Reverse NISSAN TEANA 2003 Service Manual

FRONT SUSPENSION MEMBER
FSU-17
C
D
F
G
H
I
J
K
L
MA
B
FSU

FRONT SUSPENSION MEMBERPFP:54401
Removal and InstallationBES0003S
REMOVAL
1. Remove cowl top panel and hood. Install engine slinger, and then hoist engine. (Models with VQ35DE)
Refer to EI-21, "
COWL TOP" , BL-13, "HOOD" .
2. Remove tires from the vehicle.
3. Remove undercover and splash guard.
4. Remove mounting nut on the lower side of stabilizer connecting
rod. Remove stabilizer connecting rod from stabilizer bar. Refer
to FSU-16, "
STABILIZER BAR" .
5. Remove fixing nut and bolt of transverse link ball joint, and then
remove transverse link from steering knuckle. Refer to FSU-14,
"TRANSVERSE LINK" .
6. Remove front exhaust tube. Refer to EX-2, "
EXHAUST SYS-
TEM" .
7. Remove heat insulator. (Except for QR20DE models)
8. Remove steering hydraulic piping bracket from front suspension
member and rear engine mounting insulator. Refer to PS-39,
"HYDRAULIC LINE" .
9. Set a jack under transaxle assembly.
10. Remove mounting bolts of front engine mounting bracket and front engine mounting insulator. Refer to
EM-223, "
ENGINE ASSEMBLY" .
11. Remove mounting bolts of rear engine mounting bracket and rear engine mounting insulator. Refer to EM-
223, "ENGINE ASSEMBLY" .
12. Remove steering gear mounting bolts, and then hang steering gear on vehicle. Refer to PS-17, "
POWER
STEERING GEAR AND LINKAGE" .
13. Set a jack under front suspension member.
14. Remove mounting nuts on the front side and rebound stopper of front suspension member.
15. Remove mounting nut and bolts of member stay, and then remove member stay. Refer to FSU-7, "
Com-
ponents" .
16. Gradually lower a jack to remove front suspension member, stabilizer bar and transverse link from vehicle
as a unit.
17. Remove front and rear engine mounting insulators from front suspension member. Refer to EM-223,
"ENGINE ASSEMBLY" .
18. Remove transverse link from front suspension member. Refer to FSU-14, "
TRANSVERSE LINK" .
19. Remove stabilizer bar from front suspension member.
INSPECTION AFTER REMOVAL
Check front suspension member for deformation, cracks, or other damage. Replace if there are.
INSTALLATION

Installation is the reverse order of the removal. For tightening torque, refer to FSU-7, "Components" .
NOTE:
Do not reuse non-reusable parts.

Perform final tightening of each of parts, under unladen conditions, which were removed when removing
front suspension member and transverse link. Check the wheel alignment. Refer to FSU-5, "
Wheel Align-
ment Inspection" .

Adjust neutral position of steering angle sensor after checking the wheel alignment for models with VDC.
Refer to BRC-40, "
Adjustment of Steering Angle Sensor Neutral Position" .
SEIA0375E

SERVICE INFORMATION FOR ELECTRICAL INCIDENT
GI-31
C
D
E
F
G
H
I
J
K
L
MB
GI

Control Unit Circuit Test
System Description:When the switch is ON, the control unit lights up the lamp.
INPUT-OUTPUT VOLTAGE CHART
The voltage value is based on the body ground.
*:If high resistance exists in the switch side circuit (caused by a single strand), terminal 1 does not detect battery voltage. Control unit
does not detect the switch is ON even if the switch does not turn ON. Therefore, the control unit does not supply power to light up the
lamp.
INPUT-OUTPUT VOLTAGE CHART
The voltage value is based on the body ground.
*:If high resistance exists in the switch side circuit (caused by a single strand), terminal 2 does not detect approx. 0V. Control unit does
not detect the switch is ON even if the switch does not turn ON. Therefore, the control unit does not control ground to light up the lamp.
Control Units and Electrical PartsBAS0007J
PRECAUTIONS

Never reverse polarity of battery terminals.

Install only parts specified for a vehicle.

Before replacing the control unit, check the input and output and functions of the component parts.

Do not apply excessive force when disconnecting a connector.
MGI034A
Pin
No.Item ConditionVoltage
value [V]In case of high resistance such as single strand [V] *
1 SwitchSwitch ON Battery voltage Lower than battery voltage Approx. 8 (Example)
Switch OFF Approx. 0 Approx. 0
2LampSwitch ON Battery voltage Approx. 0 (Inoperative lamp)
Switch OFF Approx. 0 Approx. 0
MGI035A
Pin
No.Item ConditionVoltage
value [V]In case of high resistance such as single strand [V] *
1 LampSwitch ON Approx. 0 Battery voltage (Inoperative lamp)
Switch OFF Battery voltage Battery voltage
2SwitchSwitch ON Approx. 0 Higher than 0 Approx. 4 (Example)
Switch OFF Approx. 5 Approx. 5

FRONT DOOR GLASS AND REGULATOR
GW-47
C
D
E
F
G
H
J
K
L
MA
B
GW

4. While holding the door window, raise it at the rear end to pull the
glass out of the sash toward the outside of the door.
Installation
Install in the reverse order of removal.
REGULATOR ASSEMBLY
Removal
1. Remove the front door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Operate the power window main switch to raise/lower the door
window until the glass mounting bolts can be seen.
3. Remove the glass mounting bolts.
4. Raise up the door glass and hold with a suction lifter.
5. Disconnect the harness connector for the module assembly.
6. Remove the module assembly mounting bolts.
7. Remove the locating pin on the right/left of the module assembly
from the door panel.
SIIA0286J
PIIA6316E
PIIB1811E
PIIA6317E

GW-48
FRONT DOOR GLASS AND REGULATOR

8. While lifting the module assembly, pull forward the lower of the
module assembly to remove.
9. Unclip the harness from the back of module assembly.
Installation
Install in the reverse order of removal.
Inspection after Removal
Check the regulator assembly for the following. If a malfunction is
detected, replace or grease it.

Wire wear

Regulator deformation

Grease condition for each sliding part
The arrows in the figure show the application points of the grease
“Multemp HL-D” or equivalent.
Disassembly and AssemblyBIS000ZQ
REGULATOR ASSEMBLY
Disassembly
Remove the power window motor and guide rail from the module
assembly.
Assembly
Assemble in the reverse order of disassembly.
PIIA6318E
PIIA6319E
PIIA6321J
PIIA6320E

GW-52
REAR DOOR GLASS AND REGULATOR

9. Unclip the harness at the lower of the door sash.
10. Pull out the rear door glass toward the outside of the door to remove.
11. Remove the door glass run from the door panel.
Installation
Install in the reverse order of removal.
REGULATOR ASSEMBLY
Removal
1. Remove the rear door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Remove the rear door speaker harness connector.
3. Remove the sealing screen.
NOTE:
If the sealing screen is reused, cut the butyl-tape so that a part of butyl-tape remains on the sealing screen.
4. Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
5. Remove the glass mounting bolts.
6. Raise up the door glass and hold with a suction lifter.
PIIA6325E
PIIA6322E
PIIB1817E

REAR DOOR GLASS AND REGULATOR
GW-53
C
D
E
F
G
H
J
K
L
MA
B
GW

7. Remove the power window motor harness connector and
mounting bolts, and remove the regulator assembly from the
panel.
Installation
Install in the reverse order of removal.
Inspection after Removal
Check the regulator assembly for the following. If a malfunction is
detected, replace or grease it.

Gear wear

Regulator deformation

Grease condition for each sliding part
The arrows in the figure show the application points of the grease
“Dow Corning Moly Coat SK623” or equivalent.
Inspection after InstallationBIS000ZT
FITTING INSPECTION

Make sure the glass is securely fit into the glass run groove.

Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)], and make sure the clearance to the sash
is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass and carrier plate mounting bolts to correct the glass position.
PIIA6326E
PIIA6327J

DOOR MIRROR
GW-77
C
D
E
F
G
H
J
K
L
MA
B
GW

Removal and InstallationBIS0010I
CAUTION:
Be careful not to damage the mirror body.
REMOVAL
1. Remove the front door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Remove the tweeter harness connector from the corner cover (tweeter equipped model).
3. Remove the door mirror harness connector.
4. Remove the corner cover.
5. Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA6330E
1. Door mirror assembly 2. Nut 3. Corner cover

GW-80
INSIDE MIRROR

INSIDE MIRRORPFP:96321
Removal and InstallationBIS0010K
REMOVAL
Slide the mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
1. Inside mirror
PIIA6795E

IP-18
INSTRUMENT PANEL ASSEMBLY

6. Disconnect sunload sensor, auto light sensor, and security indicator harness connectors. Refer to AT C -
111 , "SUNLOAD SENSOR" and LT- 7 4 , "Removal and Installation for Optical Sensor" .
7. Remove instrument panel & pad from passenger side door opening.
8. Remove screws, and then remove instrument panel pad from instrument panel.
(Z) Instrument Center Lower Panel
1. Remove screws from back of instrument panel & pad.
2. Remove instrument center lower panel forward from front side.
INSTALLATION
Install in the reverse order of removal.

IP-20
INSTRUMENT PANEL ASSEMBLY

8. Remove screws, and then remove console box.
9. Remove screws from both sides of bottom of rear end, and then remove console bracket.
Assembly
Assemble in the reverse order of disassembly.
INSTRUMENT PASSENGER LOWER PANEL
Disassembly
1. Remove caught point of tip of damper from back of glove box lid
side using a screwdriver wrapped with tape.
2. Remove screws from center of back surface, and then remove damper body.
3. Remove glove box pin from center of back surface using a
screwdriver wrapped with tape, and then remove glove box from
instrument passenger lower panel.
4. Remove illumination from back surface upper using a screwdriver wrapped with tape.
1. Pocket 2. Instrument passenger lower panel 3. Glove box pin
4. Glove box 5. Damper 6. Screw
7. Glove box illumination
PIIB1793E
PIIB1794E
PIIA6352E