Reverse NISSAN TEANA 2003 Service Manual

DIAGNOSIS SENSOR UNIT
SRS-47
C
D
E
F
G
I
J
K
L
MA
B
SRS

DIAGNOSIS SENSOR UNITPFP:28556
Removal and InstallationBHS0004M
REMOVAL
CAUTION:
Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
1. Disconnect each harness connector for the air bag module and seat belt pre-tensioner.
2. Remove A/T selector lever knob. Refer to IP-12, "
(C) A/T Selector Lever Knob" .
3. Remove A/T console finisher. Refer to IP-12, "
(D) A/T Console Finisher" .
4. Remove ashtray. Refer to IP-12, "
(F) Front Ashtray" .
5. Remove instrument panel lower cover (LH/RH). Refer to IP-13, "
(G) Instrument Panel Lower Cover (LH/
RH)" .
6. Remove instrument panel stay cover. Refer to IP-13, "
(H) Instrument Panel Stay Cover" .
7. Remove console rear cover. Refer to IP-13, "
(I) Console Rear Cover" .
8. Remove center console. Refer to IP-14, "
(J) Center Console" .
9. Disconnect diagnosis sensor unit connector.
10. Remove fixing bolts and ground bolt from the diagnosis sensor
unit.
CAUTION:

Do not use old bolts. Replace with new ones.

Check diagnosis sensor unit bracket to ensure that it is free
of deformation, dents, cracks or rust. If it shows any visible
things of damage, replace with new one.

Replace diagnosis sensor unit if it has been dropped or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Check the diagnosis sensor unit for proper installation.

After replacement of diagnosis sensor unit, perform self-diagnosis to make sure that no malfunc-
tion is detected. Refer to SRS-16, "
SRS Operation Check" .
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the
vehicle as equipped.Ground bolt : 6.9 N·m (0.70 kg-m, 61 in-lb)
Fixing bolt : 24.5 N·m (2.5 kg-m, 18 ft-lb)
PHIA1342E
Specification ECU DISCRIMINATED No.
Models with driver and passenger air bags, seat belt pre-tensioner AA90
Models with driver and passenger air bags, seat belt pre-tensioner, side air bags and curtain air bags AA8C

SRS-48
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONERPFP:00014
Caution for Air Bag Module and Seat Belt Pre-TensionerBHS0004N

Before disposing of air bag module and seat belt pre-tensioner, or vehicles equipped with such systems,
deploy the systems. If such systems have already been deployed due to an accident, dispose of them as
indicated in SRS-48, "
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER" .

When deploying the air bag module and seat belt pre-tensioner, always use the Special Service Tool;
Deployment tool (KV99106400).

When deploying the air bag module and seat belt pre-tensioner, stand at least 5 m (16 ft) away from the
deployment component.

When deploying air bag module and seat belt pre-tensioner, a fairly loud noise is made, followed by
smoke being released. The smoke is not poisonous, however, be careful not to inhale smoke since it irri-
tates the throat and can cause choking.

Always activate one air bag module at a time.

Due to heat, leave air bag module unattended for more than 30 minutes after deployment. Also leave seat
belt pre-tensioner unattended for more than 10 minutes after deployment.

Be sure to wear gloves when handling a deployed air bag module and seat belt pre-tensioner.

Never apply water to the deployed air bag module and seat belt pre-tensioner.

Wash your hands clean after finishing work.

Place the vehicle outdoors with an open space of at least 6 m (20 ft) on all sides when deploying air bag
module and seat belt pre-tensioner while mounted in vehicle.

Use a voltmeter to make sure the vehicle battery is fully charged.

Do not dispose the air bag module and seat belt pre-tensioner undeployed.
CHECKING DEPLOYMENT TOOL
Connecting to Battery
CAUTION:
The battery must show voltage of 9.6V or more.
Remove the battery from the vehicle and place it on dry wood blocks
approximately 5 m (16 ft) away from the vehicle.

Wait 3 minutes after the vehicle battery is disconnected before
proceeding.

Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal.
Make sure the polarity is correct. The right side lamp in the tool,
marked “deployment tool power”, should glow with a green
light. If the right side lamp glows red, reverse the connections
to the battery.
Deployment Tool Check
Press the deployment tool switch to the ON position. The left side
lamp in the tool, marked “air bag connector voltage” should illumi-
nate. If it does not illuminate, replace the tool.
PHIA0003E
SBF266H

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
SRS-49
C
D
E
F
G
I
J
K
L
MA
B
SRS

Air Bag Deployment Tool Lamp Illumination Chart (Battery Connected)
*: If this lamp glows red, the tool is connected to the battery incorrectly. Reverse the connections and make sure the lamp glows green.
DEPLOYMENT PROCEDURES FOR AIR BAG MODULE (OUTSIDE OF VEHICLE)
Unless the vehicle is being scrapped, deploying the air bag in the
vehicle is not recommended. This may cause damage to the vehicle
interior.
Anchor air bag module bracket (SST: KV99105300) in a vise
secured to a firm foundation during deployment.
Deployment of Driver Air Bag Module (Outside of Vehicle)
1. Using wire, secure air bag module to air bag module bracket
(SST: KV99105300) at two places.
CAUTION:
Use wire of at least 1 mm (0.04 in) diameter.
2. Firmly secure air bag module bracket (SST: KV99105300) with
air bag module attached, in a vise.
3. Connect deployment tool adapter (SST: KV99109700) to air bag
module connector and deployment tool connector (SST:
KV99106400).
4. Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal.
5. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
6. Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, will illuminate and
the air bag module will deploy.
CAUTION:
When deploying the driver air bag module, stand at least 5 m
(16 ft) away from the air bag module.
Switch operationLeft side lamp, green*
“AIR BAG CONNECTOR
VOLTAGE”Right side lamp, green*
“DEPLOYMENT TOOL
POWER”
OFF OFF ON
ON ON ON
SRS232-E
PHIA0608E
SRS020-A

FRONT WIPER AND WASHER SYSTEM
WW-37
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Front Washer NozzleBKS003WB
REMOVAL
1. Open hood.
2. While pushing nozzle spray point side along body, use the noz-
zle stop point as the support point and rotate nozzle to remove it
from body.
3. Remove washer tube.
INSTALLATION
1. Install washer tube in nozzle.
2. Install nozzle to the vehicle.
3. Adjust nozzle spray location. Refer to WW-36, "
Washer Nozzle Adjustment" .
CAUTION:
The spray points differ, so be sure to install left and right nozzles correctly.
Inspection for Washer NozzleBKS003WC
CHECK VALVE INSPECTION
Blow check valve. Confirm that the air ventilates. Also confirm that
inhalation is impossible.
Inspection of Front Wiper and Washer Switch CircuitBKS003WD
Refer to LT- 1 8 5 , "Combination Switch Inspection" .
Removal and Installation of Front Wiper and Washer SwitchBKS003WE
REMOVAL
1. Remove steering column cover. Refer to IP-11, "Removal and Installation" .
2. Disconnect the wiper and washer switch connector.
3. Pull wiper and washer switch toward the passenger door while
pressing pawls in direction shown by the arrow in the figure, and
remove it from the base.
INSTALLATION
Installation is the reverse order of removal.
SKIA0291J
PKIA1403E
SKIB0909E

WW-38
FRONT WIPER AND WASHER SYSTEM

Removal and Installation of Washer TankBKS003WF
REMOVAL
: Vehicle front
1. Pull washer tank inlet out of washer tank.
2. Remove washer tank mounting bolt (A).
3. Remove fender protector RH on front side. Refer to EI-23, "
FENDER PROTECTOR" .
4. Disconnect front washer pump connector (1).
5. Remove washer tank mounting bolts (A).
6. Remove washer tube (2), and remove washer tank (3) from
vehicle.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
After installation, and water up to the upper level of the washer tank inlet, and check for water leaks.
SKIA6395E
PKID0314E
PKID0315E
Washer tank mounting bolts : 4.5 N·m (0.46 kg-m, 40 in-lb)

FRONT WIPER AND WASHER SYSTEM
WW-39
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Front Washer PumpBKS003WG
REMOVAL
1. Remove fender protector RH on front side. Refer to EI-23,
"FENDER PROTECTOR" .
2. Disconnect front washer pump connector and remove washer
tube.
3. Pull out washer pump in direction shown by the arrow ( ) in the
figure. Remove front washer pump from washer tank.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
When installing front washer pump, there should be no packing twists, etc.
SKIB0910E

HEADLAMP WASHER
WW-57
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Headlamp Washer NozzleBKS002EX
REMOVAL
1. Pull out headlamp washer nozzle from a bumper, remove pawl
(A), and remove headlamp washer nozzle cover (1).
2. Remove undercover one.
3. Remove fender protector. Refer to EI-23, "
FENDER PROTEC-
TOR" .
4. Remove front bumper. Refer to EI-14, "
FRONT BUMPER" .
5. Remove headlamp washer tube (1). Refer to WW-58, "
Removal
and Installation of Headlamp Washer Tube Connector" .
6. Removal headlamp washer nozzle retainer (A).
7. Removal headlamp washer nozzle bracket (2).
8. Remove headlamp washer nozzle assembly (3).

The check valve is installed in headlamp washer nozzle
assembly.

The check valve prevents backflow of washer fluid.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
When installing nozzle, there should be no packing twist, etc.
AdjustmentBKS002EY
PKIC9877E
PKIC9878E
PKIC9879E
a: 45° ±3°
b: 46° ±3°
c: 14° ±3°
d: 11° ±3°

WW-58
HEADLAMP WASHER

Removal and Installation of Washer TankBKS002EZ
Refer to WW-38, "Removal and Installation of Washer Tank" .
Removal and Installation of Headlamp Washer Tube ConnectorBKS002F0
REMOVAL
Remove headlamp washer tube while pressing the area that has no
pawls (A) of headlamp washer tube connector (1), in direction shown
by the arrow ( ) in the figure.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Headlamp Washer PumpBKS002F1
REMOVAL
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER" .
2. Disconnect headlamp washer pump connector (1).
3. Remove headlamp washer tube (2). Refer to WW-58, "
Removal
and Installation of Headlamp Washer Tube Connector" .
4. Remove the headlamp washer pump mounting bolt (A).
5. Remove the headlamp washer pump (3) from washer tank.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
When installing headlamp washer pump, there should be no packing twist, etc.
Removal and Installation of Headlamp Washer SwitchBKS003XZ
1. Remove instrument driver lower panel. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Spread pawls (A) of instrument driver lower panel to remove
headlamp washer switch(1).
SKIB8842E
PKIC9880E
Headlamp washer pump
mounting bolt:4.5 N·m (0.46 kg-m, 40 in-lb)
PKID0329E

CIGARETTE LIGHTER
WW-61
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and InstallationBKS001UC
REMOVAL
1. Remove ashtray. Refer to IP-10, "INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws from rearward cigarette lighter socket.
3. Pull out cigarette lighter.
4. Insert a small screwdriver or similar tool between the cigarette
lighter socket and cigarette lighter ring. Pull out cigarette lighter
socket.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Align notches of cigarette lighter ring and cigarette lighter socket when installing.
SKIA6400E
SKIA6401E

HORN
WW-63
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and InstallationBKS001UE
REMOVAL
1. Disconnect all horn connectors.
2. Remove horn mounting bolt, and remove horn from vehicle.
INSTALLATION
Installation is the reverse order of removal.
SKIB0911E
Horn mounting bolt : 17.1 N·m (1.7 kg-m, 13ft-lb)