2 )
1. Accelerate vehicle to 80 km/h (50 MPH).
2. Release accelerator pedal and then quickly depress it fully.
Read gear position and throttle opening. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
4 to D2 as soon as accelerator pedal is depressed fully?
YES >> GO TO 3.
NO >>
Mark the box AT- 1 8 4 , "A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2" on the
AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .
Continue “Road Test”.
3. CHECK SHIFT-UP (D2 TO D3 )
Check shift-up (D
2 to D3 )
Specified speed when shifting from D
2 to D3 (Throttle position: full throttle). Refer to AT- 5 4 , "Vehicle Speed
Which Gear Shifting Occurs" .
Read gear position, throttle opening and vehicle speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
2 to D3 at the specified speed?
YES >> GO TO 4.
NO >>
Mark the box AT- 1 8 6 , "A/T Does Not Shift: D2 → D3" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .
Continue “Road Test”.
4. CHECK SHIFT-UP (D3 TO D4 ) AND ENGINE BRAKE
Release accelerator pedal after shifting from D
2 to D3 .
Read gear position, throttle opening and vehicle speed. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
3 to D4 and does vehicle decelerate by engine brake?
YES >> 1. Stop vehicle.
2. Go to AT- 5 2 , "
Cruise Test — Part 3" .
NO >>
Mark the box AT- 1 8 8 , "A/T Does Not Shift: D3 → D4" on the AT- 3 8 , "DIAGNOSTIC WORK-
SHEET" .
Continue “Road Test”.
Cruise Test — Part 3BCS00108
1. CHECK SHIFT-DOWN (D4 TO 33 )
1. More selector lever to “D” position.
2. Accelerate vehicle using half-throttle to D
4 .
3. Release accelerator pedal.
4. Move gear selector lever from “D” position to “3” position while driving in D
4 .
Read gear position. Refer to AT- 7 0 , "
DATA MONITOR MODE" .
Does A/T shift from D
4 to 33 ?
YES >> GO TO 2.
NO >>
Mark the box AT- 1 9 7 , "A/T Does Not Shift: D4 → 33 , When A/T Selector Lever “D” → “3”" on
the AT- 3 8 , "
DIAGNOSTIC WORKSHEET" .
Continue “Road Test”.
Page 62 of 3502
AT-54
TROUBLE DIAGNOSIS
Vehicle Speed Which Gear Shifting OccursBCS00109
FOR QR20DE ENGINE MODELS
At half throttle, the accelerator opening is 4/8 of the full opening.
FOR VQ23DE ENGINE MODELS
At half throttle, the accelerator opening is 4/8 of the full opening.
Vehicle Speed at When Lock-up Occurs/ReleasesBCS0010A
FOR QR20DE ENGINE MODELS
NOTE:
Perform lock-up inspection after warming up engine.
Lock-up vehicle speed may vary depending on the driving conditions and circumstances.
FOR VQ23DE ENGINE MODELS
NOTE:
Perform lock-up inspection after warming up engine.
Lock-up vehicle speed may vary depending on the driving conditions and circumstances. Throttle positionVehicle speed km/h (MPH)
D
1 → D2D2 → D3D3 → D4D4 → D3D3 → D2D2 → D1
Full throttle51 - 59
(32 - 37)96 - 104
(60 - 65)151 - 159
(94 - 99)147 - 155
(91 - 96)86 - 94
(53 - 58)40 - 48
(25 - 30)
Half throttle33 - 41
(21 - 25)62 - 70
(39 - 43)121 - 129
(75 - 80)77 - 85
(48 - 53)37 - 45
(23 - 28)5 - 13
(3 - 8)
Throttle positionVehicle speed km/h (MPH)
D1 → D2D2 → D3D3 → D4D4 → D3D3 → D2D2 → D1
Full throttle52 - 60
(32 - 37)97 - 105
(60 - 65)153 - 161
(95 - 100)149 - 157
(93 - 98)87 - 95
(54 - 59)41 - 49
(25 - 30)
Half throttle30 - 38
(19 - 24)58 - 66
(36 - 41)116 - 124
(72 - 77)69 - 77
(43 - 48)34 - 42
(21 - 26)5 - 13
(3 - 8)
Throttle position Selector lever positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
2.0/8 D position 86 - 94 (53 - 58) 61 - 69 (38 - 43)
3rd position 86 - 94 (53 - 58) 83 - 91 (52 - 57)
Throttle position Selector lever positionVehicle speed km/h (MPH)
Lock-up “ON” Lock-up “OFF”
2.0/8 D position 86 - 94 (53 - 58) 51 - 59 (32 - 37)
3rd position 86 - 94 (53 - 58) 83 - 91 (52 - 57)
Page 63 of 3502
TROUBLE DIAGNOSIS
AT-55
D
E
F
G
H
I
J
K
L
MA
B
AT
Symptom ChartBCS0010B
Numbers are arranged in order of inspection.
Perform inspections starting with number one and work up.
Items Symptom Condition Diagnostic item Reference page
No Lock-up
Engagement/
TCC InoperativeTorque converter
is not locked up.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. PNP switchAT- 1 6 1
4. Engine speed signalAT- 11 6
5. A/T fluid temperature sensorAT- 11 0
6. Line pressure testAT- 4 6
7. Torque converter clutch solenoid valveAT- 1 0 5
8. Control valve assemblyAT- 2 2 5
OFF vehicle 9. Torque converterAT- 2 5 5
Torque converter
clutch piston slip.ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. Torque converter clutch solenoid valveAT- 1 0 5
5. Line pressure solenoid valveAT- 1 2 6
6. Control valve assemblyAT- 2 2 5
OFF vehicle 7. Torque converterAT- 2 5 5
Lock-up point is
extremely high or
low.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Torque converter clutch solenoid valveAT- 1 0 5
4. Control valve assemblyAT- 2 2 5
Shift ShockSharp shock in
shifting from “N”
to “D” position.ON vehicle1. Engine idle speed
EC-45
*1, EC-387*2
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Line pressure testAT- 4 6
4. A/T fluid temperature sensorAT- 11 0
5. Engine speed signalAT- 11 6
6. Line pressure solenoid valveAT- 1 2 6
7. Control valve assemblyAT- 2 2 5
8. N-D accumulatorAT- 2 2 5
OFF vehicle 9. Forward clutchAT- 3 0 7
Too sharp a
shock in change
from D
1 to D2 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Accumulator servo releaseAT- 2 2 5
4. Control valve assemblyAT- 2 2 5
5. A/T fluid temperature sensorAT- 11 0
OFF vehicle 6. Brake bandAT- 3 2 9
Page 64 of 3502
AT-56
TROUBLE DIAGNOSIS
Shift ShockToo sharp a
shock in change
from D
2 to D3 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Control valve assemblyAT-225
OFF vehicle4. High clutchAT-3015. Brake bandAT-329
Too sharp a
shock in change
from D
3 to D4 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Line pressure testAT- 4 6
3. Control valve assemblyAT-225
OFF vehicle4. Brake bandAT-3295. Overrun clutchAT-307
6. Forward one-way clutchAT-319
Gear change
shock felt during
deceleration by
releasing acceler-
ator pedal.ON vehicle1. Accelerator pedal position sensor
EC-272*1, EC-652*2
2. Line pressure testAT- 4 6
3. Overrun clutch solenoid valveAT-100
4. Control valve assemblyAT-225
Large shock
changing from 1
2
to 1
1 in “1” posi-
tion.ON vehicle 1. Control valve assemblyAT-225OFF vehicle 2. Low & reverse brakeAT-315
Improper Shift
TimingToo high a gear
change point from
D
1 to D2 , from
D
2 to D3 , from
D
3 to D4 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Gear change
directly from D
1
to D
3 occurs.ON vehicle1. A/T fluid levelAT- 1 4
2. Accumulator servo releaseAT-225
OFF vehicle 3. Brake bandAT-329
Too high a
change point from
D
4 to D3 , from
D
3 to D 2 , from
D
2 to D1 .ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
Kickdown does
not operate when
depressing pedal
in D
4 within kick-
down vehicle
speed.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Kickdown oper-
ates or engine
overruns when
depressing pedal
in D
4 beyond
kickdown vehicle
speed limit.ON vehicle1. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0
, AT- 8 6
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
Gear change
from 2
2 to 23 in
“2” position.ON vehicle1. PNP switchAT-161
2. A/T positionAT-215
Items Symptom Condition Diagnostic item Reference page
Page 65 of 3502
TROUBLE DIAGNOSIS
AT-57
D
E
F
G
H
I
J
K
L
MA
B
AT
Improper Shift
TimingGear change
from 11 to 12 in
“1” position.ON vehicle1. PNP switchAT- 1 6 12. A/T positionAT- 2 1 5
No Down ShiftFailure to change
gear from D
4 to
D
3 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Overrun clutch solenoid valveAT- 1 0 0
4. Shift solenoid valve A AT- 9 0
5. Line pressure solenoid valveAT- 1 2 6
6. Control valve assemblyAT- 2 2 5
OFF vehicle7. Brake bandAT- 3 2 98. Overrun clutchAT- 3 0 7
Failure to change
gear from D
3 to
D
2 or from D4 to
D
2 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
5. Control valve assemblyAT- 2 2 5
OFF vehicle6. High clutchAT- 3 0 17. Brake bandAT- 3 2 9
Failure to change
gear from D
2 to
D
1 or from D3 to
D
1 .ON vehicle1. A/T fluid levelAT- 1 4
2. Accelerator pedal position sensor
EC-272*1, EC-652*2
3. Shift solenoid valve AAT- 9 0
4. Shift solenoid valve BAT- 9 5
5. Control valve assemblyAT- 2 2 5
OFF vehicle6. Low one-way clutchAT- 2 5 57. High clutchAT- 3 0 1
8. Brake bandAT- 3 2 9
Failure to change
from 3
3 to 22
when changing
lever into “2” posi-
tion.
AT-198ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. Shift solenoid valve BAT- 9 5
3. Control valve assembly AT- 2 2 5
4. A/T positionAT- 2 1 5
OFF vehicle 5. Brake bandAT- 3 2 9
Does not change
from 1
2 to 11 in
“1” position.ON vehicle1. PNP switchAT- 1 6 1
2. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
3. Shift solenoid valve AAT- 9 0
4. Control valve assemblyAT- 2 2 5
5. Overrun clutch solenoid valveAT- 1 0 0
OFF vehicle6. Overrun clutchAT- 3 0 77. Low & reverse brakeAT- 3 1 5
Items Symptom Condition Diagnostic item Reference page
Page 66 of 3502
AT-58
TROUBLE DIAGNOSIS
No Up ShiftFailure to change
gear from D
1 to
D
2 .ON vehicle1. A/T positionAT-215
2. Shift solenoid valve AAT- 9 0
3. Control valve assemblyAT-225
4. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
5. Accelerator pedal position sensor
EC-272*1, EC-652*2
OFF vehicle 6. Brake bandAT-329
Failure to change
gear from D
2 to
D
3 .ON vehicle1. A/T positionAT-215
2. Shift solenoid valve BAT- 9 5
3. Control valve assemblyAT-225
4. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
5. Accelerator pedal position sensor
EC-272*1, EC-652*2
OFF vehicle6. High clutchAT-3017. Brake bandAT-329
Failure to change
gear from D
3 to
D
4 .ON vehicle 1. PNP switchAT-161
2. 3rd position switchAT-161
3. A/T positionAT-215
4. Shift solenoid valve AAT- 9 0
5. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
6. A/T fluid temperature sensorAT- 11 0
OFF vehicle 7. Brake band AT-329
A/T does not shift
to D
4 when driv-
ing with changing
lever into “D”
position.ON vehicle1. Accelerator pedal position sensor
EC-272
*1, EC-652*2
2. PNP switchAT-161
3. 3rd position switchAT-161
4. Vehicle speed sensor·A/T (Revolution
sensor) and vehicle speed sensor·MTRAT- 8 0, AT- 8 6
5. Shift solenoid valve AAT- 9 0
6. Overrun clutch solenoid valveAT-100
7. Control valve assemblyAT-225
8. A/T fluid temperature sensorAT- 11 0
9. Line pressure solenoid valveAT-126
OFF vehicle10. Brake bandAT-32911. Overrun clutchAT-307
Items Symptom Condition Diagnostic item Reference page
Page 67 of 3502
TROUBLE DIAGNOSIS
AT-59
D
E
F
G
H
I
J
K
L
MA
B
AT
Slips/Will Not
EngageVehicle will not
run in “R” position
(but runs in “D”,
“3”, “2” and “1”
positions). Clutch
slips.
Very poor accel-
eration.ON vehicle1. A/T positionAT- 2 1 5
2. Stall testAT- 4 3
3. Line pressure testAT- 4 6
4. Line pressure solenoid valveAT- 1 2 6
5. Control valve assemblyAT- 2 2 5
OFF vehicle6. Reverse clutchAT- 2 9 6
7. High clutchAT- 3 0 1
8. Forward clutchAT- 3 0 7
9. Overrun clutchAT- 3 0 7
10. Low & reverse brakeAT- 3 1 5
Vehicle will not
run in “D”, “3” and
“2” positions (but
runs in “1” and
“R” positions).ON vehicle 1. A/T positionAT- 2 1 5
OFF vehicle 2. Low one-way clutchAT- 2 5 5
Vehicle will not
run in “D”, “3”, “2”
and “1” positions
(but runs in “R”
position). Clutch
slips.
Very poor accel-
eration.ON vehicle1. A/T fluid levelAT- 1 4
2. Stall testAT- 4 3
3. Line pressure testAT- 4 6
4. Line pressure solenoid valveAT- 1 2 6
5. Control valve assemblyAT- 2 2 5
6. N-D accumulatorAT- 2 2 5
OFF vehicle7. Reverse clutchAT- 2 9 6
8. High clutchAT- 3 0 1
9. Forward clutchAT- 3 0 7
10. Forward one-way clutchAT- 3 1 9
11. Low one-way clutchAT- 2 5 5
Clutches or
brakes slip some-
what in starting.ON vehicle1. A/T fluid levelAT- 1 4
2. A/T positionAT- 2 1 5
3. Accelerator pedal position sensor
EC-272*1, EC-652*2
4. Line pressure testAT- 4 6
5. Line pressure solenoid valveAT- 1 2 6
6. Control valve assemblyAT- 2 2 5
7. N-D accumulatorAT- 2 2 5
OFF vehicle8. Forward clutchAT- 3 0 7
9. Reverse clutchAT- 2 9 6
10. Low & reverse brakeAT- 3 1 5
11. Oil pumpAT- 2 7 5
12. Torque converterAT- 2 5 5
Items Symptom Condition Diagnostic item Reference page