heater NISSAN TEANA 2003 Owner's Manual

CVT FLUID COOLER SYSTEM
CVT-189
D
E
F
G
H
I
J
K
L
MA
B
CVT

CVT FLUID COOLER SYSTEMPFP:21600
CVT Fluid Cooler Removal and InstallationBCS001MX
COMPONENTS
1. Harness bracket 2. CVT fluid cooler inlet tube assembly 3. Transaxle assembly
4. Hose clamp 5. Inlet water hose 6. Hose clamp
7. Outlet water hose 8. Heater hose 9. Hose clamp
10. CVT fluid cooler outlet tube assem-
bly11. CVT fluid cooler valve assembly
A. O-ring
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-10, "
Components" .
However, refer to the following symbols for others.
: Apply engine coolant or equivalent.
SCIA7740E

CVT FLUID COOLER SYSTEM
CVT-191
D
E
F
G
H
I
J
K
L
MA
B
CVT

9. Remove air cleaner bracket. Refer to EM-131, "Removal and
Installation" .
10. Remove control cable from transaxle assembly. Refer to CVT-
176, "Removal and Installation" .
11. Remove water bypass hose (1) from water bypass pipe (2).
Refer to CO-52, "
Removal and Installation" .
: Hose clamp
12. Remove harness bracket and control cable bracket from tran-
saxle assembly. Refer to CVT-176, "
Removal and Installation"
and CVT-177, "CONTROL CABLE COMPONENTS" .
13. Remove inlet water hose and outlet water hose. Refer to CVT-
189, "COMPONENTS" .
14. Remove heater hose from heater pipe. Refer to CO-52,
"Removal and Installation" .
15. Remove CVT fluid cooler valve assembly from transaxle assem-
bly. Refer to CVT-189, "
COMPONENTS" .
16. Remove heater hose from CVT fluid cooler valve assembly (1).
: Hose clamp
17. Remove CVT fluid cooler inlet tube assembly and CVT fluid
cooler outlet tube assembly from CVT fluid cooler valve assem-
bly (1).
: bolt (2)
SCIA2752E
SCIA7919E
SCIA2753E
SCIA7854E
SCIA7855E

TRANSAXLE ASSEMBLY
CVT-195
D
E
F
G
H
I
J
K
L
MA
B
CVT

14. Remove crankshaft position sensor (POS) (1) from engine
assembly. Refer to EM-145, "
Removal and Installation" .
CAUTION:

Do not subject it to impact by dropping or hitting it.

Do not disassemble.

Do not allow metal filings, etc., to get on the sensor's
front edge magnetic area.

Do not place in an area affected by magnetism.
15. Remove starter motor. Refer to SC-18, "
Removal and Installa-
tion" .
16. Remove CVT fluid cooler valve assembly (1). (With CVT fluid
cooler tube assembly and heater hose). Refer to CVT-189, "
CVT
Fluid Cooler Removal and Installation" .
(A): Bolt (4)
(B): Hose clamp (3)
17. Install slinger to transaxle assembly.
18. Remove LH engine mounting bracket and LH engine mounting
insulator.
19. Remove transaxle assembly fixing bolts with power tool.
20. Remove transaxle assembly from engine assembly with a hoist.
CAUTION:
Secure torque converter to prevent it from dropping.
21. Remove air breather hose. Refer to CVT-186, "
Removal and
Installation" .
22. Remove CVT fluid cooler hoses.
23. Remove fluid cooler tube.
SCIA6759E
SCIA6880E
SCIA4355E
SCIA1868E

EC-4 DTC P2138 APP SENSOR .....................................272
Component Description ........................................272
CONSULT-II Reference Value in Data Monitor Mode
.272
On Board Diagnosis Logic ....................................272
DTC Confirmation Procedure ...............................273
Wiring Diagram .....................................................274
Diagnostic Procedure ...........................................275
Component Inspection ..........................................279
Removal and Installation ......................................279
ELECTRICAL LOAD SIGNAL ................................280
Description ............................................................280
CONSULT-II Reference Value in Data Monitor Mode
.280
Diagnostic Procedure ...........................................280
EVAP CANISTER PURGE VOLUME CONTROL
SOLENOID VALVE .................................................282
Description ............................................................282
CONSULT-II Reference Value in Data Monitor Mode
.282
Wiring Diagram .....................................................283
Diagnostic Procedure ...........................................285
Component Inspection ..........................................288
Removal and Installation ......................................288
FUEL INJECTOR ....................................................289
Component Description ........................................289
CONSULT-II Reference Value in Data Monitor Mode
.289
Wiring Diagram .....................................................290
Diagnostic Procedure ...........................................291
Component Inspection ..........................................293
Removal and Installation ......................................294
FUEL PUMP ............................................................295
Description ............................................................295
CONSULT-II Reference Value in Data Monitor Mode
.295
Wiring Diagram .....................................................296
Diagnostic Procedure ...........................................297
Component Inspection ..........................................300
Removal and Installation ......................................300
HO2S1 .....................................................................301
Component Description ........................................301
CONSULT-II Reference Value in Data Monitor Mode
.301
Wiring Diagram .....................................................302
Diagnostic Procedure ...........................................304
Component Inspection ..........................................305
Removal and Installation ......................................307
HO2S1 HEATER .....................................................308
Description ............................................................308
CONSULT-II Reference Value in Data Monitor Mode
.308
Wiring Diagram .....................................................309
Diagnostic Procedure ...........................................310
Component Inspection ..........................................312
Removal and Installation ......................................312
HO2S2 .....................................................................313
Component Description ........................................313CONSULT-II Reference Value in Data Monitor Mode
.313
Wiring Diagram .....................................................314
Diagnostic Procedure ............................................315
Component Inspection ..........................................317
Removal and Installation .......................................318
HO2S2 HEATER ......................................................319
Description ............................................................319
CONSULT-II Reference Value in Data Monitor Mode
.319
Wiring Diagram .....................................................320
Diagnostic Procedure ............................................321
Component Inspection ..........................................323
Removal and Installation .......................................323
IAT SENSOR ...........................................................324
Component Description ........................................324
Wiring Diagram .....................................................325
Diagnostic Procedure ............................................326
Component Inspection ..........................................328
Removal and Installation .......................................328
IGNITION SIGNAL ..................................................329
Component Description ........................................329
Wiring Diagram .....................................................330
Diagnostic Procedure ............................................333
Component Inspection ..........................................337
Removal and Installation .......................................338
REFRIGERANT PRESSURE SENSOR ..................339
Component Description ........................................339
Wiring Diagram .....................................................340
Diagnostic Procedure ............................................341
Removal and Installation .......................................343
MI & DATA LINK CONNECTORS ...........................344
Wiring Diagram .....................................................344
SERVICE DATA AND SPECIFICATIONS (SDS) ....346
Fuel Pressure ........................................................346
Idle Speed and Ignition Timing ..............................346
Mass Air Flow Sensor ...........................................346
Intake Air Temperature Sensor .............................346
Engine Coolant Temperature Sensor ....................346
Crankshaft Position Sensor (POS) .......................346
Camshaft Position Sensor (PHASE) .....................346
Heated Oxygen Sensor 1 Heater ..........................346
Heated Oxygen sensor 2 Heater ..........................346
Throttle Control Motor ...........................................346
Fuel Injector ..........................................................346
Fuel Pump .............................................................346
VQ
INDEX FOR DTC .....................................................347
DTC No. Index ......................................................347
Alphabetical Index .................................................349
PRECAUTIONS .......................................................351
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................351
On Board Diagnostic (OBD) System of Engine ....351
Precaution .............................................................351

EC-8 Diagnostic Procedure ...........................................648
Component Inspection ..........................................651
Removal and Installation ......................................651
DTC P2138 APP SENSOR .....................................652
Component Description ........................................652
CONSULT-II Reference Value in Data Monitor Mode
.652
On Board Diagnosis Logic ....................................652
DTC Confirmation Procedure ...............................653
Wiring Diagram .....................................................654
Diagnostic Procedure ...........................................655
Component Inspection ..........................................659
Removal and Installation ......................................659
ASCD BRAKE SWITCH ..........................................660
Component Description ........................................660
CONSULT-II Reference Value in Data Monitor Mode
.660
Wiring Diagram .....................................................661
Diagnostic Procedure ...........................................662
Component Inspection ..........................................666
ASCD INDICATOR ..................................................667
Component Description ........................................667
CONSULT-II Reference Value in Data Monitor Mode
.667
Wiring Diagram .....................................................668
Diagnostic Procedure ...........................................669
ELECTRICAL LOAD SIGNAL ................................670
Description ............................................................670
CONSULT-II Reference Value in Data Monitor Mode
.670
Diagnostic Procedure ...........................................670
ELECTRONIC CONTROLLED ENGINE MOUNT ..672
System Description ...............................................672
CONSULT-II Reference Value in Data Monitor Mode
.672
Wiring Diagram .....................................................673
Diagnostic Procedure ...........................................674
EVAP CANISTER PURGE VOLUME CONTROL
SOLENOID VALVE .................................................677
Description ............................................................677
CONSULT-II Reference Value in Data Monitor Mode
.677
Wiring Diagram .....................................................678
Diagnostic Procedure ...........................................680
Component Inspection ..........................................683
Removal and Installation ......................................683
FUEL INJECTOR ....................................................684
Component Description ........................................684
CONSULT-II Reference Value in Data Monitor Mode
.684
Wiring Diagram .....................................................685
Diagnostic Procedure ...........................................686
Component Inspection ..........................................689
Removal and Installation ......................................689
FUEL PUMP ............................................................690
Description ............................................................690
CONSULT-II Reference Value in Data Monitor Mode
.690
Wiring Diagram .....................................................691Diagnostic Procedure ............................................692
Component Inspection ..........................................695
Removal and Installation .......................................695
HO2S1 .....................................................................696
Component Description ........................................696
CONSULT-II Reference Value in Data Monitor Mode
.696
Wiring Diagram .....................................................697
Diagnostic Procedure ............................................700
Component Inspection ..........................................704
Removal and Installation .......................................705
HO2S1 HEATER ......................................................706
Description ............................................................706
CONSULT-II Reference Value in Data Monitor Mode
.706
Wiring Diagram .....................................................707
Diagnostic Procedure ............................................711
Component Inspection ..........................................713
Removal and Installation .......................................713
HO2S2 .....................................................................714
Component Description ........................................714
CONSULT-II Reference Value in Data Monitor Mode
.714
Wiring Diagram .....................................................715
Diagnostic Procedure ............................................718
Component Inspection ..........................................720
Removal and Installation .......................................722
HO2S2 HEATER ......................................................723
Description ............................................................723
CONSULT-II Reference Value in Data Monitor Mode
.723
Wiring Diagram .....................................................724
Diagnostic Procedure ............................................727
Component Inspection ..........................................729
Removal and Installation .......................................729
IAT SENSOR ...........................................................730
Component Description ........................................730
Wiring Diagram .....................................................731
Diagnostic Procedure ............................................732
Component Inspection ..........................................734
Removal and Installation .......................................734
IGNITION SIGNAL ..................................................735
Component Description ........................................735
Wiring Diagram .....................................................736
Diagnostic Procedure ............................................741
Component Inspection ..........................................746
Removal and Installation .......................................747
REFRIGERANT PRESSURE SENSOR ..................748
Component Description ........................................748
Wiring Diagram .....................................................749
Diagnostic Procedure ............................................750
Removal and Installation .......................................752
VIAS .........................................................................753
Description ............................................................753
CONSULT-II Reference Value in Data Monitor Mode
.754
Wiring Diagram .....................................................755
Diagnostic Procedure ............................................757

EC-9
C
D
E
F
G
H
I
J
K
L
M
ECA
Component Inspection ......................................... 760
Removal and Installation ...................................... 761
VSS ......................................................................... 762
Description ........................................................... 762
Diagnostic Procedure ........................................... 762
MI & DATA LINK CONNECTORS .......................... 763
Wiring Diagram .................................................... 763
SERVICE DATA AND SPECIFICATIONS (SDS) .... 765
Fuel Pressure ....................................................... 765
Idle Speed and Ignition Timing ............................. 765Mass Air Flow Sensor ...........................................765
Intake Air Temperature Sensor .............................765
Engine Coolant Temperature Sensor ...................765
Heated Oxygen Sensor 1 Heater .........................765
Heated Oxygen sensor 2 Heater ..........................765
Crankshaft Position Sensor (POS) .......................765
Camshaft Position Sensor (PHASE) ....................765
Throttle Control Motor ...........................................765
Fuel Injector ..........................................................765
Fuel Pump ............................................................766

TROUBLE DIAGNOSIS
EC-73
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EC

2R/LHeated oxygen sensor 2
heater[Engine is running]

Engine speed: Below 3,800 rpm after the
following conditions are met
–Engine: After warming up
–Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for
1 minute under no load0 - 1.0V
[Ignition switch: ON]

Engine stopped
[Engine is running]

Engine speed: Above 3,800 rpmBATTERY VOLTAGE
(11 - 14V)
3 G/WThrottle control motor relay
power supply[Ignition switch: ON]BATTERY VOLTAGE
(11 - 14V)
4LThrottle control motor
(Close)[Ignition switch: ON]

Engine stopped

Shift lever: D

Accelerator pedal: Fully released0 - 14V
5YThrottle control motor
(Open)[Ignition switch: ON]

Engine stopped

Shift lever: D

Accelerator pedal: Fully depressed0 - 14V
12 WPower steering pressure
sensor[Engine is running]

Steering wheel: Being turned0.5 - 4.0V
[Engine is running]

Steering wheel: Not being turned0.4 - 0.8V
13 WCrankshaft position
sensor (POS)[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on
rpm at idleApproximately 3.0V
[Engine is running]

Engine speed: 2,000 rpmApproximately 3.0V TERMI-
NAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB1104E
PBIB1105E
PBIB0527E
PBIB0528E

TROUBLE DIAGNOSIS
EC-75
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EC

22
23
41
42R/Y
R/B
LG/R
R/WFuel injector No. 3
Fuel injector No. 1
Fuel injector No. 4
Fuel injector No. 2[Engine is running]

Warm-up condition

Idle speed
NOTE:
The pulse cycle changes depending on
rpm at idleBATTERY VOLTAGE
(11 - 14V)
[Engine is running]

Warm-up condition

Engine speed: 2,000 rpmBATTERY VOLTAGE
(11 - 14V)
24 O/BHeated oxygen sensor 1
heater[Engine is running]

Warm-up condition

Engine speed: Below 3,600 rpmApproximately 7.0V
[Engine is running]

Engine speed: Above 3,600 rpmBATTERY VOLTAGE
(11 - 14V)
29 BSensor ground
[Camshaft position sensor
(PHASE)][Engine is running]

Warm-up condition

Idle speedApproximately 0V
30 BSensor ground
[Crankshaft position sensor
(POS)][Engine is running]

Warm-up condition

Idle speedApproximately 0V
34 L/YIntake air temperature sen-
sor[Engine is running]Approximately 0 - 4.8V
Output voltage varies with intake
air temperature.
35 W/B Heated oxygen sensor 1[Engine is running]

Warm-up condition

Engine speed: 2,000 rpm0 - Approximately 1.0V
(Periodically change)
46 BR/WSensor power supply
(Refrigerant pressure sen-
sor)[Ignition switch: ON]Approximately 5V
47 GSensor power supply
(Throttle position sensor)[Ignition switch: ON]Approximately 5V TERMI-
NAL
NO.WIRE
COLORITEM CONDITION DATA (DC Voltage)
PBIB0529E
PBIB0530E
PBIB0519E

TROUBLE DIAGNOSIS
EC-81
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EC

ENGINE CONTROL COMPONENT PARTS/CONTROL SYSTEMS APPLICATION
X: Applicable
*1: This item includes 1st trip DTCs.
*2: This mode includes 1st trip freeze frame data or freeze frame data. The items appear on CONSULT-II screen in freeze frame data
mode only if a 1st trip DTC or DTC is detected. For details, refer to EC-35
. ItemDIAGNOSTIC TEST MODE
WORK
SUPPORTSELF-DIAGNOSTIC
RESULTS
DATA
MONI-
TORDATA
MONITOR
(SPEC)ACTIVE
TEST DTC*
1FREEZE
FRAME
DATA*
2
ENGINE CONTROL COMPONENT PARTS
INPUT
Crankshaft position sensor (POS)××××
Camshaft position sensor (PHASE)×××
Mass air flow sensor×××
Engine coolant temperature sensor×××××
Heated oxygen sensor 1×××
Heated oxygen sensor 2××
Vehicle speed signal××××
Accelerator pedal position sensor×××
Throttle position sensor×××
Intake air temperature sensor×× ×
Knock sensor×
Refrigerant pressure sensor××
Closed throttle position switch (accelerator
pedal position sensor signal)××
Air conditioner switch××
Park/neutral position (PNP) switch×××
Stop lamp switch×××
Power steering pressure sensor×××
Battery voltage××
Electrical load signal××
ENGINE CONTROL COMPONENT PARTS
OUTPUT
Fuel injector×××
Power transistor (Ignition timing)×××
Throttle control motor relay×××
Throttle control motor×
EVAP canister purge volume control sole-
noid valve×××
Air conditioner relay××
Fuel pump relay××××
Cooling fan relay××××
Heated oxygen sensor 1 heater××
Heated oxygen sensor 2 heater××
Intake valve timing control solenoid valve××××

EC-84
[QR]
TROUBLE DIAGNOSIS

INT/A TEMP SE
[°C] or [°F]××
The intake air temperature (determined by
the signal voltage of the intake air tempera-
ture sensor) is indicated.
START SIGNAL
[ON/OFF]××

Indicates start signal status [ON/OFF] com-
puted by the ECM according to the signals
of engine speed and battery voltage.
After starting the engine, [OFF] is dis-
played regardless of the starter sig-
nal.
CLSD THL POS
[ON/OFF]××

Indicates idle position [ON/OFF] computed
by ECM according to the accelerator pedal
position sensor signal.
AIR COND SIG
[ON/OFF]××

Indicates [ON/OFF] condition of the air con-
ditioner switch as determined by the air
conditioner signal.
P/N POSI SW
[ON/OFF]××

Indicates [ON/OFF] condition from the park/
neutral position (PNP) switch signal.
PW/ST SIGNAL
[ON/OFF]××

[ON/OFF] condition of the power steering
system (determined by the power steering
pressure sensor signal) is indicated.
LOAD SIGNAL
[ON/OFF]××

Indicates [ON/OFF] condition from the elec-
trical load signal.
ON: Rear window defogger switch is ON
and/or lighting switch is in 2nd position.
OFF: Both rear window defogger switch
and lighting switch are OFF.
IGNITION SW
[ON/OFF]×

Indicates [ON/OFF] condition from ignition
switch.
HEATER FAN SW
[ON/OFF]×

Indicates [ON/OFF] condition from the
heater fan switch signal.
BRAKE SW
[ON/OFF]×

Indicates [ON/OFF] condition from the stop
lamp switch signal.
INJ PULSE-B1
[msec]×

Indicates the actual fuel injection pulse
width compensated by ECM according to
the input signals.
When the engine is stopped, a cer-
tain computed value is indicated.
IGN TIMING [BTDC]×

Indicates the ignition timing computed by
ECM according to the input signals.
When the engine is stopped, a cer-
tain value is indicated.
PURG VOL C/V [%]

Indicates the EVAP canister purge volume
control solenoid valve control value com-
puted by the ECM according to the input
signals.

The opening becomes larger as the value
increases.
INT/V TIM (B1) [°CA]

Indicates [°CA] of intake camshaft
advanced angle.
INT/V SOL (B1) [%]

The control value of the intake valve timing
control solenoid valve (determined by ECM
according to the input signal) is indicated.

The advance angle becomes larger as the
value increases
AIR COND RLY
[ON/OFF]×

The air conditioner relay control condition
(determined by ECM according to the input
signals) is indicated. Monitored item [Unit]ECM
INPUT
SIG-
NALSMAIN
SIG-
NALSDescription Remarks